Page 1 Multi-Section Outdoor LED Scoreboards Installation, Maintenance, and Specifications Manual ED12562 ® All Sport is a registered trademark of Daktronics, Inc. ® National Electrical Code is a registered trademark of NFPA International. Scoreboard Models BA-1518-11 FB-1424-11 FB-1630-11 FB-2001-11 SO-1424-11 BA-1524-11 FB-1430-11...
Page 3: Table Of Contents
Table of Contents Section 1: Introduction....................1-1 How To Use This Manual ..................1-1 Daktronics Nomenclature...................1-2 Manual Overview.......................1-3 Product Overview.......................1-3 Model Names ......................1-4 Product Safety Approval ....................1-4 Section 2: Model Identification .................. 2-1 Section 3: Specifications.................... 3-1 Multi-Section Scoreboards..................3-2 Section 4: Component Locations ................
Page 4 Power-On Self-Test ....................8-5 Lightning Protection ....................8-5 Troubleshooting......................8-5 Replacement Parts ..................... 8-7 8.10 Daktronics Exchange and Repair and Return Programs..........8-7 Section 9: Team Name Message Center Maintenance ..........9-1 Team Name Message Center System Overview............9-1 Maintenance and Troubleshooting Overview............9-1 Signal Summary......................
Page 5: Introduction
Appendix. Listed below are a number of drawing types commonly used by Daktronics, along with the information that each is likely to provide. System Riser Diagrams: overall system layout from control room to display, power, and phase requirements.
Page 6: Daktronics Nomenclature
This manual, for example, would be referred to as ED13313. The serial and model numbers of a Daktronics scoreboard can be found on the ID label on the display. The label will be similar to the one shown in Figure 2.
Page 7: Manual Overview
1.4 Product Overview Daktronics outdoor LED scoreboards are part of a family of scoring and timing displays designed to offer easy installation, readability and reliability. Microprocessor control assures consistent operation and accuracy.
Page 8: Model Names
120 V AC power requirement. 1.6 Product Safety Approval Daktronics outdoor scoreboards and timing displays are ETL listed, tested to CSA standards and CE labeled for outdoor use. Contact Daktronics with any questions regarding testing procedures Introduction...
Page 9: Model Identification
Section 2: Model Identification Use the following drawings to determine the scoreboard model number. The drawings are listed here in alphabetical order by scoreboard model line, and they are inserted in the Appendix in alphanumeric order. Individual scoreboard drawings are also grouped in the Appendix. Reference Drawing: Multi-Section Baseball Scoreboards ..........
Page 11: Specifications
Section 3: Specifications The chart on the following pages shows all of the mechanical specifications, circuit specifications and maximum power requirements for each model in this manual. Models are listed in alphanumeric order. Specifications...
Page 12: Multi-Section Scoreboards
3.1 Multi-Section Scoreboards Note: Signal wires must be a minimum of 22 gauge with shield. Daktronics recommends using W-1234. (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and...
Page 13 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Runs, Hits, Errors BA-1524-11 2 Total H9'-0", W16'-0", D6" 480 lb 340 W 120 V AC 2.8 A...
Page 14 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Innings, Runs, Hits, BA-3718-11 4 Total H7'-0", W28'-0", D6" 720 lb 950 W 120 V AC 7.8 A...
Page 15 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) FB-1424-11 2 Total H8'-0", W18'-0", D6" 400 lb ¡ Indicators (2438 mm, 5486 mm, 182 kg 8"...
Page 16 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Clock FB-1530-11 2 Total H8'-0", W25'-0", D6" 580 lb 430 W 120 V AC 3.6 A (2438 mm, 7620 mm,...
Page 17 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Clock FB-1630-11 2 Total H8'-0", W25'-0", D6" 620 lb 695 W 120 V AC 5.8 A w/TNMC...
Page 18 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Clock FB-1730-11 2 Total H8'-0", W25'-0", D6" 620 lb 400 W 120 V AC 3.3 A (2438 mm, 7620 mm,...
Page 19 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Clock FB-1830-11 2 Total H8'-0", W25'-0", D6" 760 lb 730 W 120 V AC 6.1 A w/TNMC...
Page 20 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Clock FB-2001-11 2 Total H10'-0", W32'-0", D6" 940 lb 455 W 120 V AC 3.8 A (3048 mm, 9754 mm,...
Page 21 ((Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Clock, Score, MS-2009-11 2 Total H10'-0", W25'-0", D6" 480 lb 360 W 120 V AC 4.7 A (3048 mm, 6096 mm,...
Page 22 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Indicators SO-1624-11 2 Total H8'-0", W18'-0", D6" 520 lb 685 W 120 V AC 5.7 A w/TNMC...
Page 23 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Clock SO-1830L-11 2 Total H8'-0", W32'-0", D6" 720 lb 440 W 120 V AC 3.7 A (2438 mm, 9754 mm,...
