Related Manuals for Danfoss Link Hydronic Controller
Summary of Contents for Danfoss Link Hydronic Controller
- Page 1 MaKing MoDeRn liVing PossiBle Installation Guide Danfoss Link™ Hydronic Controller Danfoss heating solutions...
-
Page 2: Table Of Contents
5.7 Leaving the service area in Danfoss Link™ CC ....... . -
Page 3: Quick Guide For Installation
2. Introduction Danfoss Link™ is a wireless control system for a variety of heating systems. The Danfoss Link™ HC is a part of this system allowing wireless control of manifolds for water based floor heating/cooling. 3. Functional Overview (fig. 2) Output LEDs. -
Page 4: Mounting And Installation Procedure (Sequential)
4. Mounting and Installation Procedure (Sequential) The wireless systems transmission range is sufficient for most applications; however, wire- less signals are weakened on the way from the Danfoss Link™ to the Room Thermostats and each building has different obstacles. Checklist for optimal installation and best wireless signal strength (fig. 1): • No metal objects between the Danfoss Link™... -
Page 5: Input For Heating And Cooling
Connect all actuators (TWA), before mains powering the unit! Then, connect the Danfoss Link™ HC power supply plug to a 230 V power supply, when all actuators, pump and boiler controls and other inputs are installed. The Danfoss Link™ HC is now ready to be added to the Danfoss Link™... -
Page 6: Configuring Danfoss Link™ Hc
Begin Registration ™ Click here for adding the Danfoss Link Note! During installation, the distance between the Danfoss Link™ CC and the Danfoss Link™ HC must not exceed 1.5m. Configuring Danfoss Link™ HC Note! Configuring Danfoss Link™ HC is made from the Danfoss Link™ CC. -
Page 7: Creating Rooms
Installation Guide Danfoss Link™ HC Creating rooms Danfoss recommends to create and add device(s) to one room in a single step, and there- after move on to the next room. Service Options Rooms and Devices Edit Room Name Add New Room... -
Page 8: Performing A Network Test After Adding New Devices
Danfoss Link™ CC guides through troubleshooting and gives useful tips for speeding up the process. Leaving the service area in Danfoss Link™ CC Press the SETUP pin for 3 seconds and put back the front cover to the Danfoss Link™ CC. 6. Maintenance Removing an output... -
Page 9: Factory Reset
Installation Guide Danfoss Link™ HC Factory reset • Disconnect the power supply for the Danfoss Link™ HC. • Wait for green LED to turn off. • Press and hold the Install/Link Test (fig. 2 ). • While holding Install/Link Test, reconnect the power supply. - Page 10 Installation Guide Danfoss Link™ HC Danfoss Heating Solutions VIFZL402 06/2013...
- Page 11 Installation Guide Danfoss Link™ HC Fig. 1 Danfoss Link™ RS Danfoss Link™ HC Metal Danfoss Link™ CC Danfoss Link™ RS Danfoss Link™ HC Danfoss Link™ RS Metal Danfoss Link™ CC Fig. 2 Fig. 3 06/2013 VIFZL402 Danfoss Heating Solutions...
- Page 12 Installation Guide Danfoss Link™ HC Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15 Fig. 16 Danfoss Heating Solutions VIFZL402 06/2013...
- Page 13 Danfoss A/S Indoor Climate Solutions ulvehavevej 61 7100 Vejle Denmark Phone: +45 7488 8500 fax: +45 7488 8501 email: heating.solutions@danfoss.com www.heating.danfoss.com VifZl402...