EXCELL PRECISION CO., LTD. Table of Contents PRECAUTIONS FOR USE ....................2 PREPARING TO USE THE SCALE ..................2 CHAPTER 1 INTRODUCTION .................... 4 1-1 F ........................4 EATURES 1-2 D ....................5 ISPLAY ESCRIPTION 1-3 K ................. 6 EYPAD...
EXCELL PRECISION CO., LTD. Thank for your purchasing of our EXCELL Weighing Scale. To guide you to use our product correctly, please read this User Manual carefully to extend the life of machine and to avoid error. Precautions for Use Please keep scale in a cool and dry place.
Page 4
EXCELL PRECISION CO., LTD. Due to the storage battery adopt the advanced free-maintaining technique, customers need not to replenish electrolyte. The scale should be recharged every 3 months to prevent failure of the internal rechargeable battery. The battery should be charged for 8~10 hours.
EXCELL PRECISION CO., LTD. Chapter 1 Introduction 1-1 Features 1. High performance A/D converter 2. According to different resolution to do linearity calibration Ordinary resolution models (below 10000) Do specification calibration first then do weight calibration High resolution models (10000~30000) Do linearity calibration first...
EXCELL PRECISION CO., LTD. 1-2 Display Description High limit value OK value (The value between HI and LO limit value) Low limit value “Zero” indication “Net weight” indication “Low battery power” indication “Stable” indication “Pre-tare mode” indication “Totalizing mode” indication No function “Samples insufficient”...
EXCELL PRECISION CO., LTD. 1-3 Keypad Functions Description Press this key to select the required unit from the preset units. Press this key to preset the weight and quantity. Press this key to accumulate the weight value or others. Press this key to tare (deduct the container weight) Press this key to preset tare value.
EXCELL PRECISION CO., LTD. 1-4 Power Description Power Selection 1. 6 V / 4 Ah Rechargeable battery 2. 100~240 V AC Power Consumption Indicator + L/C + no backlight 27 mA indicator+ L/C + front display 37 mA backlight Low Power Alarm...
EXCELL PRECISION CO., LTD. Chapter 2 General Operation Description 2-1 Backlight Function Press key to select the display backlight mode: “Auto Backlight” mode. When the weight is over 10d or any key is pressed, the display backlight will be switched on. When the weight returns to zero (the weight on platform is less than 10d), the display backlight will switch off after 10 seconds.
Page 10
EXCELL PRECISION CO., LTD. Preset “Beeper value” ( Refer to NOTE ) e.g. Beeper value = 22 Press key 1 time the display shows Press key 2 times the display shows Press key 1 time the display shows ...
Page 11
EXCELL PRECISION CO., LTD. Alarm Mode Settings: Sets High Limit (weight alarm limit). Low Limit is disabled (you can be freely set any Low Limit value without any effect). The beeper setting is 32. A When weight alarm limit is reached, RelayCard (HIGHT) is activated with one weight totalizing.
EXCELL PRECISION CO., LTD. 2-2-3 Totalizing 1. Weight Totalizing Place goods on the platter, after stable and press key to save the weight value. Then the display shows the total number of additions and the totalized weight value. And the (M+) indication “” will flash on the display. The indicator will recover to show the weight value of the goods on the platter after 3 seconds and the (M+) indication “”...
EXCELL PRECISION CO., LTD. 2-2-5 Tare Function 1. When the weight of the container is unknown ( Place the container on the platter, after stable and press key, the weight value returns to zero and net indication (Net) is on.
EXCELL PRECISION CO., LTD. 2-3 Counting Function 2-3-1 Sampling Press key to select sample quantity from 10, 20, 50,100 and the display shows accordingly. Select sample quantity and then place samples on the platter, and then press key, the display shows “...
EXCELL PRECISION CO., LTD. Chapter 3 General Function Setting Switch on the scale. While the scale is counting down to zero, press and hold until the display shows the software program version number Release the key, the scale enters into the configuration setting mode and is showed on the display.
EXCELL PRECISION CO., LTD. Check Weighing Configurations If is set, accessing to is denied. key to select F4 function the display shows Press Press key for 5 times to clear HI, OK, LO values ...
EXCELL PRECISION CO., LTD. RS-232 Interface Output Setting (option) function the display shows key to select key = Increase the flash value by one (from 0 to 8) or Press selecting baud rate from 1 200, 2 400,4 800 and...
Page 18
EXCELL PRECISION CO., LTD. RS-232 Interface Format I . Mode: UART Signal of EIA-RS0232 C II . Format : 1. Baud rate : 1 200, 2 400, 4 800, 9 600 bits/second 2. Data bits : 8 bits 3. Parity bit : None 4.
Page 19
EXCELL PRECISION CO., LTD. HEAD1 ( 2 BYTES ) HEAD2 ( 2 BYTES ) OL - Overload , Under load TR - TARE Mode ST - Display is Stable NT - NET Mode US - Display is Unstable GS -...
Page 21
EXCELL PRECISION CO., LTD. Stable Transmission (totalizing mode) WT/UNIT ( kg / lb ) - - - - - - - - - - - - - - The scale is stable 0001 1.0000 The scale is stable 0002 1.0000...
Page 22
EXCELL PRECISION CO., LTD. Continuous Transmission (specific form) (Brazil customer) The print out is as below: If display shows 70.15kg, the RS-232 export is 51.07000 If display shows -70.15kg, the RS-232 export is 51.0700- If display shows OL, then RS-232 print nothing.
EXCELL PRECISION CO., LTD. Exit Function Setting Mode key to select F6 function the display shows Press Counting down to zero and exit setting mode Internal Value Display Mode key to select F7 function the display shows...
EXCELL PRECISION CO., LTD. Hold Mode key to select F8 function the display shows You can set RS232 to print the HOLD value on display (after making appropriate settings, press to print). Press Press Press Press Press...
Page 25
EXCELL PRECISION CO., LTD. = Hold function disabled = “Peak hold” mode Holds and displays relative maximum weight when the weight is continually Changing To exit this mode, press any key except the key. = “Stable hold 1” mode When the weight is stable, the LCD holds the currently displayed weight...
Page 26
EXCELL PRECISION CO., LTD. Animal Scale Hold settings Select hold 4 and press Press Permitted Deviation Range keys to set. Enter a range between 1% and 100%. The default range is 10%. Press Number of Samples to Take an Average keys to set.
EXCELL PRECISION CO., LTD. ID Code Setting , , (Use must be in coordination with key to select F11 function the display shows key or Press Machine ID code setting: Press to set 01 ~ 99 Default setting: 00 (1) “00”: RS-232 does not transmit Machine ID...
Page 28
EXCELL PRECISION CO., LTD. Print Key ( ) Function Setting key to select F12 function the display shows key or Press to set 0 ~ 2 Default setting: 0 Press Press key to print current weight if weight variation is within ±1d ~ ±10d, or to print accumulated weight if weight variation is over...