Download  Print this page

Toshiba Regza 40RF350U Owner's Manual

Integrated high definition lcd television
Hide thumbs


Quick Links

Integrated High Definition
LCD Television
For an overview of steps for setting up your new TV, see page 10.
Note: To display a High Definition picture, the TV must be receiving a
High Definition signal (such as an over-the-air High Definition TV
broadcast, a High Definition digital cable program, or a High Definition
digital satellite program). For details, please contact your TV antenna
installer, cable provider, or satellite provider.
All Rights Reserved
Owner's Record
The model number and serial number are on the back of
your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshiba dealer about this TV.
Model number:
Serial number:



  Also See for Toshiba Regza 40RF350U

  Related Manuals for Toshiba Regza 40RF350U

  Summary of Contents for Toshiba Regza 40RF350U

  • Page 1 Owner’s Record The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. Model number: Serial number: VX1A00065000...
  • Page 2: Child Safety

    Dear Customer, Thank you for purchasing this Toshiba LCD TV. This manual will help you use the many exciting features of your new LCD TV. Before operating your LCD TV, please read this manual completely, and keep it nearby for future reference.
  • Page 3: Important Safety Instructions

    Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
  • Page 4 Care For better performance and safer operation of your TOSHIBA TV, follow these recommendations and precautions: 29) If you use the TV in a room whose temperature is 32 ºF (0 ºC) or below, the picture brightness may vary until the...
  • Page 5: Choosing A Location For Your Lcd Tv

    Choosing a location for your LCD TV To Display your LCD TV on the included Pedestal Stand: Observe the following safety precautions: 1) Read and Follow the pedestal assembly instructions included with the pedestal. CAUTION: Before beginning pedestal assembly, carefully lay the front of the LCD Panel face down on a flat, cushioned surface such as a quilt or blanket.
  • Page 6: Fcc Declaration Of Conformity

    • Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications to this equipment not expressly approved by Toshiba could void the user’s authority to operate this equipment. Important notes about your LCD The following symptoms are technical limitations of LCD Display technology and are not an indication of malfunction;...
  • Page 7: Table Of Contents

    Chapter 1: Introduction ......9 Welcome to Toshiba ....... . 9 Features of your new TV .
  • Page 8 Limited Canadian Warranty for Toshiba Brand Flat Panel Televisions ... 81 Index ........84...
  • Page 9: Chapter 1: Introduction

    Welcome to Toshiba Thank you for purchasing this Toshiba LCD TV, one of the most innovative LCD TVs on the market. This digital television is capable of receiving analog basic, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming.
  • Page 10: Overview Of Steps For Installing, Setting Up, And Using Your New Tv

    Inadequate ventilation may cause overheating, which will damage the TV. THIS TYPE OF DAMAGE IS NOT COVERED UNDER THE TOSHIBA WARRANTY. Do not plug in any power cords until AFTER you have connected all cables and devices to your TV.
  • Page 11: Tv Front And Side Panel Controls And Connections

    TV front and side panel controls and connections TV front Illumination — Power indicator This slit will be illuminated by the blue LED back light. See “Selecting the Blue LED Illumination level” on page 45 for additional information. Green and Yellow LEDs Green = See “LED indications”...
  • Page 12: Tv Back Panel Connections

    (with standard stereo audio inputs) for connecting devices with component video output, such as a Toshiba DVD player with ColorStream Note: Component video cables carry only video information; separate audio cables are required for a complete connection.
  • Page 13: Chapter 2: Connecting Your Tv

    ® (ColorStream is Toshiba’s brand of component video.) These cables are typically color-coded red, green, and blue. Separate audio cables are required for a complete connection. Note: Component video cables provide better picture performance than a standard (composite) video or S-video cable.
  • Page 14: Connecting A Vcr And Antenna Or Cable Tv (No Cable Box)

    Connecting a VCR and antenna or Cable TV (no Cable box) TV upper back panel TV lower back panel You will need: coaxial cables • standard A/V cables • – For better picture performance, if your VCR has S-video, use an S-video cable (plus the audio cables) instead of the standard video cable.
  • Page 15: Connecting A Vcr With S-Video And A Cable Box

    Connecting a VCR with S-video and a cable box An S-video connection will provide better picture performance than a standard (composite) video cable. TV upper back panel TV lower back panel You will need: coaxial cables • S-video cable • –...
  • Page 16: Connecting A Dvd Player With Colorstream

    Connecting a DVD player with ColorStream and a satellite receiver ® Your TV has two sets of ColorStream AUDIO COMPONENT VIDEO S-VIDEO VIDEO DVD player with component video From satellite dish AUDIO COMPONENT VIDEO VIDEO Satellite S-VIDEO Satellite receiver with component video You will need: coaxial cables •...
  • Page 17: Connecting A Device To The Ir Out Infrared Terminal Using The Ir Blaster Cable For Ir Pass-Through Device Control

