Advertisement
Quick Links
PEPSI
®
The information contained in this document is subject to change without notice.
SCHROEDER AMERICA MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. SCHROEDER AMERICA shall not be liable for errors contained herein or for incidental consequential
damages in connection with the finishings, performance, or use of this material.
This document contains proprietary information which is protected by copyright. All right reserved.
This manual must be read and understood before the installation and operation of this dispenser.
PATENT NUMBERS: PATENT PENDING US & FOREIGN
INSTALLATION INSTRUCTION, PARTS LIST
AND CONFIGURATION GUIDE
4 FLAVOR ELECTRIC DISPENSER
Dispenser Model No. 959
© Copyright 2015 by Schroeder America, all rights reserved.
THIS DOCUMENT CONTAINS IMPORTANT INFORMATION
5620 Business Park • San Antonio, TX 78218
210.662.8200 • Fax: 210.667.2600 • www.schroederamerica.com
Toll-Free 877.404.2488
Please refer to the Schroeder America website (www.schroederamerica.com)
for information relating to Schroeder America installation and Service
Manuals, Instruction Sheets, Technical Bulletins, Service Bulletins, etc.
FOR THE
GEN. II
NOTICE:
Schroeder America
Rev: 2/18
PN: 805-0035
Advertisement
Related Manuals for Schroeder America 959
Summary of Contents for Schroeder America 959
- Page 1 BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SCHROEDER AMERICA shall not be liable for errors contained herein or for incidental consequential damages in connection with the finishings, performance, or use of this material.
-
Page 2: Installation
1. DISPENSER DIMENSIONS AND WEIGHT A. Four Flavor Electric Dispenser weight is 23 lb. B. Four Flavor Electric Dispenser shipping weight is 26 lb. C. Four Flavor Electric Dispenser shipping dimensions 12.75” x 18” x 34” 14.539 28.071 4.193 14.000 9.726 9.000 .854... - Page 3 Fig. 3.1 (Bottom of unit) IMPORTANT THIS APPLIANCE IS NOT TO BE USED BY CHILDREN OR PERSONS WITH REDUCED PHYSICAL, SENSORY OR MENTAL PN 333-0006 CAPABILITIES, OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION. CHILDREN SHOULD BE SUPERVISED TO ENSURE THEY DO NOT PLAY WITH APPLIANCE.
- Page 4 C. CONNECTION TO ELECTRICAL POWER BACK OF UNIT WARNING VALVE AND LIGHT SWITCHES MUST BE IN THE OFF POSITION WHEN CONNECTING UNIT TO POWER SUPPLY POWER INLET TO POWER RECEPTACLE ON UNIT TO 115V/60HZ WALL RECEPTACLE NEMA 5-15 R/5-15P WARNING THIS UNIT MUST BE PROPERLY ELECTRICALLY GROUNDED TO AVOID POSSIBLE FATAL ELECTRICAL SHOCK OR SERIOUS INJURY TO THE OPERATOR.
- Page 5 IMPORTANT THIS EQUIPMENT TO BE INSTALLED WITH ADEQUATE BACKFLOW PROTECTION. RECOMMENDED PART …APOLLO MODEL NO. DUCLF4A NOTE: Water Regulation is highly recommended. Set water regulator to 65 PSIG. Water pipe connections and fixtures Fig. 3.2 directly connected to a potable water View from back of unit supply shall be sized, installed and with back panel removed...
- Page 6 DO NOT ADJUST WATER VALVE, ONLY ADJUST SYRUP VALVES. A. Remove nozzle by twisting clockwise and pull down. B. Install Schroeder America Syrup Separator (P.N.: 316-0004) in place of nozzle to set ratio. NOTE: Membrane Switch (Fig. 4.1) is used to actuate the syrup and water solenoid valves.
- Page 7 DRILL 6. CLEANING AND SANITIZING The Schroeder America Dispenser is shipped from the factory cleaned and sanitized in accordance with NSF guidelines. The dispenser must also be cleaned and sanitized after installation is complete. It is recommended that the operator provide continuous maintenance as required by the manual and/or state and local guidelines to ensure proper operation.
- Page 8 IMPORTANT ONLY USE INTERNAL CLEANING SOLUTIONS THAT ARE APPROVED FOR BEVERAGE DISPENSER APPLICATIONS, SUCH AS BevClean™. (NO CAUSTIC CHEMICALS SUCH AS INDUSTRIAL KITCHEN CLEANING CHEMICALS SHOULD EVER BE USED) C. External Cleaning: The stainless steel dispenser and merchandiser can be cleaned by wiping with a cloth soaked with warm cleansing detergent.
