Related Manuals for Keysight N5222-60118
Summary of Contents for Keysight N5222-60118
- Page 1 Installation Note Keysight Add 4-Port Capability Upgrade Kit To Upgrade PNA N5221B or N5222B Option 217 to Option 417 Upgrade Kit Order Number: N5221BU- 617 and N5222BU- 617 Keysight Kit Number: N5222-60118...
- Page 2 DOCUMENT OR ANY INFORMATION reproduce, release, perform, CONTAINED HEREIN. SHOULD display, or disclose commercial KEYSIGHT AND THE USER HAVE A SEPARATE WRITTEN AGREEMENT computer software or WITH WARRANTY TERMS commercial computer software COVERING THE MATERIAL IN THIS...
- Page 3 Keysight Add 4-Port Capability Upgrade Kit Upgrade Kit Number: N5222-60118 Installation Note Description of the Upgrade This upgrade converts your N5221B or N5222B Option 217 2-port analyzer to a N5221B or N5222B Option 417 4-port analyzer by adding: — an additional source —...
- Page 4 Getting Assistance from Keysight Installing this upgrade kit requires special skills and experience. If you think you may not be qualified to do the work, or need advice, contact Keysight. Contacting Keysight Assistance with test and measurements needs and information on finding a local Keysight office are available on the Web at: http://www.keysight.com/find/assist...
- Page 5 The enclosed Software Entitlement Certificate is a receipt, verifying that you have purchased a licensed option for the PNA of your choice. You must now use a Keysight Web page to request a license key file for the instrument that will receive the option.
- Page 6 Using the information just gathered, you must request license key(s) from the Keysight Software Manager: http://www.keysight.com/find/softwaremanager. You will need to provide an email address, to which Keysight will promptly email your license key file. Refer to “License Key Redemption” on page...
- Page 7 21 in-lb. About Installing the Upgrade Products affected N5221B and N5222B Option 217 Installation to be performed by Keysight service center or personnel qualified by Keysight Estimated installation time 5 hours Estimated adjustment time 0.5 hours...
- Page 8 Items Included in the Upgrade Kit Items Included in the Upgrade Kit Check the contents of your kit against the following list. If any part is missing or damaged, contact Keysight Technologies. Refer to “Getting Assistance from Keysight” on page...
- Page 9 Items Included in the Upgrade Kit Table 1 Contents of Upgrade Kit N5222-60118 Description Part Number Desig. Front panel overlay (label), 4-port, Option 417 N5222-80014 Test set front plate, 4-port N5221-00007 Cable-tie self-locking wide nylon gray 1400-0249 Dust caps for test ports...
-
Page 10: Table Of Contents
Items Included in the Upgrade Kit Table 1 Contents of Upgrade Kit N5222-60118 Description Part Number Desig. RF cable, Front panel jumper N5222-20091 RF cable, A21 HMA26.5 to A22 splitter N5222-20009 RF cable, A22 splitter to A23 mixer brick N5222-20007... -
Page 11: Cable Clamp
Items Included in the Upgrade Kit Table 1 Contents of Upgrade Kit N5222-60118 Description Part Number Desig. Ribbon cable, A19 test set motherboard J203 to A36 port 4 source attenuator N5242-60008 Extra quantities of items such as protective plastic caps, screws, cable ties, and cable clamps may be included in this upgrade kit. -
Page 12: N5222
Installation Procedure for the Upgrade Installation Procedure for the Upgrade The network analyzer must be in proper working condition prior to installing this option. Any necessary repairs must be made before proceeding with this installation. This installation requires the removal of the analyzer’s protective outer covers. -
Page 13: Software Entitlement Certificate 1
If the model number, serial number, or option number do not match those on your license key, you will not be able to install the option. If this is the case, contact Keysight for assistance before beginning the installation of this upgrade. Refer to “Contacting Keysight”... - Page 14 Installation Procedure for the Upgrade Step 2. Remove the Outer Cover For instructions, click the Chapter 7 bookmark “Removing the Covers” in the PDF Service Guide Step 3. Remove the Inner Cover For instructions, click the Chapter 7 bookmark “Removing the Covers” in the PDF Service Guide Step 4.
