Federal Signal Corporation SMART VECTOR SL Installation And Maintenance Instructions Manual page 4

JP2
Figure 3-4.
ed to position one "Center" to position two and "Right to
position three. The "Fast" (WHT/GRY) input will cause
the SignalMaster to operate at twice the normal speed,
when 12VDC is applied to the input.
B. SignalMaster External Controller.
1. See figure 3-5. Ensure that jumpers JP2
& JP7 are installed as indicated.
2. Refer to table 3-1 and connect the Sig-
nalMaster input wires to the corresponding connections
for the SS2000/SM, SMC16 and SMC56 SignalMaster
controllers.
3-4. PROGRAMMING LED FLASH PATTERNS.
There are three lightbar modes that can be pro-
grammed by the user, via three control input wires.
There are also six available LED flash patterns:
• Random
• Quad Flash alternating 75FPM
• Single Flash alternating 75FPM
• Alternate Flash POD's 1&7 90FPM rear only
• Alternate Flash POD's 1&7 90FPM front and
rear
• Alternate Flash POD's 1&7 with POD 4
90FPM rear only
Three default patterns are assigned to operate in
slide switch positions 1, 2, and 3. They are as follows:
• WHT/ORG - Mode #1 – Single flash
• RED - Mode #2 – Quad flash
• WHT/RED - Mode #3 – Random
To change a flash pattern assigned to a slide switch
perform the following:
JP2
Figure 3-5.
JP7
290A5310-04
JP7
290A5310-05
A. Activate lightbar in the desired slide switch
position. The bar will flash in the current pattern.
B. Momentarily apply 12VDC to the program
input (WHT/BLK). The LED flash pattern will advance
to the next available pattern and the end LED module
in POD #1 will flash the selected pattern number. The
lightbar will stop momentarily, then operate in the
selected pattern. Each time 12VDC is momentarily ap-
plied the pattern number will advance. When the last
available pattern number is reached, the next momen-
tary application of 12 VDC will select the first available
pattern.
C. If patterns assigned to the other mode inputs
are to be changed, apply 12VDC to the desired mode in-
put and repeat the above steps.
3-5. PROGRAMMING SMART POD PATTERNS.
There are three Smart Pod program inputs plus an
OFF position that can be assigned to a slide switch posi-
tion.
1. Off
2. P1
3. P2
4. P3
The Smart Pods are programmable on two levels.
First, each of the program inputs, i.e., P1, P2, and P3,
can be set to do one of eight available patterns. See fig-
ure 3-6. These patterns are selected using dip switches
located on the Smart Pod Controller board. Refer to
J7
8
J8
10 1
Q1 Q2
Q3 Q4
R21 R22 R23 R24
R29 R30 R31
R32
L3 L4
L2 L5
Q7 Q8 Q9 Q10
R43 R45
R42 R44
R46
R47 R48 L8 R49
L6 L7
L9
O
N
1 6
6 POS SWITCH
-4-
BATT- BATT+
1 1
+
F4 F1
J1 J2
7 J3 1 J4
1 8 1
R1 R2 R3 R4 R5 R6 R7 R8
H1 H2
R13 R14R15 R16 R17 R18 R19 R20
U3
R11 R12
U1
U2
C10
D1
C1
C2 C3 C4 C5 C6 C7 C11
L1
Q11 C12
C13
R25
R34 C15 R35
S1
R33
D2
C14
RN1
Q5
Y1
1
R38 U6 C16
D4
R39
C19
U5
C20
C23
C24
C22
C21 R41
R50 R51 D8 D10
1
S2
RN2
D7 D9 D11
C25 C26
U7
S1
Figure 3-6.
+ -
-
F2 F3
J6
J5
R9 R10
U4
R26 R28
R27
R36
R37
D3
C17
C18
Q6
D5
R40
D6
R52
P1A
P1B 2005325A- R53
1 2
P1C
P2A
FEDERAL SIGNAL CORP.
P2B
P2C UNIVERSITY PARK,IL
P1A
P1B
P1C
P2A
P2B
P2C
S2
290A5310-06