Related Manuals for Krone EasyCut B 870 CV Collect
Summary of Contents for Krone EasyCut B 870 CV Collect
- Page 1 Original Operating Instructions Document no.: 150000707_01_en Mower Combination EasyCut B 870 CV Collect From machine no.: 976393...
- Page 2 Contact Maschinenfabrik Bernard Krone GmbH & Co. KG Heinrich-Krone-Straße 10 48480 Spelle Germany Telephone switchboard + 49 (0) 59 77/935-0 Telefax switchboard + 49 (0) 59 77/935-339 Telefax spare parts warehouse do- + 49 (0) 59 77/935-239 mestic Telefax spare parts warehouse export + 49 (0) 59 77/935-359 Internet www.landmaschinen.krone.de...
-
Page 3: Table Of Contents
Pole protection mechanism ....................... 34 Technical data .......................... 35 Consumables .......................... 36 4.1.1 Oils............................. 36 4.1.2 Lubricating greases ........................ 36 Control and Display Elements .................... 37 Operation panel ......................... 37 Initial operation ........................ 39 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 4 Deviating tightening torques ...................... 77 11.4 Strip on the cross conveyor belt .................... 77 11.5 Cleaning cross conveyor belts .................... 77 11.6 Venting the friction clutch...................... 78 11.7 Checking guard cloths ....................... 79 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 5 Lubricating universal shaft ...................... 96 15.2 Lubrication chart - Machine ....................... 97 Storage............................ 100 Waste disposal........................ 102 Appendix .......................... 103 18.1 Circuit diagram......................... 103 Index............................ 115 Declaration of conformity ..................... 121 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 6: Information On This Document
Validity This document is valid for machines of type: EasyCut B 870 CV Collect This document only describes the rear combination. If the combination is used with front mounted mower, the operating instructions of the front mounted mower must also be considered. -
Page 7: Figures
This bullet point identifies an enumeration. If the bullet point is intended, it identifies the second level of the enumeration. Icons in figures The following icons can be used in illustrations: EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 8 CAUTION The signal word CAUTION warns of a hazardous situation which will result in minor to moderate injuries if the warning sign is ignored. Example of a warning sign: EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 9: Conversion Table
Litres per minute L/min 0.2642 US gallons per minute Cubic metres m³/h 4.4029 per hour Force Newton 0.2248 Pound force Length Millimetre 0.03937 Inch Metre 3.2808 Foot Power Kilowatt 1.3410 Horsepower EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 10 0.6215 Miles per hour hour Volumes Litres 0.2642 US gallon US gal. Millilitre 0.0338 US ounce US oz. Cubic centi- cm³ 0.0610 Cubic inch in³ metre Weight Kilogram 2.2046 Pound EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 11 Information on This Document How to use this document This page has been left blank deliberately. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 12: Safety
• Attachment of unauthorised or unapproved additional equipment • Use of spare parts which are not KRONE original spare parts • Stationary operation of the machine Unauthorised modifications to the machine may affect the properties of the machine or disrupt proper operation. -
Page 13: Service Life Of The Machine
He has read the operating instructions and can implement the information in the operating instructions accordingly. • He is familiar with driving vehicles safely. • For road travel he has adequate knowledge of the highway code and has the stipulated driving licence. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 14: Personnel Qualification Of The Technicians
„ To ensure operational safety, use original parts or standard parts which correspond to the requirements of the manufacturer. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 15: Jobs On The Machine
„ Immediately eliminate potential causes of damage, for example heavy soiling, or tighten slack screws. „ In case of damage which may affect operational safety and cannot be repaired according to these operating instructions: Have damage repaired by a qualified service centre. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 16: Danger Zones
„ Ensure sufficient overlap of section tube and universal shaft guards. „ Make sure that the universal shaft guards are mounted and that they are fully functional. „ Allow the universal shaft locks to engage. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 17 „ In case of dangerous situations, immediately switch off drives and instruct persons to leave the danger zone. Danger zone due to trailing machine parts If machine parts are trailing, people may be seriously injured or killed. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 18: Ensuring Functionality Of Safety Devices
