Download Print this page

Travis Industries DVS EG Firebacks Installation Instructions

Advertisement

Quick Links

SKU Numbers
DVS Firebacks
Straight Brick/Herringbone
Handmade Brick/Graystone
Black Glass
Ledgestone
Compatibility
DVS EmberGlo™ Inserts – (starting 2020)
DVL EmberGlo™ Inserts – (starting 2020)
Packing List
(1) Rear Fireback
(2) Side Firebacks
Installation
WARNING
Turn off gas to the appliance and make sure it has fully cooled prior to conducting service.
HANDLING THE FIREBACKS: The glass firebacks are fragile – especially the edges. Take care to prevent
contacting/scraping the glass against metal or rough surfaces. You may wish to lay out a blanket during
installation in case you need to set the firebacks down.
We recommend the use of gloves and safety glasses during the installation of the glass firebacks.
GLASS FIREBACK CLEANING
These firebacks require periodic cleaning. Do not use ammonia-based cleaners (this may cloud the glass). We
recommend ammonia-free glass cleaner (i.e. vinegar and water) to clean the fireback.
The rear fireback is rectangular and must be placed right side up. Lay the firebacks on a flat
surface prior to installing to verify the texture (brick, ledgestones) are aligned.
The firebacks are fragile, especially after being exposed to heat. Take care to prevent contacting/scraping the
firebacks against metal or rough surfaces.
NOTE On two-sided firebacks make sure the rear and sides patterns match.
NOTE On rear firebacks that have brick texture make sure the edge with the full brick is at the top.
1. Access the firebox (see Owner's Manual).
2. There are (2) fireback clips in the
firebox ceiling for DVS (1) on each
side and (3) for DVL– (1) on each
side and (1) in the back. Use a ¼" nut
driver to loosen the screws just
enough to allow the fireback clip to
move. The clip has a "keyhole" slot
on it. Slide the clip forward until it can
move freely over the head of the
screw. Tighten the screws so they do
not obstruct the installation of the
fireback panels in a later step.
Page 1 of 4
DVS/DVL EG Firebacks
sku# 96100473
sku# 96100474
sku# 96100475
sku# 96100476
Tools Needed
(2) Short - Top Fireback Clips (For Glass Firebacks ONLY)
(2) Long -Bottom Fireback Clips (For Glass Firebacks ONLY)
GLASS FIREBACK WARNINGS
CERAMIC FIREBACK WARNINGS
Loosen Screw
17602176 - 9/14/20
DVL Firebacks
Straight Brick/Herringbone
Handmade Brick/Graystone
Black Glass
Ledgestone
¼" Nut Driver
Fireback Clip
sku# 96100483
sku# 96100484
sku# 96100485
sku# 96100486
TIghten Screw
Travis Industries, Inc.

Advertisement

loading
Need help?

Need help?

Do you have a question about the DVS EG Firebacks and is the answer not in the manual?

Questions and answers

Summary of Contents for Travis Industries DVS EG Firebacks

  • Page 1 Slide the clip forward until it can move freely over the head of the screw. Tighten the screws so they do Fireback Clip not obstruct the installation of the fireback panels in a later step. Page 1 of 4 17602176 - 9/14/20 Travis Industries, Inc.
  • Page 2 4. Place the rear fireback into position and support the back of the firebox it with your hand until you install the rear fireback clip in the next step. Page 2 of 4 17602176 - 9/14/20 Travis Industries, Inc.
  • Page 3 Support the rear fireback with your hand until at least one side fireback is in place (next step). Page 3 of 4 17602176 - 9/14/20 Travis Industries, Inc.
  • Page 4 10. Reinstall the burner side covers removed in step 3. NOTE: Slide the side burner covers toward the sides of the unit until they contact the side firebacks. Tighten the screws to hold them in place. Page 4 of 4 17602176 - 9/14/20 Travis Industries, Inc.

This manual is also suitable for:

Dvl eg firebacks9610047396100483961004749610048496100475 ... Show all