Table of Contents
Advertisement
EXCELL PRECISION CO., LTD
.
USER MANUAL
© Excell Precision Limited 2006. All rights reserved Worldwide.
The information contained herein is the property of Excell Precision Limited and is
supplied without liability for errors or omissions. No part may be reproduced or used
except as authorised by contract or other written permission. The copyright and the
foregoing restriction on reproduction and use extend to all media in which the
information may be embodied.
Counting
ZSME200000003
Advertisement
Table of Contents
Related Manuals for Excell Counting Scale
Summary of Contents for Excell Counting Scale
-
Page 1: User Manual
USER MANUAL © Excell Precision Limited 2006. All rights reserved Worldwide. The information contained herein is the property of Excell Precision Limited and is supplied without liability for errors or omissions. No part may be reproduced or used except as authorised by contract or other written permission. The copyright and the foregoing restriction on reproduction and use extend to all media in which the information may be embodied. -
Page 3: Table Of Contents
EXCELL PRECISION CO., LTD TABLE OF CONTENTS INSTRUCTIONS FOR USE...3 PREPARING TO USE THE SCALE...3 CHAPTER 1 PRODUCT INTRODUCTION ...4 1-1 DISPLAYS ...4 1-2 KEYBOARD FUNCTION ...6 1-3 POWER SOURCES ...9 CHAPTER 2 OPERATION ...10 2-1 SWITCH SCALE ON...10 2-2 SWITCH SCALE OFF...10 2-3 DISPLAY BACKLIGHT ...10... - Page 4 EXCELL PRECISION CO., LTD CHAPTER 4 KEYBOARD TYPES ...26 4-1 STANDARD TYPE...26 4-2 TYPE I DUAL WEIGHING UNIT...27 4-2-1 Unit Selection...27 4-2-2 Quantity Preset ...27 4-2-3 Weight Preset ...28 4-3 TYPE II UNIT WEIGHT PRESET ...29 4-3-1 Unit Weight Preset Stores...29 4-3-2 Quantity Preset ...30...
-
Page 5: Instructions For Use
4) The load placed on the weigh pan must not exceed the maximum weighing capacity of the scale. 5) If the scale is not going to be used for some time, please clean it and store it in a plastic bag in dry conditions. A desiccant sachet may be included to prevent moisture build up. -
Page 6: Chapter 1 Product Introduction
..PERFORMANCE: High Precision Counting Scale (1/15,000 and 1/ 30,000 Display Resolution) Minimum Sampling Weight = at least 20d. Minimum Unit Weight = at least 0.2d Standard Counting Scale (1/6,000 Display Resolution) Minimum Sampling Weight = at least 40d. Minimum Unit Weight = at least 0.8d... - Page 7 EXCELL PRECISION CO., LTD (d=division) Counting ZSME200000003...
-
Page 8: Keyboard Function
EXCELL PRECISION CO., LTD 1-2 KEYBOARD FUNCTION STANDARD TYPE ADDITIONAL FUNCTIONS TYPE I SMPL Counting Q’TY SMPL This is a “CLEAR” key to delete all the High UNIT Limit values. Please W.T. refer to page 21. Dual Weighing Unit Q’TY This Key is to select weight units of “lb”or... - Page 9 EXCELL PRECISION CO., LTD ADDITIONAL FUNCTIONS TYPE II Counting Unit Weight Preset Q’TY SMPL This key selects 10 pre-set stores of piece weight. UNIT U.W. Please refer to page 24. W.T. This key selects 10 pre-set ..
- Page 10 EXCELL PRECISION CO., LTD COMBINATION TYPE Weight Stores Counting Dual Weighing Units + Preset Piece Q’TY SMPL This is a dual function key UNIT U.W. which selects: W.T. Preset piece weight stores and weighing units selection. Please refer to page 27.