„ Make sure every time after cleaning the safety labels that they are complete and legible. „ Immediately replace missing, damaged and unrecognizable safety labels. „ Provide spare parts with intended safety labels. Descriptions, explanations and order numbers of safety labels,refer to page 25. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 19: Road Safety
„ Do not park the machine on slopes. „ Observe procedures for operating the machine on slopes, refer to page 56. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 20: Parking The Machine Safely
„ Check and clean the machine every day before using it for the first time. „ Check and clean the machine regularly during the working day. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 21: Sources Of Danger On The Machine
„ Specify rules for the use of hearing protection and for the working time. „ During operation keep windows and doors of cabin closed. „ Remove hearing protection for road travel. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 22 • Mower gearbox • Belt gearbox • Hydraulic system • Cutter bar „ Maintain a sufficient distance from hot surfaces. „ Leave machine parts to cool down and wear protective gloves. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 23: Dangers In Connection With Certain Activities: Working On The Machine
Frame or supporting components • Running gear „ Before carrying out welding work on the machine, obtain consent by KRONE customer service and, if required, identify alternatives. „ Before performing welding work on the machine, park the machine safely and disconnect it from the tractor. -
Page 24: Behaviour In Dangerous Situations And In Case Of Accidents
„ Before working on or under raised machine parts: Secure machine or machine parts against lowering by means of hydraulic shut-off device (e.g. stop cock) on machine side. „ Before working on or under raised machine parts: Safely support machine or machine parts. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 25: Carrying Out Oil Level Check And Oil And Filter Element Changes Safely
Safety Labels on the Machine Every safety label is provided with an order number and can be ordered directly from the authorised KRONE dealer. Immediately replace missing, damaged and unrecognisable safety labels. When attaching safety labels, the contact surface on the machine must be clean and free of dirt, oil and grease to ensure optimum adhesion of the labels. - Page 26 Safety Safety Labels on the Machine Position and meaning of safety labels KMG000-046 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 27 If the maximum permitted operating pressure is exceeded, hydraulic parts may be dam- aged. As a result, people may be seriously or fatally injured. „ Observe the permitted PTO speed. „ Observe the permitted operating pressure. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 28 Danger from rotating machine parts When approaching the danger zone, there is a danger of being drawn in from rotating ma- chine parts. „ Keep sufficient distance from rotating machine parts. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 29 „ To avoid that functions are triggered by mistake, the regulating valves of the tractor must be in neutral position and locked during road transport journeys. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 30: Safety Equipment
Overload protection • The overload protection protects the tractor and the machine from load peaks „ To avoid damaging the machine, switch off the PTO shaft if the overload clutch engages continuously. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 31: Smv Emblem
The SMV emblem (1) is at the rear in the centre or on left. If the machine is transported on transport vehicles (for example lorry or train), the SMV emblem must be covered or dismounted. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 32: Machine Description
Tine rotor Impact damage protection system Hydraulic oil tank Universally-jointed drive shaft Cross conveyor Spare blade drawer Cross conveyor belt Main gearbox Conveyor belt Cutterbar Side guard Mower gearbox Document storage tube EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 33: Labelling
(3). Intermediate universal shaft To ensure the functionality and to increase the lifetime, the friction clutch must be vented once a year before the beginning of the season, refer to page 78. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 34: Pole Protection Mechanism
The impact damage protection system engages again as soon as the mower is moved back. The trigger moment is factory preset. Dimension X =85 mm EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 35: Technical Data
Number of cross conveyor belts 2 units Mechanical spring relief 80 mm Ambient temperature Temperature range for machine operation -5 to +45°C Airborne noise emission Equivalent continuous sound pressure level >85 dB(A) EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 36: Consumables
51818 of NLGI class 2, Li soap with EP additives Lubricate the manual lubrication point until grease escapes at the bearing position. After lubricating, remove the grease escaping from the bearing position. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 37: Control And Display Elements
