Fisher & Paykel WM1490F Installation Instructions Manual
Hide thumbs
Also See for WM1490F:
- Installation manual/user manual (56 pages) ,
- Installation instructions manual (56 pages)
Table of Contents
Advertisement
Quick Links
Installation Instructions
Accessories
Please check you received the following accessories with your Fisher & Paykel washer.
You will find them inside the drum or attached to the packaging.
• 2 x Inlet hoses
• 1 x Drain hose guide
• 1 x Installation instructions and user guide
• 1 x Spanner
• 1 x Installation leaflet (attached to the top of the washer)
• 1 x Inlet valve cap
• 1 x Hose clamp
Unpacking
To ensure the best performance from your new washer please follow the instructions below
Removing The Packaging
1. Remove the outer packaging (including the polystyrene packer and plastic wrapping). All packaging must be
removed prior to use. Ensure these materials are kept out of reach of children. Note: a small amount of water
may be seen inside the packaging and inside the washer. This is the result of factory testing and is normal.
2. Tilt the machine backwards and 'walk' it off the base one foot at a time. Not doing so may cause damage to
your floor and washer.
3. Remove all packaging and accessories from inside the drum.
https://producthelp.fisherpaykel.com/eu/Wash/Front_Loaders/WashSmart/WM1480P1/User_Guide_WM1480P1/03_Installatio...
Updated: Wed, 12 Feb 2020 12:46:42 GMT
Powered by
1
Advertisement
Table of Contents
Related Manuals for Fisher & Paykel WM1490F
Summary of Contents for Fisher & Paykel WM1490F
- Page 1 Installation Instructions Accessories Please check you received the following accessories with your Fisher & Paykel washer. You will find them inside the drum or attached to the packaging. • 2 x Inlet hoses • 1 x Drain hose guide • 1 x Installation instructions and user guide •...
-
Page 2: Removing The Transit Bolts
Removing The Transit Bolts The clothes washer is fitted with 4 transit bolts at the rear to avoid damage during transportation. The 4 transit bolts MUST be removed prior to operation of the machine. Failure to remove these will result in damage to the machine. To Remove The Bolts: 1. - Page 3 TOP VIEW FRONT VIEW WM1490F, WM1490P WM1480P, WM1280J Product Dimensions A. Overall height of product B. Overall width of product C. Overall depth of product (excluding dial and door when closed) D. Depth of door open 1065 1010 E. Minimum door clearance to adjacent wall Standpipe height min.
- Page 4 WM1490F, WM1490P WM1480P, WM1280J Product Dimensions The exact height of your washer is dependent on how far the feet are extended from the base of the machine. The space where you install your washer needs to be at least 40mm wider and 20mm deeper than its dimensions.
-
Page 5: Levelling The Machine
Levelling The Machine It is IMPORTANT to level the machine to ensure good spin performance, and to minimise noise, vibrations and wear and tear on the washer. 1. Before positioning the machine in its final position, check that the machine is level, front to back and side to side. 2. -
Page 6: Inlet Hoses
Inlet Hoses New hose sets provided with the washer should be used to connect the washer to the water mains. Old hose sets should not be re-used. We recommend the inlet hoses are changed every 5 years. Failure to do so result in a flood damage... - Page 7 RMC TVA 75HFS Adjustable between 35°C – 55°C RMC TVA 50HP For instantaneous gas hot water supply Water Supply Requirements: • Inlet water pressure: Maximum 1MPa (150psi), Minimum 30kPa (4.5psi) • Inlet water flow rate: Minimum 6 litres/minute Cold Supply Only: If you only have a cold water supply, the inlet valve cap (blanking cap) which came with your washer must be connected to the hot inlet valve.
- Page 8 Drain Hose Placement in a Stand Pipe or Tub 1. To guide the drain hose over the tub or standpipe the hose guide must be fitted to the drain hose. The height of the standpipe or tub should be between 800 – 1200mm. 2.
-
Page 9: Attaching Drain Hose To Spigot
Attaching Drain Hose To Spigot 1. Guide drain hose through hose guide 2. Secure hose guide to back wall of cupboard using a screw. The height of the drain hose should be between 500 – 800mm from ground level. 3. Attach drain hose to spigot and secure using a hose clamp ensuring the blanking insert is cleared from spigot. -
Page 10: Completing The Installation
• If you are using an extension cord or a portable electrical outlet device (eg multisocket outlet box), ensure that it is positioned so that it does not come into contact with water or moisture. FAILURE TO DO SO MAY RESULT IN DEATH OR ELECTRICAL SHOCK. •... - Page 11 • The washer will beep and display any faults on the screen if there are any problems. Refer to ‘Before you call for Service’ section at the back of this book. 4. Wait until you see water in the bottom of the drum. 5.