-
Page 11: Power Sources
If the scale is not recharged after the low battery symbol is displayed, the scale will switch itself off after 20-30 minuets. -
Page 12: Chapter 2 Operation
CHAPTER 2 OPERATION 2-1 SWITCH SCALE ON To switch on the scale, ensure that the weigh pan is empty and press the ON/OFF ”) position and the scale will power on and set zero ready for switch towards the (“... -
Page 13: Sampling Speed & Back To Zero Setting
& other unstable environments a useful additional facility is available. With the zero display mask it is possible to configure the scale not to show the first division of the weight. When configured the weight display will show zero as long as the weight is less than two display divisions. -
Page 14: Auto Calibration
Enter the weight value to be used and then place the weight on the scale, when the reading is stable the scale will automatically calibrate. While the scale is counting back to zero, remove all the weights from the scale. The Calibration procedure is finished. The new calibration will be stored and recalled when the scale is switched off and on again. -
Page 15: Unit Weight Calibration
2.8g, then because the difference between the to unit weights is greater than 10% the scale will average the two values and set a new unit weight of 2.65g. If the difference in unit weights are less than 10% then the unit weight is not re-calculated. -
Page 16: Counting
Ž When the quantity display is flashing, press the Sampling Weight • Once the scale stabilizes, the count is shown on the quantity display. Sampling Weight 2-8-2 The Unit Weight of Object is Known Œ Enter the known weight of the item... -
Page 17: Deduction Of Container Weight
Œ Place the container onto the scale. Container Weight • Press T Key. Ž Once the scale stabilizes, it will display the net weight and the “3” icon next to the NET symbol will be displayed. 2-9-2 Clear Tare Value When the container is removed from the scale, the weight display will show a negative sign. -
Page 18: The Weight Container Is Known (Pre-Set Tare)
2-9-3 The Weight Container is Known (Pre-set Tare) The User mode function to operate the “Pre-set tare” is to set “0” not perform a pre-set tare when there is a weight on the scale. Œ Nothing is placed on the scale. -
Page 19: Clear The Pretare Value
EXCELL PRECISION CO., LTD 2-9-4 Clear The Pretare Value When the container is removed from the scale, the weight display will show a negative sign. Press the T key to clear pre-tare value and the weight display will reset to zero, the “3” icon adjacent to the NET symbol will go off. -
Page 20: Totalising
Œ Place a desired object onto the scale Object Weight • Press M+ Key Ž Once the scale is stable. Total Weight Totalised • After 3 seconds, the scale will return to the counting mode. Object Weight Counting Unit Weight Object Q’ty Placed on Scale... -
Page 21: Recall Quantity Totalised
With both the weight and the unit weight displaying zero, press totalised value. Total Weight Totalised 2-10-3 Weight Totalising Œ With the unit weight display showing zero, place an object onto the scale. Object Weight • Press M+ key. Ž Once the scale has stabilized. -
Page 22: Clear All Totalised Values
Press the MC key to clear all of the totalised values and the “3” symbol adjacent to the M+ icon on the overlay will switch off. The totals for weight, number of additions and quantity are all cleared back to zero. NOTE: All totals will be lost if the scale is switched off. Counting ZSME200000003... -
Page 23: Chapter 3 User Interface Setting
Press to select the required mode Pre-set Tare function is not available when there is an object on the scale. Pre-set Tare function is available when there is an object on the scale. To exit and save the entry, press the Counting twice. -
Page 24: Pre-Set Quantity Conditions
Press to select the required mode 0 = The quantity will be accepted by the scale only when the weight is stable. 1 = The quantity will be accepted by the scale even if the weight is un-stable. To exit and save the entry, press the... -
Page 25: M+ Continuous Operation (Only After Return To Zero)
Weight Press to select the required mode 0 = After M+ operation, next M+ operation is allowed only after the scale Returns to Zero. 1 = After M+ operation, next M+ operation is allowed immediately, without the scale Returning to Zero. - Page 26 EXCELL PRECISION CO., LTD the scale. Counting ZSME200000003...