Raises the right mower from working position to headland position. Double-acting control unit (1+/1-): (1-) Lowers the left mower from headland position to working position. (1+) Raises the left mower from working position to head- land position. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 38 The rotary potentiometer is used to adjust the speed of the cross conveyor belts. Turn clockwise = increase the speed of the cross conveyor belts Turn counter-clockwise = reduce the speed of the cross conveyor belts EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 39: Initial Operation
ü The conveyor belts have been set and the running behaviour has been checked, refer to page 68. ü The limit switch “Cross conveyor bottom” is set, refer to page 40. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 40: Setting The Limit Switch "Cross Conveyor Bottom
„ Loosen the screws (2). „ Move the limit switch (1) in the oblong hole until it switches (click sound). „ Tighten screws (2). „ Check limit switch (1). EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 41: Adapting Coupling Points
„ Secure the lower link pins (1) with the linch pin (4) and the safety chain (5). Top link pin The top link pin (1) is designed for category II and III. KM000-107 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 42: Adapting Universal Shaft
(shift length) of the profile tubes and guard tubes of at least 200 mm, refer to the operating instructions of the universal shaft manufacturer. „ Check the overlap of profile tubes and guard tubes. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 43: Check Cross Conveyors For Firm Attachment
„ Lower the cross conveyor belt from a safe distance by short intervals until hydraulic oil escapes bubble-free. „ Shut down and safeguard the machine, refer to page 24. „ Unscrew the connecting piece. „ Repeat the process for all 4 Minimess connections. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 44: Start-Up
Even with a fitted rear-mounted device, the front axle of the tractor must always be loaded with a minimum 20% tare weight of the tractor. „ Make sure before starting to move that these requirements have been met. KMG000-012 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 45: Connecting Hydraulic Hoses
Short circuit caused by impurities and moisture in the plug connection The machine may be damaged by a short circuit. „ Make sure that the plugs and sockets are clean and dry. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 46: Connecting Road Travel Lighting
Short circuit caused by impurities and moisture in the plug connection The machine may be damaged by a short circuit. „ Make sure that the plugs and sockets are clean and dry. KMG000-013 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 47: Installing Universal Shaft
„ Check the tine conditioner for bent and damaged tines each time before it is used. „ To prevent the loss of tines, check the bearing bolts of the tine bearings and replace them in time. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 48 ü The machine is in the working position, refer to page 53. ü The machine is shut down and safeguarded, refer to page 24. „ Dismount bent and damaged tines (1). „ Adjust and mount bent tines. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 49: Operation
If the front guard is folded up during work, objects can be ejected. As a result, people may be seriously injured. „ Fold down the front guard. „ Connect the guard cloths of the front guard and the side guard using the turnlock fasteners. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 50: Folding Up The Front Guard
ü The machine is in the working position, refer to page 53. ü The machine is shut down and safeguarded, refer to page 24. „ Fold down the front guard (1). „ Close the turnlock fasteners (3). EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 51: Side Guard
ü The machine is shut down and safeguarded, refer to page 24. „ Fold down the side guard (1). „ Ensure that the side guard (1) is secured by the locking, refer to page 64. „ Close the turnlock fasteners (2). EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 52: Operate The Support Jack
„ Pull the bolt (1), push the front support jack (2) downwards and lock it by using the bolt (1). „ Pull the tension bar (4), swivel the rear support jack (3) downwards and lock it by using the tension bar (4). EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 53: Locking / Releasing Stop Cocks
„ Move toggle switch (3) to “centre” position. „ Actuate control unit (2-) until both mowers are lowered into working position. „ To mow, move control unit (2-) to float position. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 54 „ To increase the speed, turn the rotary potentiometer (4) to the right. Reducing: „ To reduce the speed, turn the rotary potentiometer (4) to the left. From headland position to transport position ü The PTO shaft drive is switched off. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 55: Mowing
The front mounted mower alone can be used to mow small plots of crops or narrow sections in open fields. In doing so, the lateral mowers must be in the transport position. INFORMATION Leave the control units in the float position while mowing. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 56: Field Mode On Slopes