-
Page 15: N5242
Installation Procedure for the Upgrade — W64 (N5242-60025) A23 mixer brick (R1) to A20 IF multiplexer (P601) — W65 (N5242-60026) A23 mixer brick (R2) to A20 IF multiplexer (P801) — W62 (N5247-60023) A20 IF multiplexer board P603 to A12 SPAM board J2 (2-port) —... -
Page 16: N5222
Installation Procedure for the Upgrade Figure 1 A24 Mixer Brick Assembly Installation Note N5222-90118... -
Page 17: N5222
Installation Procedure for the Upgrade Figure 2 A24 Mixer Brick Block Assembly (cont.) Installation Note N5222-90118... -
Page 18: N5222
Installation Procedure for the Upgrade Step 9. Assemble the A26 and A27 Receiver Coupler Assemblies Follow the instructions shown in Figure 3. New parts are listed in Table 1 on page 8 of this document. Figure 3 A26 and A27 Receiver Coupler Assemblies Installation Note N5222-90118... -
Page 19: N5222
Installation Procedure for the Upgrade Step 10. Install the A23/A24 Mixer Brick Block Assembly Follow the instructions shown in Figure 4. New parts are listed in Table 1 on page 8 of this document. Figure 4 Mixer Brick Block and Receiver Coupler Assemblies Installation Step 11. -
Page 20: N5222
Installation Procedure for the Upgrade Step 12. Assemble the A35 and A36 Source Attenuators and the A43 and A44 Receiver Attenuators Follow the five instructions shown in Figure Figure 5 A35, A36 Source Attenuators Assembly and A43, A44 Receiver Attenuators Assembly Installation Note N5222-90118... -
Page 21: N5222
Installation Procedure for the Upgrade Step 13. Install the A35 and A36 Source Attenuators and the A43 and A44 Receiver Attenuators Follow the instructions shown in Figure Figure 6 A35, A36 Source Attenuators Assembly and A43, A44 Receiver Attenuators Installation Installation Note N5222-90118... -
Page 22: N5222
Installation Procedure for the Upgrade Step 14. Assemble the A29 - A32 Test Port Coupler Assemblies 1. Remove the A29 test port 1 coupler and A32 test port 2 coupler from the PNA. For instructions, click the Chapter 7 bookmark, “Removing and Replacing the A29 - A32 Test Port Couplers”... -
Page 23: N5222
Installation Procedure for the Upgrade Step 15. Install the LED Boards, Bulkhead Connectors, and Test Port Coupler Assemblies to the 4-Port Test Set Front Plate 1. Remove two screws from each LED board and remove the boards from the 2-port test set front plate of the PNA. Keep the screws and LED boards for reuse later. -
Page 24: N5222
Installation Procedure for the Upgrade Step 16. Install the Bulkhead Connectors in the Test Set Front Plate Refer to Figure 9 for this procedure. New parts are listed in Table 1 on page 1. Locate the bulkhead connectors you removed earlier from the 2-port test set front plate of the PNA. -
Page 25: N5222
Installation Procedure for the Upgrade Step 17. Install the 4-Port Coupler Plate Assembly to the Deck Follow the four instructions shown in Figure Figure 10 Coupler Plate Assembly Installation Installation Note N5222-90118... - Page 26 Installation Procedure for the Upgrade Step 18. Assemble the A8 26.5 GHz Source 2 Assembly Follow the three instructions shown in Figure Figure 11 A8 Source 2 Assembly Installation Note N5222-90118...
- Page 27 Installation Procedure for the Upgrade Step 19. Install the A8 26.5 GHz Source 2 Assembly Follow the three instructions shown in Figure Figure 12 A8 Source 2 Assembly Installation Installation Note N5222-90118...