Page 24 (Continued from previous page) Model Number Dimensions Weight Digit Size Maximum Power Amps Per Driver (Height, Width, Uncrated Wattage Line Number and Sections Depth) (Crated) (Single Address Phase) ¡ Clock SO-1930-11 2 Total H8'-0", W25'-0", D6" 950 lb 770 W 120 V AC 6.4 A w/TNMC...
Page 25: Component Locations
Appendix in alphanumeric order by drawing number. Reference Drawings: Component Locations, BA-1518-11........... Drawing A-141077 Component Locations, BA-1518-11 w/TNMC ........Drawing A-144637 Component Locations, BA-1524-11........... Drawing A-141745 Component Locations, BA-2007-11 w/LED TNMC ......Drawing A-147199 Component Locations, BA-3718-11........... Drawing A-141749 Component Locations, BA-3718-11 w/TNMC ........
Page 27: Schematics
Section 5: Schematics Reference Drawings: Schematic; 1 Driver ................Drawing A-141799 Schematic; 1 Driver w/TNMC ............Drawing A-141806 Schematic; 2 Drivers ................. Drawing A-141807 Schematic; 2 Drivers w/TNMC............Drawing A-141808 Schematic; 3 Drivers ................. Drawing A-142358 Schematic; 3 Drivers w/TNMC............Drawing B-142360 Schematic;...
Page 28 (Continued from the previous page) Models Schematic Name Drawing FB-1830 Schematic; 2 Drivers A-141807 FB-1830 w/TNMC Schematic; 2 Drivers w/TNMC A-141808 FB-1830L Schematic; 2 Drivers A-141807 FB-1830L w/TNMC Schematic; 2 Drivers w/TNMC A-141808 FB-2001 Schematic; 2 Drivers A-141807 FB-2002 Schematic; 2 Drivers A-141807 FB-2003 Schematic;...
Page 29: Mechanical Installation
6.1 Scoreboard Protective Devices Note: Some owners install devices to protect the display from projectiles. Scoreboard protection devices not provided by Daktronics must be approved by Daktronics prior to installation. Failure to follow this approval procedure will void the scoreboard warranty.
Page 30 Models Without Team Name Reference Drawings Message Center FB-1424-11, FB-1524-11, FB-1624- Beam & Footing Recommendations, A-44514 11, SO-1424-11, SO-1624-11 FB-XX24 Beam Spacings, Football/Track/Soccer A-70089 Structure, Football A-44556 FB-2001, FB-2002-11, FB-2003-11 Beam Spacings, Football/Track/Soccer A-70089 Structure, Football A-44556 Beam and Footing Recommendations, A-160931 FB-200X Installation Specifications, FB-2002 &...
Page 31 Be sure that your installation complies with local building codes and is suitable for your particular soil and wind conditions. Daktronics assumes no liability for installations derived from the information provided in this manual or installations designed and installed by others. Mechanical Installation...
Page 32: Lifting The Scoreboard
The eyebolts are located along the top of the cabinet for each scoreboard or scoreboard section. Daktronics strongly recommends using a spreader bar, or lifting bar, to lift the display. Using a spreader bar ensures that the force on the lifting straps or eyebolts is straight up, minimizing lifting stress.
Page 33: Scoreboard Mounting
In typical multi-section installations, the lower scoreboard section is installed first and secured to the support beams, and the upper section is then placed atop or above the lower section and attached to the beams. There may be cables extending from the top of the lower section. Guide these cables into the hole in the bottom of the upper section for later connection.
Page 34: Ad Panel Mounting
6.5 Ad Panel Mounting Reference Drawing: Ad Panel Mounting ................Drawing A-52187 Drawing A-52187 shows the mounting of advertising or identification panels. Mount the ad panel or ad panels in the following manner: 1. Use the mounting channel to determine which hole combination to use. Be sure to keep the bolts as close to the beam as possible.
Page 35: Electrical Installation
Refer to the chart in Section 3 to determine circuit specifications and maximum power requirements for the models described in this manual. Daktronics outdoor LED scoreboards have been designed for easy access to components, and the power and control signal hookup has been simplified. Front panels are removable to allow access to the digits, cabling, and other electronic components.
Page 36: Grounding
Grounding Displays MUST be grounded according to the provisions outlined in Article 250 of the National Electrical Code and according to the specifications in this manual. Daktronics recommends a resistance-to-ground of 10 ohms or less. The electrical contractor who is performing the electrical installation can verify ground resistance.
Page 37: Power And Signal Connection
Installation with Only a Neutral Conductor Provided Installations where no grounding conductor is provided must comply with Article 250-32 of the National Electrical Code. If the installation in question meets all of the requirements of Article 250-32, the following guidelines must be observed: Connect the grounding electrode cable at the local disconnect, never at the...
Page 38: Interconnect Panel Connections
