Download Print this page
Dynojet PCV F Installation Instructions And Technical Information
Dynojet PCV F Installation Instructions And Technical Information

Dynojet PCV F Installation Instructions And Technical Information

2017-2019 yamaha t-max 530

Advertisement

Quick Links

FUEL AND IGNITION
2017-2019 Yamaha T-Max 530
I n s t a l l a t i o n I n s t r u c t i o n s
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
22-082
2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com
www.powercommander.com
PARTS LIST
1
Power Commander
1
USB Cable
1
Installation Guide
2
Power Commander Decals
2
Dynojet Decals
3
Velcro strips
1
Alcohol swab
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
THE LATEST POWER COMMANDER
SOFTWARE AND MAP FILES CAN BE
DOWNLOADED FROM OUR WEB SITE AT:
www.powercommander.com
2017-2019 Yamaha T-Max 530 - PCV F/I - 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the PCV F and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Dynojet PCV F

  • Page 1 SOFTWARE AND MAP FILES CAN BE DOWNLOADED FROM OUR WEB SITE AT: www.powercommander.com PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION 2191 Mendenhall Drive North Las Vegas, NV 89081 (800) 992-4993 www.powercommander.com 22-082 www.powercommander.com 2017-2019 Yamaha T-Max 530 - PCV F/I - 1...
  • Page 2: Usb Connection

    Center Software. Once gear position is setup INPUT 1 you can alter your map based on gear position and setup gear dependent kill times when using a quickshifter. Wire connections: Analog- This input is for a 0-5v signal such as To input wires into the PCV first remove the rubber engine temp, boost, etc. Once this input plug on the backside of the unit and loosen the is established you can alter your fuel curve screw for the corresponding input. Using a 22-24 based on this input in the control center gauge wire strip about 10mm from its end. Push the software. wire into the hole of the PCV until is stops and then tighten the screw. Make sure to reinstall the rubber Crank- Do NOT connect anything to this port unless plug. instructed to do so by Dynojet. It is used to transfer crank trigger data from one module to NOTE: If you tin the wires with solder it will make another. inserting them easier. 22-082 www.powercommander.com 2017-2019 Yamaha T-Max 530 - PCV F/I - 2...
  • Page 3 FIG.A Lift up the seat. Remove bodywork panels shown in Figure A. - Central tunnel cover ( 1 ) - Footboards ( 2 & 3) left and right side - Central tunnel side panels ( 4 ) left and right side - Fuel tank cover (5) FIG.B Remove bodywork panels shown in Figure B. - Central tunnel side panels (1) on left and right side - Side panels (2) on left and right side - Front fairing mid panels (3) on left and right side FIG.C Remove the plastic footboard support on the right side (Fig. C). 22-082 www.powercommander.com 2017-2019 Yamaha T-Max 530 - PCV F/I - 3...
  • Page 4 FIG.D Install the PCV module on the left side of the fuel tank (Fig. D). Use the supplied Velcro to secure the module. Clean surfaces with the alcohol swab before attaching. Secure the PCV ground wire to the engine using the engine side cover bolt shown in Figure D. Ground FIG.E Locate and unplug the stock Crank Position Sensor connectors on the left side of the scooter (Fig. E). Unplug This is a 2-pin connector pair located next to the belt cooling filter. FIG.F Route the pair of PCV connectors with BROWN colored wire to this area and plug the PCV wiring harness in-line of the stock Crank Position Sensor connectors (Fig. F). 22-082 www.powercommander.com 2017-2019 Yamaha T-Max 530 - PCV F/I - 4...
  • Page 5 FIG.G Unplug both Fuel Injectors located at the front of the fuel tank. 10 Route the PCV wiring harness to the Fuel Injectors. Plug the PCV wiring harness in-line of both Fuel Injectors (Fig. G). The pair of PCV connectors with ORANGE colored wires go to the LEFT injector. The pair of PCV connectors with YELLOW colored wires go to the RIGHT injector. FIG.H 11 Unplug the Throttle Position Sensor on the right side of the throttle bodies (Fig. H). 12 Plug the PCV wiring harness in-line of the Throttle Position Sensor. FIG.J 13 Route the PCV wiring harness branch with spade connectors towards the Ignition Coil located towards the forward left side of the scooter (Fig. J). 22-082 www.powercommander.com 2017-2019 Yamaha T-Max 530 - PCV F/I - 5...
  • Page 6 FIG.K 14 Unplug both of the stock wires at the Ignition Coil (Fig. K). 15 Plug the pair of PCV RED/WHITE wires in-line of the Ignition Coil and the stock RED/BLACK wire. 16 Plug the PCV GREEN and WHITE/GREEN wires in-line of the Ignition Coil and the stock ORANGE wire. 17 Reinstall all of the bodywork. 22-082 www.powercommander.com 2017-2019 Yamaha T-Max 530 - PCV F/I - 6...

This manual is also suitable for:

I 22082