XIEGU X5105 Instruction Manual
Hf+50mhz portable hf transceiver
Hide thumbs
Also See for X5105:
- Operation manual (62 pages) ,
- Instruction manual (31 pages) ,
- Manual (21 pages)
Related Manuals for XIEGU X5105
Summary of Contents for XIEGU X5105
- Page 1 XIEGU COMMUNICATION X5105 HF+50MHz Portable HF Transceiver Instructon Manual Chongqing Xiegu Technology Co.,Ltd. www.cqxiegu.com – X5105 is available in Europe at https:////www.PassioneRadio.com//...
-
Page 2: Packing List
Very small ii size aid ultra portable Packing list: ① Note RF highevoltage of antenna connector! X5105.......... 1 Power supply cable......1 Haid microphoie......1 USB Cable..........1 Service card........1 ②... - Page 3 1 X5105 Specifcatons Basic Specifcatons Frequeicy raine: Receive: 500kHz-30MHz 50MHz-54MHz Traismittiin: 160 meters -6 meters (Amateur baid oily) Operatin mode: A1A(CW)，A3E(AM)，J3E(USB/LSB)，F3E(FM) miiimum frequeicy steppiin: 1Hz Aiteiia impedaice: 50Ω Operatin temperature raine: -10℃ ~ +60℃ Frequeicy stability: afer turi oi the radio 1-60 miiutes is ± 2ppm, @25℃：1ppm/hour...
- Page 4 Seisitvity SSB/CW 500kHz-1.8MHz 10uV 1.8MHz-28MHz 0.25uV 28MHz-30MHz 0.25uV 0.35uV 50MHz-54MHz 0.25uV 0.35uV (PRE=oi，ATT=of，NB=of，NR=of，SSB/CW/AM = 10dB S/N，FM = 12dB SINAD) Imane rejectoi: 70dB If Rejectoi: 60dB Selectvity: SSB：-6dB:2.4kHz/-60dB:4.6kHz CW：-6dB:500Hz/-60dB:2000Hz AM：-6dB:6.0kHz/-60dB:25.0kHz FM：-6dB:12.0kHz/-60dB:25.0kHz Audio output: 0.6W （8Ω，≤10% THD） Audio output impedaice: 4 – 16Ω...
- Page 5 Interface defniton...
- Page 6 Whei the batery is powered for X5105, whei the batery power is about to rui out, the power iidicatoi sini oi the upper rinht corier of the screei is displayed as . At this poiit, the X5105 should be charned or switched to ai exterial power supply. Duriin the charniin process, the casiin of the machiie has a slinht fever.
- Page 7 Press these four butois to turi oi or of the correspoidiin fuictoi displayed oi the meiu area oi the curreit screei. Major tuning knob The maii tuiiin kiob of X5105, cai be used either for frequeicy renulatoi or for meius.
-
Page 8: Status Indicator
With this key, you cai iicrease curreit volume. PTT button Press aid hold this butoi, X5105 will no iito the traismit state. LOCK button If you press this butoi for a short tme, you will lock all butois aid kiobs oi the paiel;... - Page 9 Indicator color descripton: A T/R iidicator Whei the X5105 is ii receiviin mode, the iidicator linht is nreei. Whei the X5105 is ii traismittiin mode, the iidicator linht is red. B DATA iidicator Whei the data sinial or chaiiel are busy, the iidicator linht fashes.
- Page 10 Set CW messane 1(Press Set CW messane 2(Press Set CW messane 3(Press this butoi for a loin this butoi for a loin this butoi for a loin tme to eiter the CW tme to eiter the CW tme to eiter the CW messane coiteit editor) messane coiteit editor) messane coiteit editor)
- Page 11 2.2 Lef panel interface functon Lef bracket Rotate the bracket whei usiin it, whei afer usiin it, take it back to the side shield. Antenna interface Coiiect the aiteiia to the 50 ohm coaxial cable with the Q9 coiiector. IF signal output port The first IF sinial is output for use by the XDT1.
- Page 12 ACC interface The iiterface is a 8PIN micro DIN iiterface, it cai be used for exterial power amplifier, ALC coitrol, PTT coitrol, baid sinial traismissioi, it cai also be used to commuiicate with the computer for PSK commuiicatoi whei the audio sinial iiput / output. KEY interface The iiterface is 3.5mm's stereo iiterface, which cai be used to coiiect maiual / automatc telenraph keys.
- Page 13 LOCK butoi, you cai lock the host butoi aid the mouse butoi via this butoi, aid press it anaii to uilock. PTT butoi, traismittiin coitrol butoi. Move up/dowi, adjustable frequeicy iicrease, subtractoi, or selectoi of items ii the meiu. Receiviin / Traismittiin iidicator linht, microphoie operated iidicator linht. Dinital key FIL butoi, built ii filter selectoi.
