Table of Contents
Related Manuals for tams elektronik WD-1
Summary of Contents for tams elektronik WD-1
- Page 1 WD-1 Weichendecoder Motorola-Format Points decoder Motorola format Décodeur d’aiguillage Format Motorola Anleitung Wisseldecoder Motorola-Format Manual Mode d´emploi Handleiding Art.-Nr. 21-01-028 / 22-01-028...
- Page 2 © 01/2007 Tams Elektronik GmbH Alle Rechte, insbesondere das Recht der Vervielfältigung und Verbreitung sowie Übersetzung vorbehalten. Vervielfältigungen und Reproduktionen jeglicher Form bedürfen schriftlichen Genehmigung durch die Tams Elektronik GmbH. Deutsch Technische Änderungen vorbehalten. © 01/2007 Tams Elektronik GmbH English All rights reserved.
-
Page 3: Table Of Contents
English WD-1 Table of contents How to use this manual Intended use Safety instructions EMC declaration Operation overview Technical specifications Checking the package contents Required tools and consumables Safe and correct soldering Assembling the kit Performing a visual check Connecting the points decoder... -
Page 4: How To Use This Manual
WD-1 English How to use this manual If you have no specialist technical training, this manual gives step-by- step instructions for safe and correct assembly of the kit and fitting of the ready-built module, and operation. Before you start, we advise you to read the whole manual, particularly the chapter on safety instructions and the FAQ chapter. - Page 5 English WD-1 Electrical hazards § Touching powered, live components, § touching conducting components which are live due to malfunction, § short circuits, § connecting the circuit to another voltage than specified, § impermissibly high humidity, § condensation build up can cause serious injury due to electrical shock. Take the following precautions to prevent this danger: §...
-
Page 6: Emc Declaration
WD-1 English Thermal danger A hot soldering iron or liquid solder accidentally touching your skin can cause skin burns. As a precaution: § use a heat-resistant mat during soldering, § always put the hot soldering iron in the soldering iron stand, §... -
Page 7: Operation Overview
English WD-1 § Connect the transformer only to an approved mains socket installed by an authorised electrician. § Make no changes to the original parts and accurately follow the instructions, circuit diagram and PCB layut included with this manual. §... -
Page 8: Checking The Package Contents
WD-1 English Checking the package contents Check the contents of the package for completeness after unpacking: § one kit, containing the components listed in the parts list (see page I) and one PCB or one ready-built module, § one manaul. -
Page 9: Assembling The Kit
English WD-1 § Solder quickly: holding the iron on the joints longer than necessary can destroy components and can damage copper tracks or soldering eyes. § Observe correct polarity orientation of semi-conductors, LEDs electrolytic capacitors and integrated circuits before soldering and ensure that the solder time does not exceed 5 seconds, otherwise components can be damaged. - Page 10 WD-1 English Resistors Resistors reduce current. Their mounting orientation is of no importance. The value of resistors for smaller power ratings (under 5 W) is indicated through colour rings. Every colour stands for another figure. The colour ring in brackets indicates the tolerance of the resistor which here is of no importance.
- Page 11 English WD-1 voltage sustaining capability higher than required is always possible. Diodes Diodes allow the current to pass through in one direction only (forward direction), simultaneously the voltage is reduced by 0,3 to 0,8 V. Exceeding of the limit voltage always will destroy the diode, and allow current to flow in the reverse direction.
- Page 12 WD-1 English Integrated circuits (ICs) Depending on the type, ICs fulfil various tasks. They are polarized and therefore have to be mounted in a certain direction. The most common housing form is the so-called "DIL"-housing, from which 4, 6, 8, 14, 16, 18 or more "legs"...
-
Page 13: Performing A Visual Check
English WD-1 Caution: Diodes, ICs, electrolytic capacitors and transistors must be placed in the right direction! If you solder them the wrong way the affected parts can be damaged when you connect the power. In the worst case the whole circuit can be damaged. -
Page 14: Connecting The Points Decoder
WD-1 English Connecting the points decoder Caution: Switch off the central unit before connecting the points decoder! There are terminal strips soldered to the in- and outputs. Insert the connecting cables into the relevant terminals and fasten the screws. The connections diagram (figure 3) shows the correct assembly. -
Page 15: Manufacturer's Note
English WD-1 § The points decoder does not work. Possible cause: The connection of the decoder to the points or to the central unit is interrupted. à Check the connections. Possible cause: The wires from the central unit to the points decoder are incorrectly connected. - Page 16 WD-1 English of the parts according to the parameters in not mounted state as well as the adherence to the technical specifications of the circuit when assembled and connected according to the manual. Other claims are excluded. By law, we are not responsible for damages or secondary damages in connection with this product.
- Page 17 WD-1 Einstellung der Adresse / Adjusting the address Réglage de l’adresse / Instellen van het adres Beispiel: Einstellung der Adresse "1" Example: Adjusting the address "1" Exemple: Réglage de l´adresse "1" Voorbeeld: Instellen van adres "1" Adresse Weiche JP10 Address...
- Page 18 WD-1 Adresse Weiche JP10 Address Points Adresse Aiguillage Adres Wissel 73 – 76 2 – 3 1 – 2 1 – 2 77 – 80 1 – 2 1 – 2 81 – 84 1 – 2 2 – 3 1 –...
- Page 19 WD-1 Adresse Weiche JP10 Address Points Adresse Aiguillage Adres Wissel 197 – 200 2 – 3 2 – 3 201 – 204 1 – 2 2 – 3 205 – 208 2 – 3 2 – 3 209 – 212 2 –...
- Page 20 WD-1 Stückliste - Parts list Nomenclature - Stuklijst Widerstände 1,5 kΩ Resistors 220 kΩ Résistances 22 kΩ Weerstanden 100 kΩ 47 kΩ 330 kΩ R7, R8 4,7 kΩ Kondensatoren - Condensers 100 nF Condensateurs - Condensatoren 1,8 nF 3,9 nF 100 µF...
- Page 21 WD-1 Kurzschlußstecker 5 Stück Short circuit terminators Jumpers – Kortsluitstekkers oder ähnlich - or similar - ou équivalent - of gelijkwaardig Bestückungsplan - PCB layout Plan d´implantation - Printplan Fig. 1 Seite - Page - Page - Pagina I.2...
- Page 22 WD-1 WD-1 Fig. 2: Schaltplan - Circuit diagram - Schéma de principe - Schakelschema Seite - Page - Page - Pagina II Seite - Page - Page - Pagina II...
- Page 23 WD-1 WD-1 Fig. 3: Anschlußplan – Connections – Plan de raccordement – Aansluit plan Fig. 3a: Fig. 3b: Anschluß an separate Stromversorgung. Anschluß direkt an Digitalspannung. Connection to a seperate transformer. Connection directly to digital voltage. Connexion à une alimentation séparée.
- Page 24 Actuele informatie en tips: http://www.tams-online.de Garantie und Service: Warranty and service: Garantie et service: Garantie en service: Tams Elektronik GmbH Rupsteinstraße 10 D-30625 Hannover fon: +49 (0)511 / 55 60 60 fax: +49 (0)511 / 55 61 61 e-mail: modellbahn@tams-online.de...