-
Page 28: N5242
Installation Procedure for the Upgrade Step 20. Install the A13 13.5 GHz (Source 2) Synthesizer Board and Cables 1. Install new gray cable W67 (N5242-60030) to connector J5 of the new A13 (source 2) synthesizer board (N5240-60074). The loose end of the cable will be connected on the A10 frequency reference board (J7) after the A13 board has been installed in the analyzer. -
Page 29: N5242
Installation Procedure for the Upgrade — W55 (N5242-60024) A24 mixer brick (D) to A20 IF multiplexer (P801) — W56 (N5242-60019) A24 mixer brick (R4) to A20 IF multiplexer (P414) — W57 (N5242-60020) A24 mixer brick (R3) to A20 IF multiplexer (P413) —... -
Page 30: N5222
Installation Procedure for the Upgrade Figure 13 Information to Secure W35 and W36 — W35 (reuse) (N5222-20033) A33 reference mixer switch to front-panel REF 1 SOURCE OUT * Refer to the note shown in Figure 13 for information on installing W35 (part number N5222-20033). -
Page 31: N5222
Installation Procedure for the Upgrade Figure 14 Location of Cable Clamps to Secure W49 — W48 (N5222-20101) A33 reference mixer switch to A23 mixer brick (R1) * As shown in Figure 15 on page 32, install three cable ties (part number 1400-0249) to secure W48 (part number N5222-20101). -
Page 32: N5222
Installation Procedure for the Upgrade Figure 15 Location of Cable Ties to Secure W48 — W88 (reuse) (N5222-20004) A42 port 1 receiver attenuator to A23 mixer brick (A) — W13 (reuse) (N5222-20005) A25 port 1 receiver coupler to A33 reference mixer switch * If the screws that attach the reference mixer switch to the test set deck were loosened, torque these screws now to 9 in-lbs. -
Page 33: N5222
Installation Procedure for the Upgrade Step 22. Reinstall the A19 Test Set Motherboard For instructions on reinstalling the board, click the Chapter 7 bookmark “Removing and Replacing the A19 test set motherboard” in the PDF Service Guide Step 23. Install Cables on the A19 Test Set Motherboard Follow instructions carefully when making cable connections, especially wire harness connections. -
Page 34: N5222
Installation Procedure for the Upgrade 3. Reassemble the front panel’s lower dress panel assembly with the new 4-port front frame (N5240-00009) by reversing the order of step 2 in the instructions previously followed. IMPORTANT! To avoid possible damage to the lower front panel overlay (label), do not attempt to attach the lower front panel label until “Step 26. - Page 35 Installation Procedure for the Upgrade Step 26. Install the Overlay To see an image of the front panel overlay (N5222-80014) click the Chapter 6 bookmark “Front Panel Assembly, Front Side, All Options” in the PDF Service Guide . New parts are listed in Table 1 on page 1.
- Page 36 2. Right click the on the desired option and click Delete. 3. In the Select Desired Option list, click 217. 4. In the Keysight License Manager dialog box that appears, press or click Yes to confirm delete. 5. A message displays stating that the option removal was successful.
- Page 37 — The analyzer must be powered up and operating to perform this procedure. — The Network Analyzer program must be running. — Refer to the license message you received from Keysight: Verify that the analyzer’s model and serial numbers match those on the license message you received from Keysight.
- Page 38 2. Verify that “417” are listed, but “217” is not listed after “Options:” in the display. Click OK. If the options have not been enabled or if the option 217 license has not been removed, contact Keysight Technologies. Refer to “Getting Assistance from Keysight” on page...
- Page 39 PDF Service Guide If you experience difficulty with the basic functioning of the analyzer, contact Keysight. Refer to “Contacting Keysight” on page Calibration Although the analyzer functions, its performance relative to its specifications has not been verified. It is recommended that a full instrument calibration be performed using the analyzer’s internal performance test software.
- Page 40 Installation Procedure for the Upgrade Step 34. Prepare the PNA for the User 1. If necessary, reinstall front jumper cables. 2. Install the cable guards, pushing them over the front jumper cables until the cushioning material touches the front panel of the PNA. 3.
- Page 41 Installation Note Xxxxx-xxxxx...
- Page 42 This information is subject to change without notice. © Keysight Technologies 2000-2017 Edition 2, May 2017 www.keysight.com...