- Page 14 DC power source that is curreitly coiiected to the traisceiver. 3.3 Operatng frequency band selecton The frequeicy raine of X5105 covers 0.5~54MHz. The amateur frequeicies ii this raine are divided iito multple frequeicy baids aid cai be switched ii a iumber of difereit ways. You cai complete the...
- Page 15 Operatoi method: press DN or UP key to switch to the iext or last operatoi baid respectvely. 3.5MHz 5.2MHz 14MHz 1.8MHz 7.0MHz 10MHz 50MHz 28MHz 21MHz 24MHz 18MHz The opeiiin of the 5MHz frequeicy baid is based oi the renulatois of the couitry (or renioi) where it is located.
- Page 16 Whei you do iot uiderstaid the curreit state of the aiteiia, miiimize the set traismit power value for the first tme you use the X5105 traisceiver. 3.7 Use the host PTT button X5105 comes with a PTT butoi, you cai start the traisceiver's traismissioi throunh this butoi. Operatoi method: Press this butoi to start the traismittiin fuictoi.
- Page 17 3.8 Set operatng frequency There are two ways to set the X5105 operatin frequeicy, use the bin kiob to set the frequeicy, or use the mult-fuictoi mic to set the frequeicy. Operatoi method: Use larne kiob to set frequeicy Press the butoi [<] or [>], move the cursor of the frequeicy bit to the lef or to the rinht, select the frequeicy of the desired step.
- Page 18 3.10 RIT (receive frequency trimming) Relatve to the set frequeicy, the RIT fuictoi cai set the ofset value of the actual receiviin frequeicy of the maximum ±5kHz. Operatoi method: Press [RIT] butoi to start RIT fuictoi. The rotatin kiob cai chaine the receiver frequeicy ii the raine of ±5kHz. The screei has the correspoidiin area to display the frequeicy chaine value.
- Page 19 3.12 Preamplifer // preamplifer (PRE//ATT) Pre amplifier (PRE) aid pre ateiuator (ATT) cai improve the receiver's listeiiin efect. Whei the sinial is weak, the preamplifier cai be switched oi to iicrease the sinial streinth. Whei the sinial is stroin, the preamplifier cai be switched oi to reduce the sinial streinth.
- Page 20 3.14 Pilot frequency operaton SPL and VFOA//B setng There are two iidepeideit VFO ii X5105 traisceiver, which cai set difereit frequeicies aid modes respectvely. Set the VFO reasoiably, aid with the meiu SPL fuictoi, you cai easily achieve pilot frequeicy traisceiver operatoi mode.
- Page 21 3.16 VFO mode //MEMO mode (V//M) setng Traisceiver cai switch betweei VFO mode aid MEMO mode, aid realize fexible operatoi mode. Operatoi method: Press the [V/M] butoi, you cai switch betweei the VFO mode aid the MEMO mode. Ii the curreit mode, press the [V/M] butoi, aid thei switch to aiother mode. 3.17 Lock button operaton The lock key (LOCK) cai avoid the iicorrect trinneriin of the traisceiver aid the microphoie duriin outdoor operatoi.
- Page 22 3.18 CW communicaton Operate with a haid key or ai exterial keyiin device. Operatoi method: Iisert the plun of the key (three wire) iito the KEY iiterface oi the rinht. Press the [MODE] butoi aid switch mode to CW (or CWR). Press the [MENU] butoi for a loin tme, adjust the Meiu #08 (CW DELAY) aid set the delay tme (default: 500ms).
- Page 23 Adjust storane chaiiel: If ii VFO mode, press the [V/M] butoi oi the paiel, it will eiter the chaiiel mode. Turi the kiob, you cai switch the curreit chaiiel, the chaiiel iumber will chaine accordiinly. Clear chaiiel storane: Ii the chaiiel mode, press the [MENU] butoi, switch to the third pane meiu, press the MC fuictoi key, start clear chaiiel editin.
-
Page 24: Menu System Description
3.21 The menu system can personalize the transceiver and make it more in line with your habits. Operatoi method: Press the [MENU] butoi for a secoid aid eiter the meiu mode. Press the [ V//A ] aid [ A//B ] butois to set the parameters you wait. Rotate the kiob to briin up the meiu item you wait to set. - Page 25 Use ACC plun (MINI-DIN8) to coiiect the computer audio output to X5105. The computer eid is a stereo plun. The data liie is used to coiiect the X5105 to the computer aid to eisure that the driver is properly iistalled. The HRD sofware cai coitrol the X5105 traisceiver.
- Page 26 3.24 Band data format The ACC port of the X5105 provides baid data for each baid. The baid data cai be used to coitrol the peripheral, to make automatc baid switchiin, or to ideitfy the baid iiformatoi for other devices.
- Page 27 If the product ieeds warraity repair withii two weeks of receiviin the product, XieGu will pay for the shippiin both ways. Afer two weeks XieGu will pay oily for returi shippiin.
- Page 28 Xiegu communication www.cqxiegu.com...