Clarke Strong-Arm CTJ1500QULP Operating & Maintenance Instructions
  1. Manuals
  2. Brands
  3. Clarke Manuals
  4. Jacks
  5. Strong-Arm CTJ1500QULP
  6. Operating & maintenance instructions

Clarke Strong-Arm CTJ1500QULP Operating & Maintenance Instructions

1.5 tonne garage jack
Hide thumbs Also See for Strong-Arm CTJ1500QULP:
Table of Contents

Advertisement

Quick Links

Download this manual
1.5 TONNE GARAGE JACK
Model No: CTJ1500QULP
PART NO: 7623075
OPERATING & MAINTENANCE
INSTRUCTIONS
GC01/13

Advertisement

Table of Contents
loading

Related Manuals for Clarke Strong-Arm CTJ1500QULP

Summary of Contents for Clarke Strong-Arm CTJ1500QULP

  • Page 1 1.5 TONNE GARAGE JACK Model No: CTJ1500QULP PART NO: 7623075 OPERATING & MAINTENANCE INSTRUCTIONS GC01/13...

  • Page 2: Specification

    Please note that details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...

  • Page 3: General Safety Precautions

    1. Check the jack for damage before use and do not use if damaged. If in doubt, DO NOT use. Consult your local dealer. 2. ALWAYS use spare parts supplied by Clarke International. Using non- standard parts could be extremely dangerous.

  • Page 4: Unpacking And Assembly

    UNPACKING AND ASSEMBLY 1. Remove the socket headed screw from the handle. 2. Insert the handle fully into the Handle Socket handle yoke until it engages with Headed the jack control valve at the base Screw of the yoke. 3. Re-fit the socket headed screw to Handle secure the handle to the jack.

  • Page 5: Troubleshooting

    NOTE: The jack may move slightly during operation. It is important therefore, that the floor is clean and free from debris. 6. Position axle stands directly beneath suitable supporting points on the vehicle, and very gently twist the control valve release knob anticlockwise.

  • Page 6: Maintenance

    • The oil should be almost level with the bottom of the oil filler hole. • Oil can be topped up using Clarke Hydraulic Oil (p/no 3050830 for 1 litre). 3. Purge any air from the system and replace the oil filler plug.

  • Page 7: Declaration Of Conformity

    DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 8 GENERAL COMPONENT PARTS t s i s i s c i l t i l t f i t f i When requesting replacement parts, please quote the prefix; HACTJ1500QLG, followed by the number listed above. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 9 GENERAL COMPONENT PARTS Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...
  • Page 10 HYDRAULIC COMPONENT PARTS When requesting replacement parts, please quote the prefix; HACTJ1500QLG, followed by the number listed above. Parts & Service: 020 8988 7400/E-mail:Parts@clarkeinternational.com or Service@clarkeinternational.com...

  • Page 11: Environmental Protection

    HYDRAULIC COMPONENT PARTS t s i n i l n i l n i l n i l n i l ENVIRONMENTAL PROTECTION One of the most damaging sources of environmental pollution is oil products. Never throw away used hydraulic oil with domestic refuse or flush it down a sink or drain.

Table of Contents