Download
Share
Print this page
  1. Manuals
  2. Brands
  3. ASM Manuals
  4. Paint Sprayer
  5. Zip-Spray 2300 Plus 110V
  6. Operation

ASM Zip-Spray 2100 Plus 110V Operation

Electric airless sprayers
Hide thumbs Also See for Zip-Spray 2100 Plus 110V:

Advertisement

Quick Links

Download this manual See also: Product Service Manual, Repair Parts Manual
Operation / 操作 / 작동
Electric Airless Sprayers
电动无气喷涂机
전기식 에어리스 도장기
- For portable spray applications of architectural paints and coatings -
- 구조적 도장 및 코팅에 대한 휴대용 스프레이 분야 -
3300 psi (227 bar, 22.7 MPa) Maximum Working Pressure /
312361
312363 (English)
312364 (French)
312365 (Spanish)
312362
ti10320a
Stand Models:
™
ASM Zip-Spray
2100 Plus 110V: 247482
ASM AllPro Mustang 4700 Plus 110V: 247483
™
ASM Zip-Spray
2100 Plus 240V: 247484
Important Safety Instructions / 重要安全说明 / 중요 안전 정보
Read all warnings and instructions in this manual. Save these instructions.
请阅读本手册的所有警告及说明。妥善保存这些说明。
이 설명서의 모든 경고와 지침을 읽고 , 이러한 지침을 보관해 두십시오 .
English, Chinese, Korean
,
中文 , 한국어
English
- 适用于建筑涂料和涂层的便携喷涂应用 -
最大工作压力
/
최대 허용 압력
Hi-Boy Models:
™
ASM Zip-Spray
2100 Plus 110V: 247485
ASM AllPro Mustang 4700 Plus 110V: 247486
™
ASM Zip-Spray
2100 Plus 240V: 247487
ASM L1900 Plus 110V: 247494
ASM L1900 Plus 240V: 247495
ASM AllPro Mach 5400 Plus (110V): 247532
™
ASM Zip-Spray
2300 Plus (110V): 247531
312392C
ti10305a

Advertisement

loading
Need help?

Need help?

Do you have a question about the Zip-Spray 2100 Plus 110V and is the answer not in the manual?

Questions and answers

Related Manuals for ASM Zip-Spray 2100 Plus 110V

Summary of Contents for ASM Zip-Spray 2100 Plus 110V

  • Page 1 312365 (Spanish) 312362 ti10305a Hi-Boy Models: ti10320a ™ ASM Zip-Spray 2100 Plus 110V: 247485 ASM AllPro Mustang 4700 Plus 110V: 247486 Stand Models: ™ ™ ASM Zip-Spray 2100 Plus 110V: 247482 ASM Zip-Spray 2100 Plus 240V: 247487 ASM AllPro Mustang 4700 Plus 110V: 247483 ASM L1900 Plus 110V: 247494 ™...

  • Page 2: Fire And Explosion Hazard

    Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where appli- cable.