Interconnect Panel Connections Reference Drawings: Interconnect Panel Digit Designation ......Drawing A-174754 All multi-section football and soccer scoreboards use an interconnect panel as a connection between the digits of the top section and their corresponding driver. Because both drivers are located in the bottom section, only the top section digits use an interconnect panel.
Page 39: Scoreboard Maintenance And Troubleshooting
8.1 Cabinet Specifications Cabinets for the Daktronics outdoor LED scoreboards are constructed of heavy-gauge aluminum. Exact dimensions and weights for each model are listed in the chart in Section 3. Removable panels for digits and indicators and for component access are detailed in each model's Component Locations drawing, listed in Section 4.
Page 40: Replacing A Digit
Reference Drawing: Digit; 24" 7-Seg LED..............Drawing A-155644 Some larger Daktronics digits are comprised of individual segments. The digit segment circuit board, the platform for the LEDs, is mounted to the back of the digit panel. Do not attempt to remove individual LEDs.
Page 41: Replacing A Breakout Board
Note: This is a keyed connector B it will 5. Reconnect the power/signal connector. attach in one way only. Do not attempt to force the connection! 6. Close and secure the digit panel and test the scoreboard. Replacing a Breakout Board The digit breakout board, the central signal/power termination for the segments, is mounted to the back of the digit panel.
Page 42: Schematic
8.3 Schematic Refer to Section 5 for a complete listing of the schematics for the Daktronics multi-section outdoor LED scoreboards. The drawings diagram the power and signal inputs and all wiring for each scoreboard model. 8.4 LED Drivers Reference Drawings: 16 Column LED Driver II Specifications..........
Page 43: Power-On Self-Test
8.8 Troubleshooting Daktronics scoreboards require little maintenance. However, from time to time, a display may malfunction, and certain display components will have to be repaired or replaced. The following table provides a list of problems common to most LED displays and specifies corrective actions:...
Page 44 Your scoreboard service may advise you to call Daktronics directly, or your facility may not have an area or regional service provider. In those instances, feel free to call the Daktronics Help Desk at 877-605-1115.
Page 45: Replacement Parts
8.9 Replacement Parts The following Daktronics parts list includes components used by all of the LED outdoor timers. Some part numbers are listed on the final assembly engineering drawings in the Appendix. Description Location Part No. LED driver, 16 column...
Page 46 If you do not ship the defective equipment Daktronics within 30 working days from the invoice date, Daktronics assumes you are purchasing the replacement part outright (with no exchange), and you will be invoiced for it.
Page 47 This is how to reach us: Mail: Customer Service, Daktronics Inc. PO Box 5128 331 32nd Ave Brookings SD 57006 Phone: Daktronics Help Desk: 877-605-1115 (toll free) or 605-697-4036 Fax: 605-697-4444 E-mail: helpdesk@daktronics.com Maintenance and Troubleshooting...
Page 49: Team Name Message Center Maintenance
Standard Daktronics outdoor LED scoreboards are typically front-accessible, but some models may be ordered with rear service access. Because of that, Daktronics team name message centers have been designed so that they may be accessed from both the front and rear for easy maintenance and repair of internal components.
Page 50: Signal Summary
Replacement Parts Lists: lists the part description and part number of display components that could possibly need replacing during the life of this display. Daktronics Exchange and Repair and Return Programs: explains the Daktronics component return policy. 9.3 Signal Summary Reference Drawing: Control Layout;...
Page 51: Tnmc Current Loop Interface Card
The following subsections address servicing of the following display components: TNMC Interface Card TNMC Controller Modules and Drivers Power Supplies The subsections also address any diagnostic LEDs, fuses and signal/power connectors found on the unit. On Drawings A-143808, A-144323, A-145045, the TNMC components are denoted in the table on the following page.
Page 52: Tnmc Controller
TNMC Controller The controller, located on the rear-access panel, receives signal from the CLI and sends data to the modules. Refer to Drawing A-145045 for the position of the controller board. Figure 7, below, illustrates a typical controller. Figure 7: Controller Component Layout DIP switches are located on the controller's MDC (see Figure 7).
Page 53 Switch Number Address Test Mode … … … … … … … … … Four diagnostic LEDs are located on the controller. Two other LEDs note when the MDC is receiving signal information. The following table explains what each LED represents. Color Function Operation...
Page 54: Modules And Drivers