KMG000-094 „ Do not move the machine from transport into working position or from working into transport position as long as the machine is operated diagonal to the slope. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 57: Driving And Transport
Even with a fitted rear-mounted device, the front axle of the tractor must always be loaded with a minimum 20% tare weight of the tractor. „ Make sure before starting to move that these requirements have been met. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 58: Prepare The Machine For Road Travel
„ Raise the machine until the support jacks (5) can be swivelled down. „ Swivel down the front and rear support jacks (5) and secure them with the bolt (4), refer to page 52. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 59 To save space, the machine can also be parked with mowers folded up. To prevent the machine from overturning, park it on firm ground. „ Only park the machine on level ground capable of bearing the load such as concrete or asphalt. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 60: Settings
ð Top link shorter = smaller cutting height „ Swivel the support jack/(s) up, refer to page 52. For version with “high-cut skids” The cutting height can be increased by means of high-cut skids. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 61: Setting The Lateral Links
People may be seriously injured or killed as a result. „ Never unscrew the threaded spindles (2) of the relief springs (1) further than the dimension X = 80 mm. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 62: Increasing/Reducing Ground Pressure
„ To increase the ground pressure, increase the dimension X. „ To reduce the ground pressure, reduce the dimension X. „ Tighten the counter nut (5). Set the dimension X in the same way on all relief springs. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 63: Setting The Side Guards
„ To reduce the ground pressure, reduce the dimension X. „ Tighten the counter nut (5). „ Set the dimension X in the same way on all relief springs. 10.5 Setting the side guards KMG000-078 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 64: Checking/Setting Locking Of Side Guards
„ Move the machine to the transport position. ð If the side guard folds down, the side guard is correctly adjusted. ð If the side guard does not fold down, the lock must be adjusted. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 65: Setting The Conditioner Speed
„ Turn the actuating lever (2) 180 degrees. INFO: To turn the actuating lever more easily, turn the mower drum manually. „ Secure the actuating lever (2) with the wing screw (1). 10.8 Setting the degree of conditioning KMG000-066 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 66: Setting Wide Spreading
The degree of conditioning is increased. Æ In the "-" direction: The distance between the tines and the conditioning sheet is increased. The degree of conditioning is reduced. 10.9 Setting wide spreading KM000-030 [ECB00049] EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 67: Setting Widespreading Sheet
„ Loosen the palm knobs (1) on right-hand and left-hand machine side. „ Move the widespreading sheet (2) to the desired position. In case of swathing, the widespreading sheet must be set completely down. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 68: Setting Conveyor Belt
„ Loosen the counter nuts (5) of the clamping screws (4) at position (III) and (IV). „ To relieve the conveyor belt, loosen the clamping screws (4) at position (III) and (IV). EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 69 The conveyor belt runs upwards over the drive roller (1): „ Loosen the position (III) and retighten the position (IV). The conveyor belt runs downwards over the drive roller (1): „ Loosen the position (IV) and retighten the position (III). EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 70: Moving Cross Conveyors
When the accelerator roller (1) is used, move the cross conveyor belt (3) so that the accelerator roller (1) is outside the conditioner (2). ü The machine is in the working position, refer to page 53. ü The machine is shut down and safeguarded, refer to page 24. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 71 „ Pull the lever (4) downwards and hold it. „ Adjust the lever (4). Æ In the “-” direction: Increase the swath width. Æ In the direction “+”: Reduce the swath width. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 72: Maintenance - General Information
Main gearbox refer to page 84 Cutterbar refer to page 94 Components Changing/replacing blades refer to page 88 Check/replace cutting discs/mower drums refer to page 92 Check/replace retaining bolt (blade screw con- refer to page 91 nection) EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 73: Maintenance - Every 10 Hours, But At Least Once A Day
Maintenance - Every 50 hours Components Tighten screws/nuts on the machine refer to page 74 11.1.5 Maintenance - Every 200 hours Changing oil Input gearbox refer to page 83 Main gearbox refer to page 84 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 74: Maintenance - Every 500 Hours