  • Page 3: Personal Protective Equipment

    Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer. • Check equipment daily. Repair or replace worn or damaged parts immediately with genuine ASM replacement parts only. • Do not alter or modify equipment.
  • Page 4 警告 警告 以下为针对本设备的设置、使用、接地、维护及修理的警告。惊叹号标志表示一般性警告，而各种危险标志则表示与特 定的操作过程有关的危险。请返回此处查阅相关的警告。此外，在本手册的其它适当地方还有与特定产品有关的警告。 警告 火灾和爆炸危险 工作区内的溶剂及涂料烟雾等易燃烟雾可能被点燃或爆炸。为避免火灾及爆炸： 仅在通风良好的地方使用此设备。 • 清除所有火源，如引火火焰、烟头、手提电灯及塑胶遮蔽布 （可产生静电火花） 。 • 喷涂机会产生电火花。当喷涂机使用易燃液体或在其附近使用易燃液体或用易燃液体进行冲洗或清洗 • 时，要让喷涂机离开爆炸性蒸气至少 20 英尺 （6 m） 。 保持工作区清洁，无溶剂、碎片、汽油等杂物。 • 存在易燃烟雾时不要插拔电源插头及开关电灯。 • 将工作区内的设备及导电物体接地。请阅读 接地 说明。 • 如果出现静电火花或感到有电击， 要立刻停止操作。在找出并纠正问题之前，不要使用设备。 • 工作区内要始终配备有效的灭火器。 • 电击危险 系统接地不当、设置不正确或使用不当都可导致电击。 进行设备维修之前，要关闭电源并切断电源线的连接。 • 只能使用已接地的电源插座。 • 只能使用三芯加长电线。...
  • Page 5 警告 警告 设备误用危险 误用设备会导致严重的人员伤亡。 不要超过额定值最低的系统部件的最大工作压力或温度额定值。请阅读所有设备手册中的 技术数据。 • 请使用与设备的流体部件相适应的流体或溶剂。请阅读所有设备手册中的 技术数据。 阅读流体及溶 • 剂生产厂家的警告。有关涂料的完整资料，请向涂料分销商或零售商索要材料安全数据表 （MSDS） 。 要每天检查设备。已磨损或损坏的零部件要立刻修理或更换，只能使用 ASM 的原装替换用零部件进 • 行修理或更换。 不要对设备进行改动或修改。 • 只能将设备用于其特定的用途。有关资料请与 ASM 公司的经销商联系。 • 让软管和电缆远离公共区域、尖锐边缘、移动部件及热的表面。 • 不要扭绞或过度弯曲软管或用软管拽拉设备。 • 儿童和动物要远离工作区。 • 要遵照所有适用的安全规定进行。 • 儿童和动物要远离工作区。 • 疲劳时或在吸毒或酗酒之后不得使用此设备。 • 高压铝质部件危险 不要在加压的铝质装置中使用 1,1,1- 三氯乙烷、二氯甲烷、其它卤代烃溶剂或含有这些溶剂的流体。...
  • Page 6 경고 경고 다음은 이 장비의 설치 , 사용 , 접지 , 유지보수 및 수리에 관한 주의 사항입니다 . 느낌표 기호는 일반적인 주 의 사항을 나타내며 위험 기호는 각 절차에 대한 위험을 의미합니다 . 필요할 때 다시 이러한 경고문을 확인하 십시오 . 이 설명서의 해당 부분에서 제품별 경고문 또한 제공하고 있습니다 . 경고...
  • Page 7 서의 기술 자료를 읽고 , 유체 및 솔벤트 제조업체의 경고를 읽으십시오 . 재료에 대한 전체 정 보가 필요하면 유통업체 또는 대리점에게 MSDS 를 요청하십시오 . 장비는 매일 점검하십시오 . 마모되었거나 손상된 부품이 있으면 즉시 수리하거나 정품 ASM 부품 • 으로 교체하십시오 .
  • Page 8 部件辨认 구성품 식별 Component Identification / Component Identification / 部件辨认 / 구성품 식별 Stand ti10381a English 中文 한국어 Pressure Control 压力控制器 압력 제어기 ON/OFF switch ON/OFF 开关 온 / 오프 스위치 Pressure Guage (not on all models) 压力表 （并非所有型号都有） 압력 게이지 ( 일부 모델에는 없음 ) Power Cord 电源线...
  • Page 9 部件辨认 구성품 식별 Component Identification / Component Identification / 部件辨认 / 구성품 식별 Hi-Boy ti10306a 中文 한국어 English Pressure Control 压力控制器 압력 제어기 ON/OFF switch ON/OFF 开关 온 / 오프 스위치 Pressure Guage (not on all models) 压力表 （并非所有型号都有） 압력 게이지 ( 일부 모델에는 없음 ) Power Cord 电源线...
  • Page 10 泄压步骤 압력 해제 절차 Pressure Relief Procedure / Pressure Relief Procedure / 泄压步骤 / 압력 해제 절차 English 中文 한국어 Follow this Pressure Relief 只要停止喷涂并进行设备清 스프레이 작업을 정지할 때 Procedure whenever you 洗、检查、维修或运输之前， 와 장비를 청소 , 점검 , 수 stop spraying and before 都要按照此泄压步骤进行...
  • Page 11 泄压步骤 압력 해제 절차 Pressure Relief Procedure / Grounding / 接地 / 접지 English 中文 한국어 The sprayer must be 必须将喷涂机接地。通过接 분무기는 반드시 접지해야 grounded. Grounding 地，可给电流提供短路时逃 합니다 . 접지를 하면 회로 reduces the risk of electric 逸的通路，减少出现电击的 단락 시 전류가 빠져나갈 길 危险。...
  • Page 12 泄压步骤 압력 해제 절차 Pressure Relief Procedure / Ground 120 volt plug ti4297a Power Requirements Extension Cords • Do not modify plug! If it will • 100-120V units require • Use an extension cord with an • If an extension cord is neces- not fit in outlet, have grounded 100-120 VAC, 50/60 Hz, 11A, undamaged ground contact.
  • Page 13 泄压步骤 압력 해제 절차 Pressure Relief Procedure / ti5851a ti5850a Pails • Solvent and oil/based fluids: • Do not place pail on a noncon- • Grounding a metal pail: con- • To maintain grounding follow local code. Use only ductive surface such as paper nect a ground wire to the pail continuity when flushing conductive metal pails, placed...
  • Page 14 Tighten securely. 将 ASM 无气软管连接到 将软管的另一端连接到喷 牢牢拧紧。 取下喷嘴护罩。 喷涂机上。 枪上。 牢牢拧紧。 ASM 에어리스 호스를 도 호스의 반대쪽 끝을 건에 단단히 조입니다 . 팁 가드를 제거합니다 . 장기에 연결하고 연결합니다 . 단단히 조입니다 . 312392C...
