Table of Contents
Advertisement
Quick Links
P R O B L E M S O LV E D
Installation and Operation Manual
Switcher/Router with Mechanical Latching Relays
If you need a firmware upgrade, contact Broadcast Tools®
No part of this document may be reproduced or distributed without permission.
ALL SPECIFICATIONS AND FEATURES FOR THIS PRODUCT ARE SUBJECT TO
NOTE: We recommend the use of Chrome, Firefox or Safari as your browser.
Due to the dynamic nature of product design, the information contained in this
document is subject to change without notice. Broadcast Tools, Inc., assumes no
responsibility for errors and/or omissions contained in this document. Revisions
of this information or new editions may be issued to incorporate such changes.
Broadcast Tools® is a registered trademark of Broadcast Tools, Inc.
tiny TOOLS™ is a trademark of Broadcast Tools, Inc.
All Sentinel® labeled products are registered trademarks of Broadcast Tools, Inc.
Copyright® 1989 - 2012 by Broadcast Tools, Inc. All rights reserved.
No part of this document may be reproduced or distributed without permission.
Visit www.broadcasttools.com for important product update information.
SS 2.1 MLR/BNC
Manual update: 09/04/2012
CHANGE WITHOUT NOTICE
®
Advertisement
Table of Contents
Related Manuals for Broadcast Tools SS 2.1 BNC
Summary of Contents for Broadcast Tools SS 2.1 BNC
- Page 1 NOTE: We recommend the use of Chrome, Firefox or Safari as your browser. Due to the dynamic nature of product design, the information contained in this document is subject to change without notice. Broadcast Tools, Inc., assumes no responsibility for errors and/or omissions contained in this document. Revisions of this information or new editions may be issued to incorporate such changes.
-
Page 2: Table Of Contents
SS 2.1 MLR/BNC Installation and Operation Manual Table of Contents Section Title ........Page # Introduction. -
Page 3: Introduction
SS 2.1 MLR/BNC Installation and Operation Manual INTRODUCTION CAUTION! Thank you for your purchase of a BROADCAST TOOLS® SS 2.1 MLR/BNC trans- parent two input, dual output switcher/router (referred to as the SS 2.1 MLR/BNC Broadcast Tools® throughout this manual). We’re confident that this product will give you many years Products, as with any of dependable service. -
Page 4: Introduction
SS 2.1 MLR/BNC Installation and Operation Manual Product Overview The SS 2.1 MLR/BNC is a transparent two input, dual output switcher/router with mechanical latching relays and BNC connectors. The SS 2.1 MLR/BNC is perfect for all types of passive signal switching via front panel switches, contact closures and/or serial RS-232. -
Page 5: Inspection
SS 2.1 MLR/BNC Installation and Operation Manual Inspection Please examine your SS 2.1 MLR/BNC carefully for any damage that may have been sustained during shipping. If any damage is present, please notify the ship- per immediately and retain the packaging for inspection by the shipper. The pack- age should contain the SS 2.1 MLR/BNC, a modular cable with 9-pin “S9”... -
Page 6: I/O And Remote Control Connectors
SS 2.1 MLR/BNC Installation and Operation Manual I/O and Remote Control Connectors CAUTION! The rear panel contains BNC connectors for I/O and removable screw terminals for remote control interfacing with mating connectors. The multi-drop serial port is Installation of the SS 2.1 equipped with a modular RJ-11 jack. -
Page 7: Configuration Dip-Switch Setup
SS 2.1 MLR/BNC Installation and Operation Manual Configuration DIP-switch Setup Follow the tables below for configuration options. Unit ID SW5-1 SW5-2 ID 0 * ID 1 ID 2 ID 3 Baud Rate SW5-3 SW5-4 2400 9600 * 19200 38400 Power Up SW5-5 User selected Last source selected* OFF... -
Page 8: Serial Commands
Accesses the menu. (NOTE: The menu times out after 60 seconds of keyboard inactivity). Menu Operation Broadcast Tools® SS 2.1MLR BNC, v1.9b - Setup Menu S - Turn ON audio input M - Turn OFF audio V - Save Audio State for Power Up... -
Page 9: Specifications
SS 2.1 MLR/BNC Installation and Operation Manual SPECIFICATIONS Inputs/Outputs: Any input level and impedance can be used. Inputs may be balanced or unbalanced. Output levels, impedance, distor- tion, noise and balancing will match that of the selected input. Switching Method: Passive. -
Page 10: Warranty
If Broadcast Tools is notified, in writing, of a failure of any item manufactured by Broadcast Tools to conform to the foregoing Limited Warranty within one (1) year following the date of the Buyer’s acquisition of the item, and if the item is returned to Broadcast Tools in accordance with Broadcast Tools’... - Page 11 SS 2.1 MLR/BNC Installation and Operation Manual FRONT PANEL REAR PANEL APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
- Page 12 SS 2.1 MLR/BNC Installation and Operation Manual APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
- Page 13 SS 2.1 MLR/BNC Installation and Operation Manual APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
- Page 14 SS 2.1 MLR/BNC Installation and Operation Manual APPENDIX e-mail: voice: fax: support@broadcasttools.com 360.854.9559 866.783.1742...
Need help?
Do you have a question about the SS 2.1 BNC and is the answer not in the manual?
Questions and answers