Aaeon FSB-866G Manual
  1. Manuals
  2. Brands
  3. Aaeon Manuals
  4. Computer Hardware
  5. FSB-866G
  6. Manual

Aaeon FSB-866G Manual

Full-size cpu card, intel pentium 4/celeron-d picmg, full-size cpu card with ddr, ethernet, compactflash
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
F u l l - s i z e C P U C a r d
F S B - 8 6 6 G
FSB-866G
®
®
®
Intel
Pentium
4/Celeron
-D
PICMG, Full-size CPU Card
With DDR, Ethernet,
™
CompactFlash
FSB-866G Rev. A Manual 1st Ed.
Aug. 2005

Advertisement

Table of Contents
loading

Related Manuals for Aaeon FSB-866G

Summary of Contents for Aaeon FSB-866G

  • Page 1 F u l l - s i z e C P U C a r d F S B - 8 6 6 G FSB-866G ® ® ® Intel Pentium 4/Celeron PICMG, Full-size CPU Card With DDR, Ethernet, ™ CompactFlash FSB-866G Rev. A Manual 1st Ed. Aug. 2005...

  • Page 2: Copyright Notice

    AAEON assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein. AAEON reserves the right to make changes in the product design without notice to its users.
  • Page 3 F u l l - s i z e C P U C a r d F S B - 8 6 6 G Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. ™...

  • Page 4: Packing List

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • FSB-866G CPU Card • Floppy Cable • ATA-100 Cable •...

  • Page 5: Table Of Contents

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G Contents Chapter 1 General Information 1.1 Introduction..............1-2 1.2 Feature ..............1-4 1.3 Specification .............. 1-5 Chapter 2 Quick Installation Guide 2.1 Safety Precautions ............
  • Page 6 F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.18 AC97 Connector (CN6) ........... 2-12 2.19 PS/2 Keyboard & Mouse Connector (CN7) .... 2-13 2.20 Internal Keyboard Connector (CN8)......2-13 2.21 PCI Express Connector (CN9) ......

  • Page 7: Chapter 1 General Information

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G Chapter General Information 1- 1 Chapter 1 General Information...

  • Page 8: Introduction

    533 to 800MHz. Moreover, this model supports dual channel DDR memory (DDR333/400) providing a maximum capacity up to 2GB. The VGA controller of FSB-866G is an integrated GMA900 2D/3D Graphics Accelerator inside the Intel 915GV chipset which enhances VGA performance capability, with a core frequency up to 333MHz.
  • Page 9 F u l l - s i z e C P U C a r d F S B - 8 6 6 G The AAEON FSB-866G full-size CPU card is designed to fulfill the requirements of tough applications that demand high speed and stable computing performance.

  • Page 10: Feature

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 1.2 Features • ® ® ® Support Intel Pentium 4 / Celeron -D CPU up to 3.8GHz •...

  • Page 11: Specification

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 1.3 Specification System ® CPU: Support Intel LGA 755 ® ® Pentium 4 and Celeron Processors up to 3.8 GHz (533/800MHz FSB) ®...
  • Page 12 F u l l - s i z e C P U C a r d F S B - 8 6 6 G Expansion Interface: ISA/ PCI/ PCI Express Connector (DF13-30P) Battery: Lithium battery Power Supply Voltage: +12V ATX, other supply from Backplane VGA Controller: Integrated GMA 900 on...
  • Page 13 F u l l - s i z e C P U C a r d F S B - 8 6 6 G FDD Interface: Standard FDD port x 1 (supports up to 1 floppy device) Serial Ports: Two COM ports: (Internal pin header, external D-sub COM 1: RS-232 COM 2: RS-232/422/485...
  • Page 14 F u l l - s i z e C P U C a r d F S B - 8 6 6 G Chapter Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters further installation...

  • Page 15: Safety Precautions

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it.

  • Page 16: Location Of Connectors And Jumpers

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.2 Location of Connectors and Jumpers Component Side 2 - 3 Chapter 2 Quick Installation Guide...

  • Page 17: Mechanical Drawing

    F u l l - s i z e C P U C a r d F u l l - s i z e C P U C a r d F S B - 8 6 6 G F S B - 8 6 6 G 2.3 Mechanical Drawing 2.3 Mechanical Drawing...

  • Page 18: List Of Jumpers

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.

