Advertisement
Quick Links
π
H-3934, H-3935
ELECTRIC LIFT TABLE
SPECIFICATIONS
Weight Capacity
Min. Table Height
Max. Table Height
Travel
Platform Width
Platform Length
Base Frame Width
Base Frame Length
Weight
Sound Pressure Level
Operating Environment
WARNING! Do not operate this lift table unless
you have been trained to use it, authorized
to do so and have checked that it is in good
condition. The operator should read all of the
warning signs and instructions here and on the
lift table before using it.
1.
DO NOT concentrate the load at one point on the
platform or pallet. ALWAYS uniformly distribute each
layer of load over the supporting surface.
2. DO NOT use the lift for any purpose other than its
intended use.
3. DO NOT install the lift table on an unlevel or soft
surface. The lift base frame must be supported
along its entire length and width. Failure to
completely support the base frame could result in
damage to the lift.
4. DO NOT use the lift table with an unstable,
unbalanced or loosely stacked load. Unbalanced
loads may become unstable and fall. SEVERE
PERSONAL INJURY and PROPERTY DAMAGE may result.
PAGE 1 OF 7
1-800-295-5510
uline.com
TECHNICAL INFORMATION
H-3934
H-3935
2,000 lbs.
2,000 lbs.
8⁄"
8⁄"
38⁄"
38⁄"
30"
30"
28"
36"
48"
48"
24⁄"
24⁄"
49"
49"
402 lbs.
416 lbs.
<70dB(a)
<70dB(a)
Indoors
Indoors
SAFETY GUIDELINES
5. DO NOT overload the lift table. ALWAYS stay within
6. SHEARING HAZARD. ALWAYS keep hands and feet
7.
8. PINCH POINT HAZARD. ALWAYS keep feet, hands and
9. DO NOT change the relief valve setting. The relief
Platform Length
Base Length
the designated capacity ratings. SEVERE PERSONAL
INJURY and PROPERTY DAMAGE could result.
clear of the scissor mechanism and all moving
components. DO NOT put hands or fingers under
the platform when in use. SEVERE PERSONAL INJURY
could result.
CRUSHING HAZARD. ALWAYS keep hands and feet
clear of all moving components. DO NOT put feet
on the base frame when in use. SEVERE PERSONAL
INJURY could result.
fingers away from the underside of the platform and
all moving components. SEVERE PERSONAL INJURY
could result.
valve is installed to protect the operator and the
lift table. Changing the relief valve setting may
compromise the performance and safety of the lift.
SEVERE PERSONAL INJURY and PROPERTY DAMAGE
could result.
Platform
Width
Base
Width
Travel
Raised
Height
Lowered
Height
0413 IH-3934
Advertisement
Related Manuals for U-Line H-3934
Summary of Contents for U-Line H-3934
- Page 1 π H-3934, H-3935 1-800-295-5510 uline.com ELECTRIC LIFT TABLE TECHNICAL INFORMATION SPECIFICATIONS H-3934 H-3935 Weight Capacity 2,000 lbs. 2,000 lbs. Platform Width Base Min. Table Height 8⁄" 8⁄" Width Max. Table Height 38⁄" 38⁄" Travel 30" 30" Platform Length Platform Width 28"...
-
Page 2: Recommended Floor Area
SAFETY GUIDELINES CONTINUED RECOMMENDED FLOOR AREA 10. NEVER leave the loaded lift table unattended unless the platform is in the fully lowered position. The lift table’s recommended floor area is a distance of 11. ALL lift servicing must be performed by qualified 39 inches (1 meter) from the unit on all sides. - Page 3 INSTALLATION INSTRUCTIONS CONTINUED Base Frame Anchor Holes – 4 pre-drilled base frame Figure 2 anchor holes are provided inside the base frame to secure the lift to the floor or installation surface. Tools Required • Banding or Strap Cutters • Drill with 1/2" concrete drill • 3/4"...
- Page 4 INSTALLATION INSTRUCTIONS CONTINUED 9. Rotate the maintenance bars to their stored position 10. The lift is now ready for operation. Refer to the and run the lift up and down several times to following section for complete operating instructions. remove any air that may have been trapped in the hydraulic system due to shipping.
-
Page 5: Maintenance
MAINTENANCE DISENGAGE THE MAINTENANCE BARS The lift table is designed to provide years of trouble-free service and requires very little maintenance. However, Depress the UP button to raise the platform to its a routine inspection and maintenance program will fully raised position. When the lift is fully raised, prevent costly replacement of parts and/or downtime. - Page 6 MAINTENANCE CONTINUED MONTHLY INSPECTION AND 9. Finally, raise the lift and disengage the maintenance bars by returning them to their stored MAINTENANCE position. If the lift is equipped with an accordion bellows skirt, lift the bottom of the bellows skirt and secure in the CHANGING THE AW32 HYDRAULIC OIL raised maintenance position with the maintenance ties.
-
Page 7: Troubleshooting
MAINTENANCE CONTINUED CHANGING THE AW32 HYDRAULIC OIL 8. Raise the lift to its maximum height and disengage the maintenance bars. Completely raise and lower CONTINUED the lift 3 times to remove any trapped air from the hydraulic system. Fill the reservoir with the new hydraulic fluid and run the motor by pressing the UP button to prime the 9.