CHIEF PNRIW Series Installation Instructions Manual
Large flat panel in-wall swing arm mount
Hide thumbs
Also See for PNRIW Series:
- Installation instructions manual (8 pages) ,
- Installation instructions manual (13 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CHIEF PNRIW Series
Summary of Contents for CHIEF PNRIW Series
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S Large Flat Panel In-Wall Swing Arm Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description PNRIW Series...
-
Page 2: Important Safety Instructions
The PNRIW mounts are designed to be ACCESSORY: AN ACCESSORY is the secondary Chief mounted within a Chief Listed PAC501 in-wall enclosure (not product which is attached to a primary Chief product, and may included). have a component attached or setting on it. NOTE: The PNRIW Series includes: •... -
Page 3: Installation Instructions
Installation Instructions PNRIW Series DIMENSIONS NOTE: PSBU INTERFACE BRACKET NOT PNRIW SHOWN IN PAC-501 SHOWN. THE PSBU INTERFACE BRACKET WILL ADD 1” IN DEPTH AND MAY AFFECT WHICH MUST BE ORDERED SEPARATELY LOCATION OF THE DISPLAY ON THE MOUNT. ADDED DEPTH WHEN RETRACTED 30.00... - Page 4 PNRIW Series Installation Instructions DIMENSIONS (CONT’D) DIMENSIONS: [MILLIMETERS] INCHES LEGEND Hex-Head Wrench Tighten Fastener Apretar elemento de fijación Llave de cabeza hexagonal Befestigungsteil festziehen Sechskantschlüssel Chave de cabeça sextavada Apertar fixador Chiave esagonale Serrare il fissaggio Bevestiging vastdraaien Zeskantsleutel Serrez les fixations Clé...
- Page 5 Installation Instructions PNRIW Series TOOLS REQUIRED FOR INSTALLATION AND PARTS (9/16") (3/16") A (1) B (4) [Swing arm mount assembly] [Trim - 2 short (SIDES) - 2 long] C (4) E (4) D (4) 5/16-18 x 5/8" 5/16" 5/16" F (16)
- Page 6 PNRIW Series Installation Instructions INSTALLATION The following procedure assumes that a Chief Listed Model PAC501 In-Wall accessory has previously been installed using the installation instructions and hardware provided with the PAC501. If a PAC501 is not installed or there are any other questions regarding the installation of this accessory, immediately contact a Chief Customer Service representative.
-
Page 7: Display Installation
If an interface bracket is not installed or there are any other questions regarding the installation of the display, immediately contact a Chief Remove pin Customer Service representative. -
Page 8: Cable Management
PNRIW Series Installation Instructions Cable Management (Optional) Install two cable clips (P) into holes on connector bracket. (See Figure 7) Attach all cables to display. If necessary, use cable tie mounts (G) and cable ties (M) to (top view) secure cables within PAC501. -
Page 9: Tension Adjustments
Installation Instructions PNRIW Series Tension Adjustments Roll Tension Adjustment Pitch Tension Adjustment With display mounted, check for desired Pitch tension. CAUTION: IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TO If required, adjust the Centris Select knob right or left until EQUIPMENT! Over tightening roll tension adjustment will desired pitch tension is obtained. - Page 10 PNRIW Series Installation Instructions Swivel Tension Adjustment Swing Arm Tension Adjustment Swing arm tension is pre-set at the factory and is adjusted to accommodate displays with weights near the top of the mount’s capacity. CAUTION: DO NOT OVER TIGHTEN SWIVEL If smaller displays are used it may be difficult to reposition the ADJUSTMENT NUT.
-
Page 11: Removing Display From Mount
Installation Instructions PNRIW Series Use the adjustment wrench (L) provided with the mount, Pull back on flag on upper mounting hole and press pin and turn adjustment insert clockwise to increase swing arm down into "Open" position. (See Figure 14) tension (See Figure 13) or counterclockwise to reduce swing arm tension. - Page 12 F 877.894.6918 / 952.894.6918 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 Chief, a products division of F +31 (0) 495 580 845 Milestone AV Technologies Asia Pacific A Office No. 918 on 9/F, Shatin Galleria...
Need help?
Do you have a question about the PNRIW Series and is the answer not in the manual?
Questions and answers