Advertisement
Available languages
Available languages
Call receiver RCL07
GB
Model
Cable entry with
cord grip
RCL07-5001E-02
Technical Details
Frequency:
868.3 MHz
Modulation:
FSK
Coding:
Easywave
Power supply:
12-24 V DC
Power consumption:
0.3 W stand by
0.8 W on-load
Max. contact rating:
30 V / 1 A / 30 W
Output:
1 potential-free
relay contact (CO)
Operating Temperature: -20 °C to +60 °C
Degree of Protection:
IP44
Dimensions:
35/80/20 mm
Weight:
24.0 g
Connecting cable:
Ø 5 mm
Scope of Delivery
Call receiver RCL07, operating instructions
Intended Use
The unit may only be operated with safety extra
low voltage (SELV) and may only be used as a ra-
dio control for switching devices with safety extra
low voltage (SELV).
The manufacturer shall not be liable for any da-
mage caused by improper or non-intended use.
Safety Advice
Before using the device, carefully read
through the operating instructions!
Caution! Observe the permissible supply volta-
ge and the max. contact rating!
Have faulty radio controls checked by the
manufacturer!
Do not make any unauthorized alterations or
modifications to the receiver!
Function
The RCL07 Easywave Mini-Receiver can be ope-
rated in a voltage range of 12-24 V DC.
A total of 32 different Easywave radio transmissi-
on codes can be memorized.
Four operating modes are available:
DEAD MAN´S MODE
The relay is triggered as long as the correspon-
ding transmitter button is pressed (max. 36 secs).
ON/OFF
Transmitter button
A or C
B or D
IMPULSE
If a transmitter button is pressed, the correspon-
ding relay is triggered for 1 second.
Start-Up
1. Remove the housing cover.
2. Select the desired operating mode with
Programming
jumper J1. The factory setting is the DEAD
button with LED
MAN`S MODE.
DEAD MAN´S MODE
(Pos. 1+2)
ON/OFF
(Pos. 2+3)
IMPULSE
(Pos. 4+5)
3. Connect the supply voltage and the safety
extra low voltage devices to be switched as
follows:
4. Re-install the housing cover.
5. Transfer the codes of the transmitters to
the receiver (see section "Programming the
transmission codes").
Caution: Make sure there is no inter-ference with
the wireless connection. Do not mount the device
in a distribution box, in metal casings, in direct
proximity to large metal objects, on the floor or
close to it.
Programming the transmission codes
In the "Programming the transmission codes"
mode you can transfer the codes of your trans-
mitter buttons to the receiver.
The selected operating mode is adopted as a re-
sult of the memorizing process and applies to the
transmission code currently memorized.
1. Briefly (< 1.6 sec.) press the programming
button. The LED flashes.
2. Press and hold a transmitter button. If the
code has been memorized, the LED lights up
and then flashes again. Release the transmit-
ter button.
3. Repeat step 2 with the other transmitters.
4. Briefly (< 1.6 sec.) press the programming
button in order to return to the operating
mode.
Function
1st pressing: ON
2nd pressing: OFF
J1
1
J1
1
J1
1
J1
1
Power supply:
12-24V DC:
IN1, IN2
(Polarity is
arbitrary)
Device:
Channel 1
NC, COM, NO
(change over)
Deleting specific transmission codes
In the Delete mode you can delete specific trans-
mission Codes memorized by the receiver.
1. Keep the programming button pressed for
more than 1.6 sec. The LED flashes rapidly.
2. Press the selected transmitter button. If the
code has been deleted, the LED lights up and
then flashes again rapidly.
3. Repeat step 2 with another transmitter or
briefly (< 1.6 sec.) press the programming
button in order to return to the operating
mode.
Deleting all transmission codes (Reset)
In the Reset mode you can delete all codes me-
morized by the receiver.
1. Keep the programming button pressed for
more than 1.6 sec. The LED flashes rapidly.
2. Press the programming button again and
keep it pressed for more than 1.6 sec. If the
memory has been deleted completely, the
LED lights up and then flashes again rapidly.
3. Briefly (< 1.6 sec.) press the programming
button in order to return to the operating
mode.
Disposal
Waste electrical products not be disposed of
with household waste!
Dispose of the waste product via a col-
lection point for electronic scrap or via
your specialist dealer.
Put the packaging material into the
recycling bins for cardboard, paper and
plastics.
Warranty
Within the statutory warranty period we under-
take to rectify free of charge by repair or replace-
ment any product defects arising from material or
production faults.
Any unauthorized tampering with, or modifica-
tions to, the product shall render this warranty
null and void.
Conformity
This product conforms to the basic
requirements of the R&TTE Directive
1999/5/EC.
For use in: EU/CH/FL/IS/N
The Declaration of Conformity can be found on
the Internet at: www.eldat.de.
Service
If, despite correct handling, faults or malfunctions
occur or if the product was damaged, please
contact the company at the address below:
ELDAT GmbH
Im Gewerbepark 14
15711 Zeesen
Germany
Phone: + 49 (0) 33 75 / 90 37-0
Telefax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-mail: info@eldat.de
101805 16.07.2012 D/GB
Advertisement