The table does not apply to countersunk screws with hexagon socket in case the countersunk screw is tightened via hexagon socket. DV000-001 Thread size Strength class on screw head Strength class 10.9 12.9 Tightening torque (Nm) EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 75 M30 x 1.5 2,100 2,650 Metric thread screws with countersunk head and hexagon socket INFORMATION The table applies only to countersunk screws with hexagon socket and metric thread tightened via hexagon socket. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 76 Ventilation and breather filter made of Ventilation/breather filter made of brass steel Steel and cast Aluminium Steel and cast Aluminium Maximum tightening torque (Nm) (±10 %) M10x1 M12 x 1.5 G1/4“ M14 x 1.5 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 77: Deviating Tightening Torques
Strip on the cross conveyor belt KM000-062 11.5 Cleaning cross conveyor belts INFORMATION Only clean the cross conveyor belts with low pressure and much water. Never use detergents. Lubricate the bearing points after cleaning. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 78: Venting The Friction Clutch
„ Never intervene in the overload protection. „ Only use KRONE original spare parts. The friction clutch protects the tractor and the machine from damage. The friction clutch must be vented before starting up for the first time and once a year. The friction clutch is designed with a permanently adjusted turning torque M . -
Page 79: Checking Guard Cloths
„ Carry out a visual inspection of the guard cloth (1) to ensure that there are no cracks and damage. Æ The machine can be used when there are no cracks or damages. Æ Replace guard cloths in case of cracks or damage. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 80: Maintenance - Hydraulic System
The on-board hydraulic system of the machine is supplied with pressure by an own hydraulic pump (1). The hydraulic pump (1) is connected to the lower part of the main gearbox by a flange and requires no maintenance. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 81: Hydraulic Oil Tank
„ Unscrew the oil drain plug (2) and drain the oil. „ Screw in the drain plug (2), tightening torque refer to page 76. „ Fill in new oil through the filling hole. „ Check the oil level. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 82 „ Remove the filter element (2) and dispose of it properly. „ Wet sealing surface of new filter element (2) with oil and insert it. „ Unscrew the cover (1) and tighten it. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 83: Maintenance - Gearbox
„ Refill with fresh oil up to the inspection hole (1) via the filling hole (3). „ Screw on the locking screw of the inspection hole (1) and the locking screw of the filling hole (3), tightening torque refer to page 76. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 84: Main Gearbox
„ Refill with fresh oil up to the inspection hole (1) via the filling hole (3). „ Screw on the locking screw of the inspection hole (1) and the locking screw of the filling hole (3), tightening torque refer to page 76. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 85 „ Refill with fresh oil up to the inspection hole (1) via the filling hole (3). „ Screw the locking screw into the inspection hole (1) and the locking screw into the filling hole (3), tightening torque refer to page 76. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 86: Maintenance - Cutterbar
The nuts (2) with left-handed thread (LH) have distinctive grooves (a) on the bevel. • The pinion shafts (4) with left-handed thread (LH) have a distinctive groove (b) on the face. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 87: Replacing The Shear Bolt At The Rotary Hub
„ Dismount the nut (2) by using the special key (10) included with delivery. „ Dismount the hub (1). „ Remove the damaged shear pins (3). „ Check the nut and the hub for damage. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 88: Check/Change Blades
Maintenance - Cutterbar 14.3 Check/change blades INFO : Replace damaged parts by KRONE original spare parts. „ Fill the space above the bearing with grease (c). „ Place the hub on the pinion shaft. INFO : Observe the position of the shear pins. The slots of the shear pins (3) must be mounted facing each other horizontally, see detail (I). -
Page 89: Changing Blades For The "Blade Screw Connection" Version
„ Insert the new blade (5) between the wear skid (2) and the cutting disc (1). „ Insert the retaining bolt (3) from below through the wear skid (2), the blade (5) and the cutting disc (1). EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 90: Changing Blades For The "Blade Quick Fastener" Version
„ Repeat the process for all blades. „ Fold down the front guard. INFORMATION Clockwise rotating blades can be ordered by stating order number 00 139 889 *. Anticlockwise rotating blades can be ordered by stating order number 00 139 888 *. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 91: Checking/Replacing Retaining Bolts
„ The blade carriers must be replaced at the latest when the application seam (1) is worn at one point. „ The blade carriers must only be replaced by KRONE original spare parts. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 92: Checking/Replacing Cutting Discs/Mower Drums