  • Page 19: List Of Connectors

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.
  • Page 20 F u l l - s i z e C P U C a r d F S B - 8 6 6 G FAN1 Fan Connector ATX Power Control Connector AC97 Connector PS2 Keyboard/Mouse Connector Internal Keyboard Connector LAN 1 Active LED Connector LAN 2 Active LED Connector PCI Express x1 Connector 2 - 7...

  • Page 21: Setting Jumpers

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.

  • Page 22: Clear Cmos (Jp1)

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.7 Clear CMOS (JP1) Function Close Clear Open Protected (default) 2.8 Front Panel Connector (FP1) Signal Signal Power On Button(+) Reset Switch(+)

  • Page 23: Rs232 Serial Port Connector (Com1)

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.10 RS232 Serial Port Connector (COM1) Signal Signal N.C. 2.11 RS232/422/485 Serial Port Connector (COM2) Signal Signal DCD(422TXD-/485DATA-) RXD(422RXD+)

  • Page 24: Lpt Port Connector (Lpt1)

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.13 LPT Port Connector (LPT1) Signal Signal #STROBE #AFD DATA0 #ERROR DATA1 #INIT DATA2 #SLIN DATA3 DATA4 DATA5 DATA6...

  • Page 25: Fan Connector (Fan1)

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.15 Fan Connector (FAN1) Signal +12V Speed Sense FAN Out Control 2.16 ATX Power Control Connector (CN1) Signal PS-ON +5VSB...

  • Page 26: Ps/2 Keyboard/Mouse Connector (Cn7)

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G 2.19 PS/2 Keyboard/Mouse Connector (CN7) Signal KB_DATA MS-DATA KB_CLK MS_CLK 2.20 Internal Keyboard Connector (CN8) Signal KB_CLK KB_DATA 2.21 PCI Express Connector (CN9)
  • Page 27 F u l l - s i z e C P U C a r d F S B - 8 6 6 G PCIe_TX2 PCIe_TX1 PCIe_TX2# PCIe_TX1# +12V PCIe-CLK2 +12V PCIe-CLK2# SMBDATA SMBCLK PCIe-RX2 +3.3V PCIe-RX2# +3.3V 2 - 14 Chapter 2 Quick Installation Guide...

  • Page 28: Chapter 3 Cpu, Heatsink And Fan Installation

    F u l l - s i z e C P U c a r d F S B - 8 6 6 G Chapter CPU, Heatsink and Fan Installation Chapter 3 CPU, Heatsink and Fan Installation...

  • Page 29: Cpu Installation And Motherboard Handling

    F u l l - s i z e C P U c a r d F S B - 8 6 6 G 3.1 CPU installation and motherboard handling Note: When integrating a Pentium 4 processor-based system, be sure to take the proper electrostatic discharge (ESD) precautions.
  • Page 30 F u l l - s i z e C P U c a r d F S B - 8 6 6 G b. Rotate Load Plate to fully open position c. Remove the Protective Cover Caution: Do not touch the Socket Contacts. This may result in damage to the contacts.
  • Page 31 F u l l - s i z e C P U c a r d F S B - 8 6 6 G Step 2: (Processor Handling) Note: Handle Processor by substrate edges only. Caution: Do not touch processor contacts at any time a.
  • Page 32 F u l l - s i z e C P U c a r d F S B - 8 6 6 G Step 3: (Positioning the CPU into socket) a. Grasp the processor with your thumb and forefinger on the edges with the orientation notches. The socket has cut-outs for your fingers when handled in this orientation.
  • Page 33 F u l l - s i z e C P U c a r d F S B - 8 6 6 G d. Close the upper plate (A), place the load lever back to the original position and tightly wedge the lever into the fastening tab.
  • Page 34 F u l l - s i z e C P U c a r d F S B - 8 6 6 G b. Viewing the board again from the topside make sure the bracket on the solder side has not shifted from its position.
  • Page 35 F u l l - s i z e C P U c a r d F S B - 8 6 6 G d. Fasten the four screws. First fasten the two screws (yellow) and then fasten the two screws (red) in sequence to secure the heatsink in place.

  • Page 36: Chapter 4 Award Bios Setup

    F u l l - s i z e C P U c a r d F S B - 8 6 6 G Chapter Award BIOS Setup Chapter 4 Award BIOS Setup...

