Field Of Use; Handling And Unpacking; General Warnings; Unpacking - Orved LST Operating And Service Manual

EN

HANDLING AND UNPACKING

3.2

FIELD OF USE

ORVED thermo-sealing machines are designed and built to package products inside specially made trays.
The machine must not be used in other ways or for purposes other than that indicated by the manufacturer in this Manual. Conformant use of the
machine also involves abiding by and understanding the warnings and notices in this instruction Manual, as well as prompt checking, maintenance
and cleaning operations.
DANGER! The manufacturer declines all responsibility for damage to persons, animals and objects deriving from non
conforming use of the machine.
4. HANDLING AND UNPACKING
4.1

GENERAL WARNINGS

Pay attention to metal tips, nails, rivets, sharp edges and everything else that could be a potential source of risk on the packing. On receiving the
machine, the Client must check to make sure it is intact, and inform the haulage contractor, or the transport personnel immediately of problems, missing
parts or evident damage; this must be done before proceeding with other handling or unpacking operations.
WARNING: Damage, if any, on the packing may mean possible damage to the machine
or its parts; in case of doubt regarding the actual condition of the machine following
transport, contact the manufacturer for information, before carrying out any other operation.
WARNING: The packed machine must be kept in a safe,
dry place, covered and protected from environmental
agents. The storage area temperature must be between 5°C
and 40°C and the relative humidity not more than 80%.
4.2

UNPACKING

After removing the packing, check to make sure the machine is intact;
do not use it if in doubt and contact the dealer immediately. The packaging
materials (plastic bags, etc.), must be kept out of the reach of children,
and not dumped in the environment. Keep the packaging materials for
future handling or storage of the machine.
WARNING: Disposal of the packing materials must be done
in accordance with the Directives on the matter applicable
in the country in which the machine is installed.
4.3

HANDLING AND STORAGE

- In case of transport within the installation area, the machine
must always be kept in the horizontal position.
The tray-holding shelves in the Profi 2 models must be held in
place by adhesive tape.
- In case of storage:
The machine must be stored in a safe place, suitable for the
purpose, dry, ventilated, covered, and sheltered from atmospheric
agents. The storage area temperature must be between 5°C and
40°C with a relative humidity value not higher than 80%. The
installation area must be free of water and water vapour.
5.

INSTALLATION

5.1

APPLIANCE DESCRIPTION

Orved thermo-sealing machines can package products in trays
of various sizes and capacity and made of a variety of materials.
The protective film is sealed around the edge of the tray by the
pressure of a sealing head heated to a suitable temperature.
The machines are composed of the following basic parts:
- A body (A) in painted or stainless steel.
- A top section attached to the casing by a gas spring (B),
containing the sealing head (C).
The top is equipped with a sturdy handle for lowering the sealing
EN head and pressing it onto the tray.
- A sledge tray holding system (D) (mod. LST and PROFI-1) or shelf (E) (PROFI-2 and PROFI-3 )
- A digital thermostat (F) (PROFI-1, PROFI-2 and PROFI-3) or temperature regulation potentiometer (G) (mod. LST).
- Two reel support rollers (H).
- An electrical system comprising wiring , electronic board (mod. LST), heating element located on the
sealing head and a temperature sensor.
The adaptable optional extras are, exclusively for the PROFI 2 and PROFI-3 models:
- Personalized tray holders: (Rif. E).
Within the limits of the dimensions indicated in the table, it is possible to create special holders on
request.
- Special rollers: (exclusively for the PROFI-2 model)
Allows the machine to be adapted to accommodate film reels of a width of up to 230 mm.
Operation and maintenance manual / Ed. 06 - 2007
THERMO-SEALING MACHINE FOR TRAYS
LST
C
•
B
D
•
•
•
•
•
•
•
A
G
PROFI 1
D
•
F
•
FUSES
22
FUSES
•
E
•
H
PROFI 2
E
•
F
•
FUSES
PROFI 3
E
•
F
•
FUSES
REV. 02 - Cod.: 1500161
FUSES