1. Manuals
  2. Brands
  3. Aaeon Manuals
  4. Computer Hardware
  5. HSB-440I
  6. Manual

Aaeon HSB-440I Manual

Half-size cpu card
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HSB-440I
Half Size CPU Card
STPC Atlas SoC 133MHz
With LCD, Ethernet,
Two
USB Ports
HSB-440I Rev. A Manual
July 2003

Advertisement

Table of Contents
loading

Related Manuals for Aaeon HSB-440I

Summary of Contents for Aaeon HSB-440I

  • Page 1 HSB-440I Half Size CPU Card STPC Atlas SoC 133MHz With LCD, Ethernet, USB Ports HSB-440I Rev. A Manual July 2003...
  • Page 2 While reasonable efforts have been made in the preparation of this document to assure its accuracy, AAEON assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein.
  • Page 3 H a l f - s i z e C P U C a r d H S B - 4 4 0 I Acknowledgments All other products’ name or trademarks are properties of their respective owners. Award is a trademark of Award Software International, Inc. CompactFlash™...
  • Page 4 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: • 1 HSB-440I Half-size CPU Card • 1 Quick Installation Guide • 1 CD-ROM for manual (in PDF format), BIOS, and drivers •...

  • Page 5: Table Of Contents

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I Contents Chapter 1 General Information 1.1 Introduction ..................1-2 1.2 Features .................... 1-3 1.3 Specifications................... 1-4 Chapter 2 Quick Installation Guide 2.1 Safety Precautions ................
  • Page 6 H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.18 Digital I/O Connector (CN7)............ 2-14 2.19 USB Connector (CN8) ..............2-14 2.20 COM2 RS-232/422/485 Serial Port......... 2-15 2.21 Internal Mouse Connector (CN10)...........
  • Page 7 H a l f - s i z e C P U C a r d H S B - 4 4 0 I 3.13 Set Supervisor/User password........... 3-11 3.14 Save & Exit setup................. 3-12 3.15 Exit without saving ..............3-12 Appendix A Programming the WatchDog Timer Programming the watchdog timer ............A-2...

  • Page 8: Chapter 1 General Information

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I Chapter General Information 1- 1 Chapter 1 General Information...

  • Page 9: Introduction

    H S B - 4 4 0 I 1.1 Introduction HSB-440I is AAEON’ s half-size ISA bus CPU card with STPC Atlas low power consumption single chip solution. This single chip integrated many kinds of functions like: processor, graphic controller (with LCD interface), PCI bridge, and simple super I/O.

  • Page 10: Features

    • Watchdog & Digital I/O Note: TFT resolution only supports 640 x 480 and 800 x 600 (default). If you want to change the resolution, please visit AAEON’ s website (www.aaeon.com.tw) and download the BIOS. Chapter 1 General Information 1 - 3...

  • Page 11: Specifications

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 1.3 Specifications System CPU: STPC Atlas SoC 133MHz I/O Chipset: STPC Atlas + Winbond 83977F System Memory: Onboard 64MB memory VGA/LCD Controller STPC Atlas, Share up to 4MB, LCD...
  • Page 12 H a l f - s i z e C P U C a r d H S B - 4 4 0 I Parallel Port Supports SPP/EPP/ECP mode K/B and Mouse One Mini-DIN PS/2 keyboard and Mouse connector One internal keyboard pin header One internal mouse pin header Universal Serial Bus Two USB Port (One 5x2 pin header)
  • Page 13 H a l f - s i z e C P U C a r d H S B - 4 4 0 I Chapter Quick Installation Guide Notice: The Quick Installation Guide is derived from Chapter 2 of user manual. For other chapters and further installation instructions, please refer to the user manual CD-ROM that came with the product.

  • Page 14: Safety Precautions

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components.

  • Page 15: Location Of Connectors And Jumpers

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.2 Location of Connectors and Jumpers Locating connectors and jumpers (component side) Chapter 2 Quick Installation Guide 2 - 3...
  • Page 16 H a l f - s i z e C P U C a r d H S B - 4 4 0 I Locating connector (solder side) Chapter 2 Quick Installation Guide 2 - 4...

