Related Manuals for WAGO 750-610
Summary of Contents for WAGO 750-610
- Page 1 Fieldbus Independent I/O Modules 24 V DC Power Supply/Fuse/Diagn. 750-610 Manual Version 1.0.2...
- Page 2 • General Copyright © 2006 by WAGO Kontakttechnik GmbH & Co. KG All rights reserved. WAGO Kontakttechnik GmbH & Co. KG Hansastraße 27 D-32423 Minden Phone: +49 (0) 571/8 87 – 0 Fax: +49 (0) 571/8 87 – 1 69 E-Mail: info@wago.com...
-
Page 3: Table Of Contents
Symbols ....................5 Number Notation..................5 Safety Notes ..................... 6 Scope ......................6 2 I/O Modules ....................7 System Modules ..................7 2.1.1 750-610 [24 V DC Power Supply/Fuse/Diagn.]........7 2.1.1.1 View....................7 2.1.1.2 Description..................7 2.1.1.3 Display Elements ................8 2.1.1.4... -
Page 4: Important Comments
WAGO Kontakttechnik GmbH & Co. KG declines all liability resulting from improper action and damage to WAGO products and third party products due to non-observance of the information contained in this manual. -
Page 5: Symbols
Routines or advice for efficient use of the device and software optimization. More information References on additional literature, manuals, data sheets and INTERNET pages 1.3 Number Notation Number Code Example Note Decimal normal notation Hexadecimal 0x64 C notation Binary '100' Within ', '0110.0100' Nibble separated with dots WAGO-I/O-SYSTEM 750 I/O Modules... -
Page 6: Safety Notes
(persons, workplace and packing) is well grounded. Avoid touching conductive components, e.g. gold contacts. 1.5 Scope This manual describes the Digital Input Module 750-610 24 V DC Power Supply/Fuse/Diagn. of the modular WAGO-I/O-SYSTEM 750. Handling, assembly and start-up are described in the manual of the Fieldbus Coupler. -
Page 7: O Modules
Fig. 2.1.1-1: Supply Module 750-610 g061000e 2.1.1.2 Description The supply module 750-610 provides DC 24 V field side power to the downstream modules. The power supply is derived from an external source via the 24 V, 0 V and ground (earth) terminals. -
Page 8: Display Elements
The maximum current of the supply module is 6.3 A. When configuring the system it is important not to exceed the maximum/sum current. However, if such a case should occur, another supply module must be added. The supply module 750-610 can be used with all couplers/controllers of the WAGO-I/O-SYSTEM 750. Attention The supplementary power supply regulations (chapter 2.1.1.7, “Power supply... -
Page 9: Schematic Diagram
750-610 [24 V DC Power Supply/Fuse/Diagn.] • 9 Schematic Diagram 2.1.1.4 Schematic Diagram 750-610 Fig. 2.1.1-3: Supply Module 750-610 g061001e WAGO-I/O-SYSTEM 750 I/O Modules... -
Page 10: Technical Data
10 • 750-610 [24 V DC Power Supply/Fuse/Diagn.] Technical Data 2.1.1.5 Technical Data Module Specific Data Voltage via power jumper contacts DC 24 V (-25 % ... +30 %) Current via power jumper contacts 6.3 A max. Supply voltage detection level on: >... -
Page 11: Process Image
• 11 Process Image More Information Detailed references to the approvals are listed in the document "Overview Approvals WAGO-I/O-SYSTEM 750", which you can find on the CD ROM ELECTRONICC Tools and Docs (Item-No.: 0888-0412) or in the internet under: www.wago.com... - Page 12 12 • 750-610 [24 V DC Power Supply/Fuse/Diagn.] Power supply concept I/O Modules Fieldbus Coupler/ (610) (601) Controller (601) (602) Field 230V Field Field Electronic Field Potential 1 Potential 3 Potential 2 Fig. 2.1.1-4: Power supply concept g060203e WAGO-I/O-SYSTEM 750...
- Page 13 750-610 [24 V DC Power Supply/Fuse/Diagn.] • 13 Power supply concept WAGO-I/O-SYSTEM 750 I/O Modules...
- Page 14 WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D-32385 Minden Hansastraße 27 • D-32423 Minden Phone: 05 71/8 87 – 0 Fax: 05 71/8 87 – 1 69 E-Mail: info@wago.com Internet: http://www.wago.com...