Table of Contents
Advertisement
Quick Links
Series 7.2 - Adjustable Height Tables
®
Tools required:
Power Drill
#2 SQUARE
DRIVE BIT
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©
2015 Steelcase Inc.
Grand Rapids, MI 49501
Page 1 of 20
U.S.A.
18719901 Rev G
Printed in U.S.A.
Advertisement
Table of Contents
Related Manuals for Steelcase 7.2 Series
Summary of Contents for Steelcase 7.2 Series
- Page 1 #2 SQUARE DRIVE BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S.
- Page 2 ® IMPORTANT SAFETY INSTRUCTIONS When using an electrical furnishing, basic precautions should always be followed, including the following: Read all instructions before using (this furnishing). DANGER - To reduce the risk of electric shock: 1. Always unplug this furnishing from the electrical outlet before cleaning. WARNING - To reduce the risk of burns, fire, electric shock, or injury to persons: 1.
-
Page 3: Table Of Contents
® TABLE OF CONTENTS: PAGE(S): Lets Get Started!.................... Attaching Stretchers..................Mounting Legs to Worksurface..............6 & 7 Attaching Control Box & Wire Managers............8 & 9 Connecting & Routing Cables................ 10 & 11 Attaching the Controller................. 12 & 13 Finishing the Leg Installation................. 15 &... -
Page 4: Lets Get Started
® Let's Get Started! Assembling a 90 corner table with a 2-piece worksurface? Prepare a large open space to assemble the table. Jump to Appendix 'A' now. • Sweep the floor! Screws and small parts can damage the worksurface. • Put down a CLEAN shipping blanket to protect the worksurface. Unpack the worksurface and place on the shipping blanket upside-down. -
Page 5: Attaching Stretchers
Attaching Stretchers ® STRETCHER Layout the left and right stretcher assembly and the center connector with the dovetails pointing down. Loosely install the center connector to the left and right stretcher using two (2) 1/4-20 type F flat head screws with phillips #3 drive...do not tighten. -
Page 6: Mounting Legs To Worksurface
® Mounting Legs to Worksurfaces For 2-Leg Tables: MOTOR HOUSING IS ALWAYS AT FRONT OF LEG With the top still upside down on the floor, turn the base over (flipping is a 2 person job), and align the attachment plates to the pre-drilled holes in the top. Loosely install one fastener in each of the pre-drilled pilot holes. - Page 7 Mounting Legs to Worksurfaces (cont.) ® For 3-Leg Tables: With the top still upside down on the floor, turn the base over (flipping is a 2 person job), and align the attachment plates to the pre-drilled holes in the top. For 3-leg tables, align the center lifting column first.
-
Page 8: Attaching Control Box & Wire Managers
Attaching Control Box & Wire Managers ® Install control box in the predetermined location, using pre-drilled holes. CONTROL BOX Install the wire managers to the underside of the worksurface. Be sure to allow space for wires to bend gently without getting kinked, and space for accessories to clamp onto the back edge of the worksurface. - Page 9 Attaching Control Box & Wire Managers (cont.) ® For 3-leg tables, place one wire manager on each side of the table. Install the wire WIRE MANAGER managers to the underside of the worksurface as shown. Be sure to allow space for wires to bend gently without getting kinked, and space for accessories to clamp onto the back edges of the worksurface.
-
Page 10: Connecting & Routing Cables
Connecting & Routing Cables ® For 2-Leg Tables: Connect the cables to each lifting column and connect the terminal end to the control box. Route these cables in the wire management cableway provided. Refer to the Wiring Guide for more information on page 18. For optimal wire management, connect lifting columns to the closest port on the control box. - Page 11 Connecting & Routing Cables (cont.) ® For 3-Leg Tables: Connect the cables to each of the three lifting columns and connect the terminal end to the control box. Route these cables in the wire management cableway provided. (2000mm cables to the left and right lifting columns &...
-
Page 12: Attaching The Controller
Attaching the Controller ® Install the controller to the underside of the worksurface on the side preferred by the user. (We recommend it be placed toward the outside of the table to avoid interference in the workspace.) Push Button Stick-On Controller NOTE: Push button stick-on controller installation is shown here. - Page 13 Attaching the Controller (cont.) ® PAPER BACKING Install the wire keepers for the control wire. Peel off paper WIRE KEEPER backing and stick to worksurface. Place wire into each wire keeper. CONTROL WIRE Page 13 of 20 18719901 Rev G...
-
Page 14: Finishing The Leg Installation
Finishing the Leg Installation ® SQUARE DRIVE SCREW Plug unit in and check for binding, by running the table base all the way through its range of motion and back again, then lower to bottom and unplug unit. Install the remaining fasteners in each of the remaining holes and tighten ALL screws securely. -
Page 15: Finishing The Table Assembly
Finishing the Table Assembly ® Carefully turn the table over (2 person operation). Connect power cord to power supply. NOTE: Do NOT use either lifting column as a brace CAUTION: Be sure to create a 'drip loop' in the when turning the table over, as thismay cause binding. power cord before making the connection to a live wall socket, to prevent electric shock if The top must be lifted free, rotated, and set down... - Page 16 Finishing the Table Assembly (cont.) ® Before use, the table must be completely leveled, Before articulation, you front-to-back and side-to-side using the height must synchronize the adjustable glides. Failure to do this lifting columns as could cause the lifting outlined below. columns to bind.
-
Page 17: Guidelines On Moving The Table
® Guidelines on Moving the Table When possible, the table should be moved in a horizontal (flat) position. If the table must be moved vertically (i.e. standing on a pallet), care must be taken to ensure no side pressure is placed on any of the lifting columns as it is tipped into position, during transport, and when tipped off the pallet at the new location. -
Page 18: Wiring Guide
Once you have completed the wiring, use the Wire Managers to hold all the FOOT cables and minimize possible entanglements. GLIDES RIGHT LIFTING NOTE: Vertical wire management solutions are also available from Details. COLUMN Contact your local dealer or Steelcase.com for more information. CONTROL ATTACHMENT PLATE LEFT LIFTING COLUMN CONTROLLER... -
Page 19: Appendix A: 2-Piece Worksurface Assembly
Appendix A: 2-Piece Worksurface Assembly ® Position top pieces upside down on the assembly surface and align with wood spline (or biscuits) provided. Optional Biscuits SPLINE DRAW BOLTS SCREWS V-CHANNELS Install draw bolts and tighten with 5/16" or 7/16" open end wrench. - Page 20 Appendix A: 2-Piece Worksurface Assembly (cont.) ® Special Notes on 2-Piece Worksurfaces Overhangs: • The extension portion of 2-piece worksurfaces may not completely overhang the supporting leg! • One leg must always be fully mounted to the extension portion. CORRECT! CORRECT! WRONG! THIS CONDITION...
Need help?
Do you have a question about the 7.2 Series and is the answer not in the manual?
Questions and answers