    You can use the TV’s IR OUT terminal (infrared pass- through) to remotely operate (through the TV) many infrared remote-controlled devices (such as Toshiba infrared remote- controlled VCRs or DVD players) enclosed within an entertainment center or similar cabinet. Without the IR OUT connection, the device typically would need to be visible to operate it remotely.
  • Page 18: Connecting A Camcorder

    Connecting a camcorder You will need: standard A/V cables • – For better picture performance, if your camcorder has S-video, connect an S-video cable (plus the audio cables) to VIDEO 1 on the TV back instead of the VIDEO 2 on the TV right side panel.
  • Page 19: Connecting An Hdmi Or Dvi Device To The Hdmi Input

    ™ Connecting an HDMI or DVI device to the HDMI input The HDMI input on your TV receives digital audio and uncompressed digital video from an HDMI source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device. This input is designed to accept HDCP (High-Bandwidth Digital-Content Protection) program material in digital form from EIA/CEA-861-D–compliant...
  • Page 20: Ce-Link Connection

    The CE-Link feature uses the CEC technology as regulated • by the HDMI standard. This feature is limited to models incorporating Toshiba’s • CE-Link. However, Toshiba is not liable for those operations. Refer to individual instruction manuals for compatibility information.
  • Page 21: Connecting A Digital Audio System

    Connecting a digital audio system The TV’s DIGITAL AUDIO OUT terminal outputs a Dolby Digital g or 2-channel down-mixed PCM (pulse-code modulation) signal for use with an external Dolby decoder or other external audio system with optical audio input. You will need: optical audio cable (Use an optical audio cable that has the •...
  • Page 22: Connecting A Personal Computer (Pc)

    Connecting a personal computer (PC) With either the PC IN or HDMI connection, you can watch your computer’s display on the TV and hear the sound from the TV’s speakers. To connect a PC to the PC IN terminal on the TV: When connecting a PC to the PC IN terminal on the TV, use an analog RGB (15-pin) computer cable and a PC audio cable.
  • Page 23: Chapter 3: Using The Remote Control

    Chapter 3: Using the remote control Installing the remote control batteries To install the remote control batteries: Slide the battery cover off the back of the remote control. Install two “AA” size alkaline batteries. Match the + and – symbols on the batteries to the symbols on the battery compartment.
  • Page 24: Learning About The Remote Control

    Learning about the remote control The buttons used for operating the TV only are described here. For the CE-Link remote control functions, see the section “Using CE-Link” (- page 66). For a complete list of the remote control’s functions, see the remote control functional key chart (- pages 25–26).
  • Page 25: Remote Control Functional Key Chart

    Remote Control functional key chart REMOTE Toshiba TV CABLE CONTROL KEY (TV) MODE Remote control device mode selection SELECT s TV SLEEP Sleep timer POWER Power Power Digit 1 Digit 1 Digit 2 Digit 2 Digit 3 Digit 3 Digit 4...
  • Page 26 REMOTE Toshiba TV CABLE CONTROL KEY (TV) CH RTN/ Previous Previous DVD RTN channel channel On-screen s TV RECALL display Sound MUTE Sound mute mute Slow FWD* SLOW Slow REW* SKIP z DAY+ SKIP Z DAY– Rewind* Rewind PAUSE/STEP Pause*...
  • Page 27: Using The Remote Control To Operate Your Other Devices

    Note: The TV remote control is preprogrammed to operate most Toshiba devices. To operate a non-Toshiba device or a Toshiba device that the remote control is not preprogrammed to operate, you will need to program the remote control. See “Programming the remote control to operate your other...
  • Page 28: Searching And Sampling The Code Of A Device (8500)

    Searching and sampling the code of a device (8500) If you do not know the device code for a particular device, you can cycle the remote control through the available codes for that device mode and sample the functions to find the code that operates the target device.
  • Page 29: Multi-Brand Remote Control Device Codes