  • Page 17: Mechanical Drawing

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.3 Mechanical Drawing Mechanical drawing (component side) 2 - 5 Chapter 2 Quick Installation Guide...
  • Page 18 H a l f - s i z e C P U C a r d H S B - 4 4 0 I Mechanical Drawing (solder side) Chapter 2 Quick Installation Guide 2 - 6...

  • Page 19: List Of Jumpers

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.4 List of Jumpers The board has a number of jumpers that allow you to configure your system to suit your application.

  • Page 20: List Of Connectors

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.5 List of Connectors The board has a number of connectors that allow you to configure your system to suit your application.

  • Page 21: Setting Jumpers

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.6 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.

  • Page 22: Lcd Voltage Selection (Jp1)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.7 LCD Voltage Selection (JP1) Function +3.3V (Default) 2.8 TTL-LCD Clock Selection (JP2) Function Reverse Clock Clock (Default) 2.9 Onboard COM Port On/Off Selection (JP3) Function...

  • Page 23: Clear Cmos (Jp4)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.10 Clear CMOS (JP4) Warning: To avoid damaging the computer, always turn off the power supply before setting “...

  • Page 24: Front Panel Connector (Cn1)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.13 Front Panel Connector (CN1) Signal Signal IDE LED(-) IDE LED(+) External Buzzer(-) External Buzzer(+) Power LED(-) Power LED(+) Reset Switch(-) Reset Switch(+)

  • Page 25: Ttl Lcd Connector (Cn3)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.15 TTL_LCD Connector (CN3) Signal Signal +12V +12V LCD VCC (by JP1) LCD VCC (by JP1) N.C.

  • Page 26: At Power Connector (Cn4)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.16 AT Power Connector (CN4) Signal +12V -12V 2.17 COM3/COM4 RS-232 Serial Port Connector (CN5&CN6) Signal Signal Chapter 2 Quick Installation Guide 2 - 14...

  • Page 27: Digital I/O Connector (Cn7)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.18 Digital I/O Connector (CN7) Signal Signal GPIO 0 GPIO 8 GPIO 1 GPIO 9 GPIO 2 GPIO 10 GPIO 3 GPIO 11...

  • Page 28: Com2 Rs-232/422/485 Serial Port

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.20 COM2 RS-232/422/485 Serial Port Connector (CN9) Signal Signal DCD(422TXD-/485DATA-) RXD(422RXD+) TXD(422TXD+/485DATA+) DTR(422RXD-) 2.21 Internal Mouse Connector (CN10) Signal MS_CLK MS_DATA...

  • Page 29: Irda Connector(Cn12)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.23 IrDA Connector(CN12) Signal IRRX IRTX 2.24 PS2 Keyboard/Mouse Connector (CN13) Signal KB_DATA MS-DATA KB_CLK MS_CLK Chapter 2 Quick Installation Guide 2 - 17...

  • Page 30: Power Connector(Cn14)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.25 4P Power Connector (CN14) Signal +12V 2.26 3P Power Connector (CN15) Signal -12V 2.27 Floppy Connector (FDD1) Signal Signal #REDWC...

  • Page 31: Eide Connector (Hdd1)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I #DIR #STEP #WRITE DATA #WRITE GATE #TRACK0 #WRITE PROTECT #READ DATA #SIDE1 #DISK CHANGE 2.28 EIDE Connector (HDD1) Signal Signal IDE RESET...

  • Page 32: Vga Display Connector (Vga1)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I ADDR1 N.C. ADDR0 ADDR2 CS#1 CS#3 2.29 VGA Display Connector (VGA1) Signal Signal GREEN BLUE DDCDAT HSYNC VSYNC DDCCLK...

  • Page 33: Com1 Rs-232 Serial Port Connector (Com1)

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 2.30 COM1 RS-232 Serial Port Connector (COM1) COM1 is a D-SUB connector. The table below shows its pin assignments.

  • Page 34: Chapter 3 Award Bios Setup

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I Chapter Award BIOS Setup Chapter 3 Award BIOS Setup...
  • Page 35 The CMOS memory has lost power and the configuration information has been erased. The HSB-440I CMOS memory has an integral lithium battery backup for data retention. However, you will need to replace the complete unit when it finally runs down.

