Page 2
Via Benini, 1 40069 - Zola Predosa BOLOGNA - ITALY Hereby declares that: the 959 B-E automation system • is intended to be incorporated into machinery, or to be assembled with other machinery to constitute machinery in compliance with the requirements of Directive 89/392 EEC, and subsequent amendments 91/368 EEC, 93/44 EEC and 93/68 EEC;...
Page 3
6) FAAC S.p.A. cannot be held responsible for any damage caused by improper use or different from the use for which the automation system is destined to.
Page 4
ITALIANO 2x0,5 mm Fig. 2a Fig. 2b Fig. 3 Fig. 8 Fig. 4...
Page 6
ITALIANO Tav. A: MONTAGGIO SULL’ARCHITRAVE (BRACCIO ARTICOLATO A SPINGERE) • Table A: LINTEL MOUNTING (PUSHING ARTICULATED ARM) Schéma A: MONTAGE SUR LE LINTEAU (BRAS ARTICULÉ À POUSSER)• Übersicht A: STURZEINBAU (DRÜCK-GELENKARM) Lám. A: MONTAJE EN EL DINTEL (BRAZO ARTICULADO DE EMPUJE) Piano di foratura •Drilling template •Schéma de perçage •Bohrbild •Plano de perforación Quote d'installazione •...
Page 7
ITALIANO Tav. B: MONTAGGIO SULLA PORTA (BRACCIO ARTICOLATO A SPINGERE) • Table B: DOOR MOUNTING (PUSHING ARTICULATED ARM) Schéma B: MONTAGE SUR LA PORTE (BRAS ARTICULÉ À POUSSER) • Übersicht B: TÜREINBAU (DRÜCK-GELENKARM) Lám. B: MONTAJE EN LA PUERTA (BRAZO ARTICULADO DE EMPUJE) Piano di foratura •Drilling template •Schéma de perçage •Bohrbild •Plano de perforación Quote d'installazione •...
Page 8
ITALIANO Tav. C: MONTAGGIO SULL’ARCHITRAVE (BRACCIO A PATTINO)• Table C: LINTEL MOUNTING (SLIDING ARM) • Schéma C: MONTAGE SUR LE LINTEAU (BRAS À PATIN) • Übersicht C: STURZEINBAU (GLEITARM) Lám. C: MONTAJE EN EL DINTEL (BRAZO CON PATÍN ) Piano di foratura •Drilling template •Schéma de perçage •Bohrbild •Plano de perforación Quote d'installazione •...
Page 9
ENGLISH FAAC 959 B-E Table 2: Technical specifications of 959MP Electronic Control The 959 B-E automatic unit for swing doors is a one-piece unit Unit + 959 B-E Programming unit consisting of an electromechanical device that allows door opening to be controlled by means of a driving arm.
Page 10
ENGLISH N.B.: 1) For installation of electrical cables use suitable rigid installation distances are given in Table A/B. or flexible piping. Slacken the fixing screw (6) and assemble the two arms by 2) Always keep the low voltage accessory connection means of coupling (3) (fig.
Page 11
(fig. 11 - ref. 4) for more than 4 seconds. This function enables the closed position force to be increased 5. 959 B-E PROGRAMMING UNIT by further loading the transmission system after the door has reached the mechanical closure end stop.
Page 12
(connection, microwave radar and/or passive infrared sensors. To maintenance). connect the FAAC sensors/radar units equipped with a 5- pole electrical cable, refer to fig. 18. 11. Emergency control (fig. 19/a): any control device (normally a pushbutton) which, by opening a contact, commands an emergency closure of the system.
EMERGENCY CLOSURE input (fig.19/ LEDS DI SEGNALAZIONE STATUS LEDS 8. “CODIS” EXTERNAL PROGRAMMING UNIT (OPTIONAL) The 959 B-E automation unit can also be controlled by an RESET external programming unit in place of the function selector and of the 959 B-E programming unit.
Page 15
ENGLISH Table 7: programming functions of the activation of the internal/ external control devices. FUNCT.NO. FUNCTIONS LEDS LED 6 The standard setting is 2 seconds. NIGHT PAUSE TIME: adjust to 0-30 LED 1 o OFF OFF OFF OFF OFF Output Level III seconds.
Page 16
(speed, pause times, etc.) must be performed by OFF ON OFF OFF OFF Governor and brake fault means of the internal 959 B-E programming unit. ON ON OFF OFF OFF Initialisation process not possible CODIS - permanent installation: the CODIS is installed Opening angle insufficient permanently;...
(LED lit steadily). See fig. 2. DESCRIPTION The 959 B-E automatic unit for swing doors is a one-piece unit consisting of an electromechanical device that allows door opening to be controlled by means of a driving arm. The door POSITION “1”: AUTOMATIC...
Page 18
Le descrizioni e le illustrazioni del presente manuale non sono impegnative. La FAAC si riserva il diritto, lasciando inalterate le caratteristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per qualsiasi altra esigenza di carattere costruttivo o commerciale.