Advertisement
Quick Links
Compatibility
•
DVS Insert (2005)
•
DVL Insert (2005)
•
2007 Tree of Life (Rev 001) w Blower (99000153)
•
2007 Berkshire (99600113, 4) w Blower (99000153)
Make sure power to the heater has been turned off prior to installation (unplug the power cord).
Do not connect 110-120 VAC to the gas control valve or the on/off circuit on this fireplace.
IMPORTANT INSTALLATION NOTE FOR MODELS USING THE FIREBACKS:
Follow the steps below if installing the firebacks with an accent light.
DVS / DVL Installation
NOTE:
The bulb is shipped separately. Do not touch the bulb – oil or other residue left on the bulb may lead to
premature bulb failure. Use a cloth or paper towel to handle the bulb.
1
Remove the burner (see the manual for details).
2
Install the accent light as shown below.
NOTE:
the illustrations below show a DVL Insert - the accent light installs in the same manner on a DVS Insert.
NOTE: To prevent heat-damage to the
wires, make sure this clip holds the
wires down, away from the burner.
NOTE: On the DVS, make
sure to use the lower screw.
c
Route the wires from the accent light through gasket and hole. Attach the accent light cover plate
(with grommet) to the firebox floor with the screws removed in step "b". Pull the excess wire through
the grommet, towards the front of the stove (this helps prevent the wire from contacting the burner).
Page 1 of 5
Accent Light, Type 2A
•
Remove the burner (see the manual for details).
•
Install the rear fireback (see the instructions included with the firebacks).
•
Install the accent light.
•
Replace the burner.
•
Install the side firebacks (see the directions included with the firebacks).
(SKU 94400111)
Packing List
•
Accent Light Assembly (with strain relief plate)
•
Rheostat Assembly (includes Wiring Harness)
•
(2) #8 Nuts
•
Wire Nut
•
35 Watt 120 Volt T4 Halogen Bulb (G6.35 Base)
Remove this screw, position the accent
a
light assembly in the same location, and
attach with the same screw.
3/28/07
NOTE: This insulation protects
the wiring - it may be compressed
if necessary.
Remove and discard the
b
cover plate (keep the
gasket and screws).
NOTE: The cover plate is
here on the DVS.
© Travis Industries, Inc.
Advertisement
Related Manuals for Travis Industries SKU 94400111
Summary of Contents for Travis Industries SKU 94400111
- Page 1 (with grommet) to the firebox floor with the screws removed in step “b”. Pull the excess wire through the grommet, towards the front of the stove (this helps prevent the wire from contacting the burner). Page 1 of 5 3/28/07 © Travis Industries, Inc.
- Page 2 (use wireties if necessary). Install the bulb into the accent light (take care to not touch the bulb). Restore the firebox to the correct configuration (replace the burners, etc.). Page 2 of 5 3/28/07 © Travis Industries, Inc.
- Page 3 (this helps prevent the wire switch the thermodisk to the mounting position on the left side. from contacting the burner). Page 3 of 5 3/28/07 © Travis Industries, Inc.
- Page 4 (use wireties if necessary). Install the bulb into the accent light (take care to not touch the bulb). Restore the firebox to the correct configuration (replace the burners, etc.). Page 4 of 5 3/28/07 © Travis Industries, Inc.
-
Page 5: Bulb Replacement
The accent light must be replaced with 35 Watt 120 Volt T4 Halogen Bulbs (G6.35 Base) – available at most hardware stores. To replace the bulb, simply remove it from the socket and insert the new bulb (pin orientation does not matter). Page 5 of 5 3/28/07 © Travis Industries, Inc.
Need help?
Do you have a question about the SKU 94400111 and is the answer not in the manual?
Questions and answers