  • Page 36: Standard Cmos Feture

    Please notice that TFT resolution only supports 640 x 480 and 800 x 600 (default). If you want to change the resolution, please visit AAEON’ s website (www.aaeon.com.tw) and download the BIOS. Entering setup Power on the computer and press <Del>...
  • Page 37 H a l f - s i z e C P U C a r d H S B - 4 4 0 I Use this menu to change the values in the chipset registers and optimize your system performance. Integrated Peripherals Use this menu to specify your settings for integrated peripherals.
  • Page 38 This standard Setup Menu allows users to configure system components such as date, time, hard disk drive, floppy drive and display. Once a field is highlighted, on-line help information is displayed in the right box of the Menu screen. HSB-440I Chapter3 Award BIOS Setup 3 - 5...

  • Page 39: Advanced Bios Features

    3.4 Advanced BIOS Features By choosing the Advanced BIOS Features option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values for the HSB-440I. Chapter3 Award BIOS Setup 3 - 6...

  • Page 40: Advanced Chipset Features

    3.5 Advanced Chipset Features By choosing the Advanced Chipset Features option from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values for the HSB-440I. Chapter3 Award BIOS Setup 3 - 7...

  • Page 41: Integrated Peripherals

    H S B - 4 4 0 I 3.6 Integrated Peripherals By choosing the Integrated Peripherals from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values for the HSB-440I. Chapter3 Award BIOS Setup 3 - 8...

  • Page 42: Power Management Setup

    3.7 Power management setup By choosing the Power Management Setup from the INITIAL SETUP SCREEN menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values for the HSB-440I. Chapter3 Award BIOS Setup 3 - 9...

  • Page 43: Pnp/Pci Configuration

    H S B - 4 4 0 I 3.8 PnP/PCI configuration By choosing the PnP/PCI configurations from the Initial Setup Screen menu, the screen below is displayed. This sample screen contains the manufacturer’ s default values for the HSB-440I. Chapter3 Award BIOS Setup 3 - 10...

  • Page 44: Load Fail-Safe Defaults

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 3.11 Load Fail-Safe Defaults When you press <Enter> on this item you get a confirmation dialog box with a message similar to: Load Fail-Safe Default (Y/N)? Pressing "Y"...

  • Page 45: Save & Exit Setup

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I 3.14 Save & Exit setup If you select this option and press <Enter>, the values entered in the setup utilities will be saved in the chipset’...

  • Page 46: Appendix A Programming The Watchdog Timer

    H a l f - s i z e C P U C a r d H S B - 4 4 0 I Appendix Programming the Watchdog Timer Appendix A Programming the Watchdog Timer...
  • Page 47 H a l f - s i z e C P U C a r d H S B - 4 4 0 I Programming the watchdog timer The HSB-440I contains a watchdog timer reset pin (GP16). All reference material can ge gound below. ======================================== ** Title: WatchDog Timer Setup Utility (for W83977 GP16) ** Company: AAEON Technology Inc.
  • Page 48 H a l f - s i z e C P U C a r d H S B - 4 4 0 I unsigned char ReadAData(short int reg) outportb(IO_INDEX_PORT, reg); return (inportb(IO_DATA_PORT)); void WriteAData(unsigned char reg, unsigned char data) outportb(IO_INDEX_PORT, reg);...
  • Page 49 H a l f - s i z e C P U C a r d H S B - 4 4 0 I //caution:skip this step will be a mistake!! if (watch_dog_output_GP==12) //Set Register E2 to define GP12 WriteAData(0xE2, 0x0A); else if(watch_dog_output_GP==13) //Set Register E3 to define GP13 WriteAData(0xE3, 0x0A);...
  • Page 50 *ptr; printf("WinBond 83977 WatchDog Timer Setup Utility Version 1.0 \n"); printf("Copyright (c) 2000 AAEON Technology Inc. \n"); printf("This version only for W83977 that using GP%d to Reset System.\n",watch_dog_output_GP); if (argc == 1) printf("\n Syntax: WATCHDOG [time] \n");...

Table of Contents