Advertisement
Quick Links
PipeFeeder HighSpeed
Article number: 10107
Date: August 2014
Version 1.1 - Translation of original instructions for use
According to Annex 1 Chapter 1.7.4 Machine guideline 2006/42/EG
Benefit of carrousel
24VAC & 12-24VDC
Installation and operating instruction
Hanskamp AgroTech BV
Zelhem, The Netherlands
www.hanskampagrotech.nl
EN
Advertisement
Related Manuals for Hanskamp PipeFeeder HighSpeed
Summary of Contents for Hanskamp PipeFeeder HighSpeed
- Page 1 PipeFeeder HighSpeed Benefit of carrousel 24VAC & 12-24VDC Installation and operating instruction Article number: 10107 Date: August 2014 Hanskamp AgroTech BV Version 1.1 - Translation of original instructions for use Zelhem, The Netherlands According to Annex 1 Chapter 1.7.4 Machine guideline 2006/42/EG...
- Page 2 All information in this manual has been compiled with care. Hanskamp AgroTech shall not be liable for errors or faults in this manual. The recommendations are meant to serve as guidelines.
- Page 3 The information in this manual is for farmers and technicians. Dairy farmers use the information to test and adjust the PipeFeeder or to list over- views. Technicians use the information to install and setup the PipeFeeder. 3 - 19 Hanskamp AgroTech B.V. (the Netherlands) www.hanskampagrotech.nl/en...
- Page 4 Only use approved spare parts, and make sure they are only installed by authori- zed technicians. The PipeFeeder HighSpeed should be shielded, so that te dosing system is un- reachable. This separation should meet European standards and guidelines. Wit- hout this separation the PipeFeeder HighSpeed dooesn’t meet the safety require- ments of Hanskamp AgroTech.
- Page 5 Review safety related items with all operators frequently (annually). The PipeFeeder HighSpeed should be shielded, so that te dosing system is un- reachable. This separation should meet European standards and guidelines. Wit- hout this separation the PipeFeeder HighSpeed dooesn’t meet the safety require- ments of Hanskamp AgroTech.
- Page 6 General safety messages appear in this safety messages section. Specific safety messages are in applicable parts of this manual when potential hazards may occur if the instructions or procedures are not followed. 6 - 19 Hanskamp AgroTech B.V. (the Netherlands) www.hanskampagrotech.nl/en...
- Page 7 Please read the whole installation instructions and keep the safety instructions in mind. If the PipeFeeder is controlled by an MotorController from Hanskamp AgroTech, see also installation instructions Art. No. 1841. This can be requested from the manufacturer. If the PipeFeeder is not controlled by the MotorController, always consult the manual for the relevant control unit.
- Page 8 Do not use any solvents or abrasives that could damage the safety stickers. Replace missing or illegible safety stickers. Safety stickers are available by Hanskamp AgroTech. Always use the article numbers in your correspondence. 1755 Warning sticker: The PipeFeeder can start automa- tically.
- Page 9 The PipeFeeder is designed to hang directly above the feed trough so that the fall height remains low so noise and dust are reduced. Also the PipeFeeder HighSpeed can be mounted, above a hop- per.
- Page 10 MotorController, then several PipeFeeder dosing units can be connected to a single feeding line. Please note the maximum permissible current, which is stated on the power supply (art.nr. 2812 or 2813 PowerUnit), won’t be ex- ceeded. 10 - 19 Hanskamp AgroTech B.V. (the Netherlands) www.hanskampagrotech.nl/en...
- Page 11 End assembly 1. After the assembly the PipeFeeder HighSpeed has to be covered by shields. Because all the different situations, the Installer has to take care of this. 2. When the covers aren’t installed, the machine isn’t safe and doesn’t meet the issued declaration of conformity.
- Page 12 No part of this publication may be reproduced or made public without prior permission in writing from Hanskamp AgroTech BV. Although this publication was put together with the utmost care, Hanskamp AgroTech is not liable for any damage that might arise due to errors or gaps in this publication.
- Page 13 The Netherlands, Zelhem 4-10-2013 H.J. Hanskamp 13 - 19 Hanskamp AgroTech B.V. (the Netherlands) www.hanskampagrotech.nl/en...
- Page 14 The rotor can be rotated by hand proper amount. when it is empty. PipeFeeder doesn’t distribute Calibration is incorrect. Calibrate the controller. (see page 11, step the proper amount. 14 - 19 Hanskamp AgroTech B.V. (the Netherlands) www.hanskampagrotech.nl/en...
- Page 15 PipeFeeder HighSpeed t.b.v carrousel 24VAC & 12-24VDC Annexes Hanskamp AgroTech can supply the following types of dosing units: 29330 Art. Nr.: Lengte: Productgroep: Kleur: Motor: 0 = HighSpeed extra kort L= 724.5 mm 1 = HighSpeed kort L= 1044.5 mm...
- Page 16 Loose components: It is possible to reorder loose components from your supplier for maintenance, or for any other reason. Please use the item numbers shown below on the drawing. 27000 PipeFeeder HighSpeed DC 16 - 19 Hanskamp AgroTech B.V. (the Netherlands)
- Page 17 1934 Connector DC motor 1937 Sticker CE PipeFeeder with serial number 1942 Assembly bottom plate DC & HighSpeed 1947 Membrane grommet thermoplastic elastomer 1951 Blind rivet DIN all stainless steel a2 17 - 19 Hanskamp AgroTech B.V. (the Netherlands) www.hanskampagrotech.nl/en...
- Page 18 PipeFeeder HighSpeed t.b.v carrousel 24VAC & 12-24VDC Installation dimensions: Visit us on: 18 - 19 Hanskamp AgroTech B.V. (the Netherlands) www.hanskampagrotech.nl/en...
- Page 19 PipeFeeder HighSpeed t.b.v carrousel 24VAC & 12-24VDC Hanskamp AgroTech B.V. Arendsenweg 7 7021 PC Zelhem The Netherlands Tel: +31 (0)314 - 393 797 Fax: +31 (0)314 - 393 826 www.hanskampagrotech.nl 19 - 19 Hanskamp AgroTech B.V. (the Netherlands) www.hanskampagrotech.nl/en...
Need help?
Do you have a question about the PipeFeeder HighSpeed and is the answer not in the manual?
Questions and answers