-
Page 27: Baud Rate Setting (For Only With The Serial Interface)
EXCELL PRECISION CO., LTD 3-7 BAUD RATE SETTING (for only with the serial interface) Press then Weight Press to select the required baud 0 = 1200 1 = 2400 2 = 4800 3 = 9600 To exit and save the entry, press the... -
Page 28: Chapter 4 Keyboard Types
CHAPTER 4 KEYBOARD TYPES 4-1 STANDARD TYPE 4-1-1 Quantity Preset The scale can store a Hi Limit quantity value. The scale will make a warning beep and the unit weight window will display a blinking over the Hi limit alarm value set. -
Page 29: Type Idual Weighing Unit
4-2-2 Quantity Preset The scale can store a Hi Limit quantity value. The scale will make a warning beep and the unit weight window will display a blinking over the Hi limit alarm value set. -
Page 30: Weight Preset
EXCELL PRECISION CO., LTD 4-2-3 Weight Preset The scale can store a Hi Limit unit weight value. The scale will make a warning beep and the unit weight window will display a blinking if the unit weight is over the Hi limit value stored. -
Page 31: Type Ii Unit Weight Preset
4-3 TYPE II UNIT WEIGHT PRESET 4-3-1 Unit Weight Preset Stores The scale can store 10 sets of unit weight presets. The stores are accessed using the number keys ( display will show the unit weight previously saved in that store. -
Page 32: Quantity Preset
EXCELL PRECISION CO., LTD 4-3-2 Quantity Preset The scale can store a Hi Limit quantity value. The scale will make a warning beep and the unit weight window will display a blinking over the Hi limit alarm value set. Hi Limit Value for Quantity Preset Œ... -
Page 33: Weight Preset
EXCELL PRECISION CO., LTD 4-3-3 Weight Preset The scale can store a Hi Limit unit weight value. The scale will make a warning beep and the unit weight window will display a blinking if the unit weight is over the Hi limit value stored. -
Page 34: Combination Type Dual Weighing Unit + Unit Weight Preset
(If the unit selection setting is a secondary function, press the combination key for about 3 seconds and the display will show the following) Remarks : The scale will save the current unit in use. At power on the last units in use will be used. Counting DUAL WEIGHING UNIT + Q’TY... -
Page 35: Unit Weight Preset Stores
EXCELL PRECISION CO., LTD 4-4-2 Unit Weight Preset Stores The scale can store 10 sets of unit weight presets. The stores are accessed using the number keys ( display will show the unit weight previously saved in that store. Set Unit Weight Preset Œ... -
Page 36: Quantity Preset
EXCELL PRECISION CO., LTD 4-4-3 Quantity Preset The scale can store a Hi Limit quantity value. The scale will make a warning beep and the unit weight window will display a blinking over the Hi limit alarm value set. Set the Hi Limit Value for Quantity Preset Œ... -
Page 37: Weight Preset
EXCELL PRECISION CO., LTD 4-4-4 Weight Preset The scale can store a Hi Limit unit weight value. The scale will make a warning beep and the unit weight window will display a blinking if the unit weight is over the Hi limit value stored. -
Page 38: Chapter 5 Interface
Press key and the display window will not show the totalised value as the buzzer will beep. Press the key to exit the setting mode and the scale will return to counting mode. Counting UNIT WEIGHT UNIT WEIGHT UNIT WEIGHT... -
Page 39: Preset Tare Operation Conditions
Preset tare is not allowed if there is a weight on the scale. Preset tare will operate at any point throughout the weighing range. Press the key to exit the setting mode and the scale will return to counting mode. Counting UNIT WEIGHT... -
Page 40: Quantity Preset Operation Conditions
The “Q’TY PST” will only operate when the weight is stable. The “Q’TY PST” will operate irrespective of the stability of the weight. Press the key to exit the setting mode and the scale will return to counting mode. Counting UNIT WEIGHT... -
Page 41: Totalising Operation Conditions
Totalising will only be carried out when the weight is stable. Totalising will be carried out irrespective of the stability of the weight. Press the key to exit the setting mode and the scale will return to counting mode. Counting UNIT WEIGHT... -
Page 42: The Condition To Allow The Next Totalising Operation
The weight needs to return to zero before the next totalising operation is allowed. Allow next totalising operation without return to zero interlock. Press the key to exit the setting mode and the scale will return to counting mode. Counting UNIT WEIGHT UNIT WEIGHT... -
Page 43: Combination Key Operation Mode
Press the “Unit Weight Preset” function key (main function) and hold it down for 3 seconds, the unit selection function becomes the secondary function. Press the key to exit the setting mode and the scale will return to counting mode. Counting UNIT WEIGHT... -
Page 44: Baud Rate Setting
WEIGHT Use number keys 0 to 3 key to select Once the setting is done, re-start the scale by turning the power off / on. Press the key to exit the setting mode and the scale will return to counting mode. -
Page 45: Transmit Mode Selection
Use the number keys 0 to 3 to select Press Stream transmit Once the setting is done, re-start the scale by turning the power off / on. Press the key to exit the setting mode and the scale will return to counting mode. - Page 46 EXCELL PRECISION CO., LTD NO. No. of totalising operations N/W Net Weight U/W Unit Weight PCS Piece T/N Total no. of totalising operations T/W Total Weight T/A Total Amount Counting ZSME200000003...
Need help?
Do you have a question about the Counting Scale and is the answer not in the manual?
Questions and answers