- Page 9 10. Remove nozzle from bath; air dry before re-installing onto diffuser. 11. Reinstall merchandiser. F. Sanitizing Water Circuits: Cleaning and Sanitizing are not required for potable water circuits. The potable water lines should remain connected during the cleaning procedures for the concentrate circuits to avoid contamination.
-
Page 10: Troubleshooting
7. TROUBLE SHOOTING A. No water dispensed • Check water supply • Check Shut-off block knob (is it open) • Check ratio/brix adjustment • Line plugged • Water regulator installed (65 PSI or less) B. No syrup dispensed • Check CO pressure (55 psig +/- 5 psig) •... - Page 11 8. TO REMOVE AND REPLACE THE PCB (PRINTED CIRCUIT BOARD) (P.N. 600-0013) WARNING DISCONNECT POWER FROM SUPPLY CIRCUIT BEFORE OPENING BACK PANEL. A. Remove the lid, back panel and merchandiser from unit. B. Disconnect the membrane switch and solenoid valves from the PCB. (Fig. 8.1 & 8.2) C.
-
Page 12: Included Accessories
INCLUDED ACCESSORIES CUP REST DRIP TRAY CUP REST DRIP TRAY P.N. 661-0019 P.N. 265-0752 P.N. 661-0019 P.N. 631-0197 GROMMET, CAN, BLACK, 1/4 BARB, W/ O-RINGS, BLIND, TEA STAINLESS STEEL FITTING P.N. 210-0030 P.N. 625-0004 FLOW CONDITIONER NOZZLE P.N. 265-0718... -
Page 13: Optional Accessories
OPTIONAL ACCESSORIES SHUT-OFF TOOL FLOW CONTROL TOOL P.N. 316-0005 P.N. 316-0006 SEPARATOR NOZZLE ASSY, PLUGGED, SANITIZING, 4FLVR TWR P.N. 316-0004 P.N. 631-0187 DRAIN TUBING P.N. 030-0017 HOLE TEMPLATE 1/4 90 DEG, BARB, W/ O-RINGS, KIT, COUNTER MOUNT STAINLESS STEEL FITTING INSTALL, SCREWS P.N. - Page 14 SHUT-OFF ASSEMBLY...
- Page 15 SHUT-OFF ASSEMBLY ITEM PART NO DESCRIPTION 319-1206 BRACKET ASSY, VALVES/BACK BLOCKS 220-0051 SCREW, 10-32 X 1”, PHILLIPS SLOT 637-0010 ASSY, VALVE, BACKBLOCK, SFCV 632-0192 WATER/SYRUP LINE ASSY 265-0043 WASHER, STEM 208-0109 O-RING, 2-109 265-0434 BODY, VALVE, MTG, SFCV 208-0110 O-RING, 2-110 265-0448 STEM, BODY, SFCV 256-0030...
- Page 16 ASSEMBLY...
- Page 17 ASSEMBLY ITEM PART NO DESCRIPTION 265-0751 MERCHANDISER, NCD GEN II 510-0031 CABLE EXTENSION, 17" 220-0005 SCREW, 8-32 X .375, PH, TH, SS 645-0497 LED PANEL ASSY, NCD, GEN II 265-0750 BACKSPLASH, NCD GEN II 631-0180 ASSY, ADAPTER NOZZLE, 4FE 632-0191 TUBE ASSY, VALVE TO NOZZLE, WATER, NCD GEN II, BLUE 224-0002 SCREW,8-16 X .375, PLASTITE, PHSL, PHD...
- Page 18 SYRUP & WATER VALVE ASSEMBLY...
- Page 19 SYRUP & WATER VALVE ASSEMBLY ITEM PART NO DESCRIPTION 638-0008 VALVE ASSY, SFCV, SYRUP, 1.5 OZ/SEC 638-0019 VALVE ASSY, SFCV, SODA/WATER, 2.0 OZ/SEC 808-0086 LABEL, S4, VALVE 808-0085 LABEL, S3, VALVE 808-0084 LABEL, S2, VALVE 808-0083 LABEL, S1 VALVE SCREW, 8-16 X .500, PLASTITE, SL, HHD RETAINER, BONNET BONNET, BLACK O-RING, 2-114...