  • Page 15 Check inlet strainer for Fill throat packing nut Turn power OFF. Plug power supply cord clogs and debris. with ASM Packing Seal to into a properly grounded prevent premature electrical outlet. packing wear. Do this each time you spray.
  • Page 16 设置 설치 Setup / ti8326a Flush Turn prime valve down. 10 Place siphon tube set in grounded metal pail pratially filled with flushing fluid. See Grounding, page 13. Do steps 1- 6 of Startup, page 17, to flush out storage oil shipped in sprayer.
  • Page 17 起动 작동 시작 Startup / Startup / 起动 / 작동 시작 1/4 turn ti8327a ti8325a ti8324a Turn pressure control to Turn power ON. Increase pressure Turn prime valve lowest pressure. 1/4 turn to start motor. horizontal.Take spray gun Allow fluid to circulate trigger safety OFF.
  • Page 18 起动 작동 시작 Startup / Paint Flush Flush ti10313a Hold gun against Inspect for leaks. Do not Place siphon tube in paint Trigger gun again into grounded metal flushing stop leaks with hand or a pail. flushing pail until paint pail.
  • Page 19 起动 작동 시작 Startup / ti10313a ti10314a Move gun to paint pail and 10 Screw tip assembly onto trigger for 20 seconds. Set gun. Tighten. For gun gun safety ON. assembly instructions, see gun manual, 312363, 312364, 312365. 将喷枪移向涂料桶并扣动 10 将喷嘴组件旋到喷枪上。 扳机...
  • Page 20 起动 작동 시작 Startup / Heavy Edges ti2758a ti2757a Spray test pattern. Adjust Use smaller tip size if Hold gun perpendicular, Trigger gun before moving. pressure to eliminate pressure adjustment 10-12 in. from surface. Release before stopping. heavy edges. cannot eliminate heavy Spray back and forth;...
  • Page 21 起动 작동 시작 Startup / Clearing Clogs / 清除堵塞物 / 막힌 곳 뜷기 ti10316a ti9047a ti9046a ti10315a ti9047a ti9046a Release trigger, put safety ON. Rotate Spray Tip. Take Put safety ON. Return Spray Tip to original position. Take safety OFF. Trigger gun to clear clog. safety OFF and continue spraying.
  • Page 22 清洗 청소 Cleanup / Cleanup / 清洗 / 청소 ti2758a ti9050a ti10311a Relieve Pressure, Remove guard and Remove siphon tube set Place siphon tube in page 10. Spray Tip. For additional from paint. Wipe excess flushing fluid. Use water information, see gun paint off outside of for water base paint and manual 312363,...
  • Page 23 清洗 청소 Cleanup / ti5313a 1/4 Turn ti83278a ti8326a ti2599a Waste ti8325a Turn prime valve Hold gun against paint Stop triggering gun. Move While continuing to trigger horizontal. pail. Take trigger safety gun to waste pail, hold gun, turn prime valve OFF.
  • Page 24 清洗 청소 Cleanup / ti8327a ti8324a Flush ti2599c ti9053b ti4296a Raise siphon tube above 10 Close drain valve. Trigger 11 Turn pressure control 12 If you have a filter flushing fluid. gun into flushing pail to knob all the way down installed on your purge fluid from hose.
  • Page 25 清洗 청소 Cleanup / Pump Armor ti2783a ti2895a 13 Remove filter from gun if 14 If flushing with water, 15 Wipe sprayer, hose and installed. Clean and flush again with mineral gun with a rag soaked in inspect. Install filter. See spirits or Pump Armor water or mineral spirits.

  • Page 26: Technical Data

    Technical Data Technical Data Power requirements ..........100/120V AC, 50/60 hz, 11A, 1 phase 240V AC, 50/60 hz, 7.5A, 1 phase Generator required .
  • Page 27 기술 자료 기술 자료 전기 사양 ......100/120V AC, 50/60 hz, 11A, 단상 240V AC, 50/60 hz, 7,5A, 단상 필요한...
  • Page 28 With the exception of any special, extended, or limited warranty published by ASM, ASM will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by ASM to be defective.

This manual is also suitable for:

Zip-spray 2100 plus 240vL1900 plus 110vL1900 plus 240vAllpro mach 5400 plus 110vZip-spray 2300 plus 110vAllpro mustang 4700 plus 110v