Removal Instructions - Chicco OASYS 1 EVO ISOFIX Manual

6. Insert the two ISOFIX connectors into the
corresponding ISOFIX locking devices, located
on the cars seat, between the backrest and
the seat (diag. 11). WARNING! Pull the child
car seat towards you to ensure it has been
installed correctly and then check that the
two indicators (W) are green.
7. Push the child car seat firmly against the
backrest of the car seat (Diag. 12) to ensure
maximum adherence.
How to fit the top tether
The installation of the child car seat is
complete only by fitting the Top Tether.
WARNING! Pease refer to the instructions
booklet of the vehicle to identify the locking
point of the Top Tether of the child car seat.
This locking point is indicated by a special
label (Diag. 13), and it may be located in the
positions indicated in diagrams 14a – 14b –
14c – 14d.
WARNING! Check that the Top Tether is locked
with the correct locking device. Do not
mistake the locking device of the Top Tether
with the ring provided for securing luggage
(diag. 15).
WARNING! Insert the Top Tether between the
top part of the backrest of the car seat and the
headrest. Never insert the Top Tether above
the car headrest (diag. 16).
8. After identifying the locking point, connect
the hook (DD) of the Top Tether to it (diag. 17.
9. Adjust the length of the Top Tether belt,
pulling the strap firmly to tension it correctly
(diag. 18). The belt is tensioned correctly when
the indicator located on the strap is green
(diag. 19).
10. Roll up the excess strap and fasten it with
the specific Velcro strap provided (diag. 20).

REMOVAL INSTRUCTIONS

WARNING! Remove the child from the child
car seat before commencing.
1. Loosen the Top Tether by pressing the
appropriate button BB (diag. 21), then
disconnect the hook DD.
2. Roll up the Top Tether strap and fasten with
the specific Velcro strap provided (diag. 20).
3. Pull the ISOFIX system unlocking handle
outwards and, whilst keeping hold of it (diag.
22) lift the child car seat away from the vehicle
seat until it disconnects from the ISOFIX
system (diag. 23).
4. Push the two red buttons (V) inwards
and release the connectors from the
corresponding ISOFIX locking devices, located
on the car seat (diag. 24).
5. Remove the two previously stored caps
(U) from the compartment between the
seat and the backrest (Diag. 25) and reinsert
them in the related ISOFIX connectors, paying
attention that the two ends are facing inside
(Diag. 26).
6. Push the ISOFIX system inside the base of
the child car seat, inserting it completely into
the base.
SEATING THE CHILD IN THE CHILD CAR
SEAT
Before sitting your child in the child car seat, press
the harness adjustment button (D) and, at the
same time, hold the two child car seat harnesses
under the shoulder straps, and pull them in your
direction to slacken them (Diag. 27).
- Unfasten the buckle (F) of the child car seat
harnesses by pressing the red button (Diag.
28), and pull the harnesses in an outward
direction. Now the child can be placed in the
child car seat (diag. 29).
- Position the crotch strap correctly, take the
harnesses, overlap the two buckle straps (diag.
30a - 30b) and push them together firmly
inside the buckle slot, until a "click" is heard
(diag. 31).
HOW TO REMOVE THE CHILD FROM THE
CHILD CAR SEAT
To remove the child from the child car seat,
press the red button on the buckle (F) and
release the restraint harness.
ADJUSTING
HARNESSES
The height of the headrest and restraint
harnesses can be simultaneously adjusted to
6 positions by pressing the button located at
the rear (M).
WARNING! To adjust them correctly, the headrest
21
THE HEADREST AND