  • Page 37: System Test And Initialization

    3. The CMOS memory has lost power and the configuration information has been erased. The FSB-866G CMOS memory has an integral lithium battery backup for data retention. However, you will need to replace the complete unit when it finally runs down.
  • Page 38 F u l l - s i z e C P U c a r d F S B - 8 6 6 G 4.2 Award BIOS Setup Awards BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off.
  • Page 39 F u l l - s i z e C P U c a r d F S B - 8 6 6 G PnP/PCI Configurations This entry appears if your system supports PnP/PCI. PC Health Status This menu allows you to set the shutdown temperature for your system.
  • Page 40 F u l l - s i z e C P U c a r d F S B - 8 6 6 G Abandon all CMOS value changes and exit setup. You can refer to the "AAEON BIOS Item Description.pdf" file in the CD for the meaning of each setting in this chapter.

  • Page 41: Chapter 5 Driver Installation

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G Chapter Driver Installation Chapter 5 Driver Installation...
  • Page 42 F u l l - s i z e C P U C a r d F S B - 8 6 6 G The FSB-866G comes with a CD-ROM that contains all drivers your need. In addition, you can activate the installation items through Autorun program which will install each driver directly.
  • Page 43 F u l l - s i z e C P U C a r d F S B - 8 6 6 G 5.1 Installation: Insert the FSB-866G CD-ROM into the CD-ROM Drive. And install the drivers from Step 1 to Step 4 in order. Step 1 – Install INF Driver 1.
  • Page 44 5. The system will help you install the driver automatically. 6. Please re-start your computer. Optional 1 –Install W83627EHF AP For FSB-866G Driver 1. Click on the W83627EHG AP For FSB-866G folder. 2. Double click on the Setup. 3. Follow the instructions that the window shows.

  • Page 45: Appendix A I/O Information

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G Appendix I/O Information Appendix A I/O Information...

  • Page 46: I/O Address Map

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G A.1 I/O Address Map Appendix A I/O Informaion...

  • Page 47: St Mb Memory Address Map

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G A.2 1 MB Memory Address Map Appendix A I/O Informaion...

  • Page 48: Irq Mapping Chart

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G A.3 IRQ Mapping Chart Appendix A I/O Informaion...

  • Page 49: Dma Channel Assignments

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G A.4 DMA Channel Assignments Appendix A I/O Informaion...

  • Page 50: Appendix B Programming The Watchdog Timer

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G Appendix Programming the Watchdog Timer Appendix B Programming the Watchdog Timer...

  • Page 51: Programming

    FSB-866G Uutilizes W83627EHG chipset as its watchdog timer controller. Below are the procedures to complete its configuration and the AAEON intial watchdog timer program is also attached based on which you can develop customized program to fit your application. Configuring Sequence Description...
  • Page 52 F u l l - s i z e C P U C a r d F S B - 8 6 6 G (2) Modify the data of configuration registers (3) Exit the W83627EHG config Mode. Undesired result may occur if the config Mode is not exited normally.
  • Page 53 F u l l - s i z e C P U C a r d F S B - 8 6 6 G = 01 Power LED pin is drived low. = 10 Power LED pin is a 1Hz toggle pulse with 50 duty cycle.
  • Page 54 F u l l - s i z e C P U C a r d F S B - 8 6 6 G second/minutes WatchDog Timer Register III (Index=F7h, Default=00h) Bit 7 : Mouse interrupt reset Enable or Disable Watchdog Timer is reset upon a Mouse interrupt Watchdog Timer is not affected by...

  • Page 55: W83627Ehg Watchdog Timer Initial Program

    F u l l - s i z e C P U C a r d F S B - 8 6 6 G B.2 W83627EHG Watchdog Timer Initial Program Example: Setting 10 sec. as Watchdog timeout interval ;/////////////////////////////////////////////////////////////////////////////////////////////// Mov dx,2eh ;Enter W83627EHG config mode Mov al,87h (out 87h to 2eh twice)
  • Page 56 F u l l - s i z e C P U C a r d F S B - 8 6 6 G ;/////////////////////////////////////////////////////////////////////////////////////////////// Dec dx Mov al,0f5h ;CRF5 (PLED mode register) Out dx,al Inc dx In al,dx And al,not 08h ;Set second as counting unit Out dx,al ;///////////////////////////////////////////////////////////////////////////////////////////////...

Table of Contents