quarter-turn. Use a " nut driver. Turn the top latch clockwise and the bottom latch counterclockwise. Carefully remove the module and detach the ribbon cables. It may be helpful to label the cables to know which cable goes to which connector when reattaching.
Page 55: Power Supplies
When installing a module, reverse the previous steps, taking note of the following conditions: Weatherstripping on the back edge of the module must be intact and in good condition if it is to prevent water from seeping into the display. Module latches must be fully engaged to create a watertight seal around the edge of the module.
Page 56: Tnmc Display Maintenance
9.6 TNMC Display Maintenance Complete a yearly inspection to maintain safe and dependable display operation. This inspection should address the following issues: Loose Hardware Verify that fasteners, such as bolts and rivets, have not come loose. Check and tighten or replace fasteners as required.
Page 57: Initialization Information At Startup
Symptom/Condition Possible Cause/Remedy § Entire display fails to work. Check for proper line voltage into the power termination panel. § Check/replace the ribbon cable from the controller to the modules. § Check the voltage settings on the power supplies. § Check/replace the signal cable to the controller.
Page 58: Tnmc Exchange And Repair And Return Programs
To prevent theft Daktronics recommends purchasing a lockable cabinet to store manuals and replacement and spare parts. 9.10 TNMC Exchange and Repair and Return Programs Refer to Section 8.10 for information on the Daktronics Exchange and Repair and Return programs. 9-10 TNMC Maintenance...
Page 59: Scoreboard Options
This section lists information on optional equipment for the outdoor LED scoreboards. 10.1 Football Scoreboard Accessories The following options are available for the Daktronics football scoreboard. They make the scoreboard more adaptable to scoring and timing needs: Caption kits for additional sports Trumpet horn for football and soccer 10.2 Captions for Other Sports...
Page 60: Trumpet Horn
An optional caption changer is available for installing and removing panels from the ground. Each caption panel is punched with keyholes. Screw heads on the crossbar of the caption changer fit into the keyholes. The caption changer pole consists of three sections, with a ring tightener to adjust for length.
Page 61: Dc Trumpet Horn Installation (Externally Mounted)
7. Connect to power the scoreboard. 8. Connect the control console to the scoreboard. 9. Test the horn by pressing the key labeled HORN on the control console. DC Trumpet Horn Installation (Externally Mounted) Caution: Disconnect scoreboard power before installing the horn! Refer to Drawings A-128938 and A-162102 for complete installation information.
Page 62: Radio Control
10.4 Radio Control Radio control is an option with all Daktronics outdoor LED scoreboards, the system providing scoreboard control via a 2.4 GHz, extra-high frequency FM signal. The radio transmitter and receiver are not standard equipment. This setup requires a control console such as the All Sport, equipped with radio output.
Page 63: Appendix A: Reference Drawings
16 Column LED Driver II Specifications ............ Drawing A-134371 Digit Assembly (15”).................. Drawing A-135538 Digit Assembly (18 and 24”) ..............Drawing A-135662 Component Locations, BA-1518-11 ............Drawing A-141077 Component Locations, BA-1524-11 ............Drawing A-141745 Component Locations, BA-3718-11 ............Drawing A-141749 Component Locations, BA-3724-11 ............
Page 64 F. Assy; 832 LED TNMC................Drawing A-143808 F. Assy; 848 LED TNMC................Drawing A-144323 Installation Specifications, MS-2009 ............Drawing A-144415 Component Locations, BA-1518-11 w/TNMC..........Drawing A-144637 Component Locations, BA-3718-11 w/TNMC..........Drawing A-144659 Component Locations, BA-3724-11 w/TNMC..........Drawing A-144678 Component Layout; 832/848 LED TNMC..........Drawing A-145045 Component Locations, FB-1830-11 ............
Page 155 Appendix B: Eyebolts Eyebolts ........................ED7244 Eyebolts...
Page 157 Eyebolts Almost every display that leaves Daktronics is equipped with eyebolts for lifting the display. There are two standard sizes of eyebolts: ½″ and A″. Load Increase Factor: The load increases as the lift angle (θ) decreases. The allowable load on the eyebolts also decreases with the lift angle due the bending stress on the eyebolts.
Page 158 F. Eyebolts should never be painted or otherwise coated when used for lifting. Such coatings may cover potential flaws in the eyebolt. G. To attain the safe working loads listed for regular eyebolts, 90% of the thread length must be engaged. Copyright 1996-2001 ED-7244 Daktronics, Inc. Rev. 4 – 14 March 2001...

Daktronics BA-1518-11 Installation, Maintenance, And Specifications Manual

Quick Links

Troubleshooting

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Daktronics BA-1518-11

Summary of Contents for Daktronics BA-1518-11

This manual is also suitable for:

Table of Contents