„ If cutting discs/mower drums are deformed, the dimension X=48 mm must not be exceeded. „ The cutting discs/mower drums must only be replaced by KRONE original spare parts. KM000-042 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 93: Checking The Wear Limit On Cutting Discs/Mower Drums
„ The cutting discs/mower drums must be replaced at the latest when the material thickness is below the minimum material thickness of 3 mm. „ The cutting discs/mower drums must only be replaced by KRONE original spare parts. KM000-043 14.7... -
Page 94: Checking Oil Level
There is no need to change the oil on the cutterbar. Before checking the oil level on the cutterbar, the cutterbar must be aligned levelly by means of a spirit level. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 95 If the oil does not reach the inspection hole (1): „ Top up new oil via the inspection hole (1) up to the inspection hole (1). „ Mount the locking screw of the inspection hole (1),refer to page 76. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 96: Maintenance - Lubrication
ü The machine is shut down and safeguarded, refer to page 24. „ Observe operating instructions of the universal shaft manufacturer. „ Lubricate the universal shaft with multi-purpose grease at the intervals indicated in the figure. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 97: Lubrication Chart - Machine
The types of lubrication are marked by means of icons in the lubrication chart, refer to table. Type of lubrication Lubricant Comment Grease Multi-purpose grease „ Apply two strokes of lubricating grease from the grease gun per grease nipple. „ Remove excess lubricating grease at the grease nipple. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 98 Maintenance - Lubrication 15.2 Lubrication chart - Machine KMG000-023 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 99 Maintenance - Lubrication Lubrication chart - Machine 15.2 Every 50 operating hours Every 100 operating hours For the “accelerator roller” version EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 100: Storage
„ Touch up damaged paint and preserve all uncoated areas thoroughly with rust protection agent. „ Check all moving components for smooth running. If necessary remove, clean, grease and remount. „ If parts need to be replaced, use KRONE original spare parts only. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 101 Write down all repair jobs which must be performed by the next harvest and arrange for them to be done with sufficient lead time. Your KRONE dealer is better able to perform maintenance service and any required repairs outside of harvest season.
-
Page 102: Waste Disposal
Rubber • Rubber parts (hoses, tyres, …) must be brought to a rubber recycling centre. Electronic scrap • All electronic parts must be brought to a disposal point for electronic scrap. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 103: Appendix
Appendix Circuit diagram 18.1 Appendix 18.1 Circuit diagram >>> 2 150100881_08_en [} 104] EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... -
Page 115: Index
Connecting the machine to the tractor ....44 Consumables ..........20, 36 Contact ..............2 Contact data of your dealer ........2 Control and Display Elements ......37 Conversion table ..........9 Cross references ..........6 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en... - Page 116 Fold down the front guard ........50 Folding down side guard (working position) ..51 Folding up side guard (transport position) ..51 Folding up the front guard ........50 Front guard ............49 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 117 Move parking jacks into support position ... 52 Move parking jacks into transport position ..52 Moving cross conveyors ........70 Mowing ............... 55 Noise may damage your health......21 Notes with information and recommendations ..9 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 118 Target group of this document ......6 Technical data ............ 35 Technical limit values ......... 16 Technically sound state of the machine ..... 15 Term “machine” ............ 7 Tightening torques..........74 Top link pin ............41 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 119 Venting the friction clutch ........78 Von Transport- in Vorgewendestellung ....53 Von Vorgewende- in Transportstellung ....54 Vorgewendestellungen ........53 Warning signs............8 Warnings of property damage/environmental damage ..............9 Waste disposal ..........102 EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
- Page 120 This page has been left blank deliberately. EasyCut B 870 CV Collect Original Operating Instructions 150000707_01_en...
-
Page 121: Declaration Of Conformity
Machine: Mower Combination Type: EasyCut B 870 CV Collect to which this declaration refers is in compliance with the following relevant provisions: • EC Directive 2006/42/EC (Machinery) The undersigned Managing Director is authorised to compile the technical documents. - Page 122 Maschinenfabrik Bernard Krone GmbH & Co. KG * Heinrich-Krone-Straße 10 D-48480 Spelle * Postfach 11 63 D-48478 Spelle ' +49 (0) 59 77 / 935-0 6 +49 (0) 59 77 / 935-339 ü www.landmaschinen.krone.de...