Advertisement
Quick Links
Advertisement
Related Manuals for Morris MDM-3018
Summary of Contents for Morris MDM-3018
- Page 1 MULTIFUNCTIONAL AIR TREATMENT UNIT MANUAL MODEL MDM-3018...
- Page 2 VERY IMPORTANT Do not install and use your portable Air Treatment Unit before carefully reading this instruction guide. Please retain this manual brochure for product warranty and future reference CAUTION 1. " PLEASE MAKE SURE THE PRODUCT VENTILATES ALL THE TIME "! Please make sure the inlet and outlet ventilation is not blocked at all times.
- Page 3 9. When turning on the unit at the first time, the cool air outlet stepper motor will operate and then the fan motor and the compressor will start up. The compressor will work after 3.5 minutes operating hereafters. 10. When the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard.
-
Page 4: Remote Control
ATTENTION For effective hot air and cooling functions, please ensure that the following steps are undertaken: Extend the exhaust hose to a length of not more than 400mm. The exhaust hose must be kept parallel and must not be bent up or down. - Page 5 - Moves easily from room to room on easy glide castors - No installation required-just plug into any household power outlet - Powerful refrigerated air system cools down the ambience instantly whenever you want. - Dehumidified and filtered air cycle improve breathing environments effectively.
-
Page 6: Table Of Contents
CONTENTS 1 / Air conditioner unit 2 / Remote control 3 / User manual 4 / Window Kit A NAME OF THE PARTS Control panel Remote control receiver Filter of EVA Air outlet Air inlet(left) Joint tube Exhaust hose Remote control location Filter of COND 10. -
Page 7: Control Panel
CONTROL PANEL & DESCRIPTION OF FUNCTION... - Page 8 1. POWER Press to turn unit "ON" or "OFF" FUNCTION Press this key to select dehumidifying, cooling, , humidifying, air delivery or heating air purification. 3. TEMPERATURE REGULATION KEY During cooling function：This key raises the preset temperature by 1℃ each time it is pressed and the maximum limit is 30℃.
- Page 9 ※ The display is also used to show error codes should a fault occur, see ERROR CODES. SPEED Press to select either LOW, HIGH or AUTO fan speed. If "AUTO" is selected (During cooling function),”HIGH” or "MEDIUM" or “LOW" will be selected automatically according to the difference between setting temperature and ambient temperature.
- Page 10 10. HUMIDIFICATION 1. The unit will stop automatically after four hours operating in this mode. Please put some water (Approx 0.8L) into the filler and turn it on again. 2. The unit will stop humidifying if ambient humidity is equal to the pre-set humidity. Otherwise it will work as the humidifying procedure1.
- Page 11 REMOTE CONTROL FUNCTION On/Off switch Function “MODE” selector Hourly programming Automatic fan speed High fan speed Low fan speed Night operation selector Temperature selector Swing...
- Page 12 NOTICE This unit can evaporate the condensation and distribute through the exhaust hose automatically. When the unit is in the cooling function, it does not need the drain pipe installed. Please make sure that the rubber cap① is locked on drain hole, when the unit is running.
- Page 13 MAINTENANCE PLEASE DISCONNECT THE POWER CORD BEFORE CLEANING. AIR FILTER 1. The air filter located on both sides of the unit can be removed simply by pulling the frame out. 2. Wash the filter with cool water (cooler than 40℃) every two weeks, and put filter back after it air-dried naturally.
- Page 14 PLACE FOR USE (1) Because the machine distributes hot air, please don’t place or operate in a narrow place. (2) In case of dangerous leak, don’t work the machine in a humid place. (3) Don’t place the machine in a sunlit corner otherwise the unit might shut down due to the overheat and the color of the machine may soon fade out.
-
Page 15: Air Outlet
EXHAUST HOSE INSTALL 1. Take out the joint tube from the exhaust pipe(see picture ①) and fix a part and b part together. 2. Please take out the hot air outlet joint and put the right side filter into the hot air inlet. 1. -
Page 16: Water Tank
TROUBLE SHOOTING Problem Cause Trouble shooting Electrical short on both Contact an electrician for repair temperature sensor and PCB(environment) Electrical short of Contact an electrician for repair temperature sensor copper tube and PCB wiring(coil) Indicates water tank full or User needs to pull out the rubber stopper possibly the incorrect which is located at the bottom of the unit, to wiring of plug... - Page 17 SPECIFICATION Model No. MDM-3018 Power Source 220-240V~50Hz Rated Power (EN60335) Cooling 590W Heating 700W PTC Heater Power 600W Cooling Capacity 1100W Heating Capacity 600W Moisture Removed 30 liters/day Humidifying capacity 0.2L/H Refrigerant R410A Water Tank Capacity 2.6L Dimensions (mm) 375Wx280Dx505H...
- Page 18 Please help us to conserve the environment we live in! DECLARATION OF CONFORMITY Herewith, Amiridis-Savvidis S.A. states that model MDM-3018, complies with the requirements of below directives: EMC-Directive: 04 / 108 / EC...
Need help?
Do you have a question about the MDM-3018 and is the answer not in the manual?
Questions and answers