Tuningto The Next Programmed Channel; Tuningto A Specific Channel; (Programmed Or Unpmgrammed); Switching Between Two Channels Using Surllocke - Toshiba 40G300U Owner's Manual

Tuningto the next programmed
channel
To tune to the next programmed channel:
OH
Press (_ or _T_3on the remote control or TV control
panel.
Note: This feature will not work unless you
program channels into the TV's channel memory
(_, page 31).
Tuningto a specific channel
(programmedor unprogrammed)
Tuning analog channels:
Press the Channel Number (0-9) on the remote
control. For example, to select channel 125, press 1,2,
5, then @.
Tuning digital channels:
Press the Channel Number (0-9) on the remote
control, followed by the dash (@) button and then
the sub-channel number. For example, to select digital
channel 125-1, press i, 2, 5, -, 1, then @.
Note: If a digital channel is not programmed--
either through the automatic channel scan (_
page 31) or the Channel add function (_ page
32)--you will have to tune the RF channel using
the Channel Number and dash ((!_)) on the
remote control.
Switchingbetweentwo channels
usingChannelReturn
The Channel Return feature allows you to switch
between two channels without entering an actual
channel number each time.
1 Select the first channel you want to view.
2 Select a second channel using the Channel
Number buttons (and the dash ((_)) button if
selecting a digital channel).
CH RTN Press O on the remote control. The previous
CH RTN
channel will display. Each time you press O , the
TV will switch back and forth between the last two
channels that were tuned.
Note: if you press C_TN from a non-antenna
input, the TV will return to the last-viewed
input.
Switchingbetween two channels
usingSurfLock
TM
The SurfLock
TM
feature temporarily "memorizes" one
OH FITN
channel to the O button, so you can return to that
channel quickly from any other channel by pressing
OH RTN . OH RTN
O • To memorize
achannel to the
O
button:
1 Tune the TV to the channel you want to program
• OH RTN
mtothe © button.
CH RTN .
Press and hold O for about 2 seconds until
the message "Memorized" appears on-screen.
CH FITN
The channel has been programmed to the O
button.
3 You can then change channels repeatedly, and
CH RTN
when you press O , the memorized channel
will be tuned.
The TV will return to the memorized channel one
OH RTN
time only. Once you press O and then change
channels again, the CH RTN memory will be cleared
and the button will function as Channel Return,
by switching back and forth between the last two
channels that are tuned.This feature also works for
external inputs.
SelecUng the picture size
You can view many program formats in a varie b, of
picture sizes--Natural, TheaterWide 1, TheaterWide
2,TheaterWide 3, Full, 4 :3ItB, Native,
a nd Dot by Dot
(available in PC Mode Only).
Note: The "picture size" illustrations are
examples only. The format of the image (in any
of the picture sizes) will vary depending on the
format of the signal you are currently watching.
Select the picture size that displays the current
program the way that looks best to you.
You can save separate picture size preferences for
each input on your TV.
To select the picture size using the remote
control:
1
2
PlC SiZE
Press © on the remote control.
While the
Picture Size
screen is open, you can do
one of the following to select the desired picture
size:
PiG
SIZE
• Repeatedly press O
• Press the corresponding Number button (0-6)
while the
Picture Size
screen is open.
• Press A or Y while the
Picture Size
screen is
open.
(comin ued)
39
40_46 55G300U EN-ASindb 89 2010/3/16 _@ 05:48:56