    Multi-brand remote control device codes Brand Code Toshiba 01524 Cable boxes Brand Code A-Mark 10008, 10144 10237, 10003, 10008, 10014, 10017 Accuphase 10003, 10014, 10017 Acorn 10237 Action 10237 Active 10237 Americast 10899 Amino 11822 Archer 10237 10276 Bell & Howell...
  • Page 30 Ultrasat 11806 Uniden 10724, 10722 Voom 10869 Zenith 11856 DVDs Brand Code 3D LAB 20503, 20539 Accurian 21072, 21416 Advent 21016 Afreey 20698 Aiwa 20641 Akai 20695, 20705, 20770, 20899, 21089 Alba 20672, 20717 Alco 20790 Allegro 20869 Apex Digital 20533, 20672, 20717, 20755, 20794, 20796,...
  • Page 31 20571, 20717, 20790 Technics 20490, 20703 Technika 20770 Tevion 20651 Theta Digital 20571 Thomson 20522, 20511 Tivo 21503, 21588 Toshiba 20503, 20573, 20539, 20695, 21045, 21154, 21503, 21588, 21854 Unimax 20770 Universum 20591 Urban Concepts 20503, 20539 US Logic 20839...
  • Page 32 Curtis Mathes 30060, 30035, 30162, 30240, 30000, 30041, 30278, 30432, 30760, 31035 Cybernex 30240 CyberPower 31972 Daewoo 30037, 30045, 30278, 30020, 30046, 30561, 31278 Daytron 30037, 30278, 30020 Dell 31972 Denon 30081, 30042 Derwent 30041 DirecTV 30739 Dual 30000 Durabrand 30039, 30038 Dynatech 30240, 30000...
  • Page 33 Thomson 30060, 30041, 30202 Tisonic 30278 Tivo 30618, 30636, 30739, 31996 30240, 30000, 30208 TNIX 30037 Tocom 30240 Toshiba 30240, 30045, 30000, 30043, 30209, 30041, 30062, 30210, 30845, 31008, 31145, 31972, 31996 Tosonic 30278 Totevision 30037, 30240 Touch 31972 Trix...
  • Page 34 Samsung 30739 Sonic Blue 30614, 30616 Sony 30636, 31972 Stack 9 31972 Systemax 31972 Tagar Systems 31972 Tivo 30618, 30636, 30739 Toshiba 31008, 31972, 31996 Touch 31972 Viewsonic 31972 Voodoo 31972 ZT Group 31972 Cable/PVR Combo Brand Code Americast 10899...
  • Page 35 41058, 41441, 41258, 41622, 41658, 41758, 41858 Stereophonics 41023 Sunfire 41313 Teac 41074, 41390 Technics 41308, 41518, 40309, 41633 Thorens 41189 Toshiba 40135, 40842, 41788 Venturer 41390 Victor 40074 Wards 40189, 40014 Yamaha 41023, 40176, 40186, 41176, 41276, 41331, 41375 Zenith...
  • Page 36: Chapter 4: Menu Layout And Navigation

    Chapter 4: Menu layout and navigation Main menu layout The tables below and on the next page provide a quick overview of your TV’s menu system. To open the main menus (illustrated below), press Y on the remote control or TV control panel. Icon Item Mode...
  • Page 37: Setup/Installation Menu Layout

    THINC Applications CE-Link Player Control Channel Browser Favorites Browser * Toshiba Home Interactive Network Connection. Chapter 4: Menu layout and navigation Option S [Opens the Input Configuration menu] S [Start] S [Scans for new channels on ANT] S [Opens the Channel Add/Delete menu]...
  • Page 38: Navigating The Menu System

    Navigating the menu system You can use the buttons on the remote control or TV control panel to access and navigate your TV’s on-screen menu system. Press Y to open the menu system. • When a menu is open, use the up/down/left/right arrow •...
  • Page 39: Chapter 5: Setting Up Your Tv

    Chapter 5: Setting up your TV Selecting the menu language You can choose from three different languages (English, French and Spanish) for the on-screen display of menus and messages. To select the menu language: Press Y and open the Preferences menu. Highlight Menu Language and press c.
  • Page 40: Programming Channels Into The Tv's Channel Memory

    Programming channels into the TV’s channel memory When you press < or , on the remote control or TV control panel, your TV will stop only on the channels you programmed into the TV’s channel memory. Follow the steps below to program channels into the TV’s channel memory.
  • Page 41: Setting The Auto Input Feature

    To add a channel to the channel memory: Highlight the unchecked box next to the channel number you want to add, and then press T to check the box. To manually add digital subchannels on a physical channel: Use the Channel Numbers and the Dash (=) on the remote control to enter the channel number (for example, 56–1).
  • Page 42: Labeling Channels

    Press B or b to select the mode field you want to set. Auto Input Use this menu to enable your TV's automatic input switching feature when changing modes on your remote control. Enable Auto Input POWER SLEEP CABLE/SAT MODE SELECT CABLE/SAT VCR/PVR VCR/PVR...
  • Page 43: Setting The Hdmi ™ Audio Mode

    To remove channel labels: Open the Channel Labeling window. Press < or , to select the channel for which you want to remove the label. Press BbC c to highlight No Label and press T. Channel Labeling {No Label} A&E Press CH UP/DOWN to ABCFAM change channels.
  • Page 44: Viewing The Digital Signal Meter

    Viewing the digital signal meter You can view the digital signal meter in the ANT digital TV input source only. To view the digital signal meter: Press Y and open the Setup menu. Highlight Installation and press T. A new set of Installation menu icons will appear, as shown below.
  • Page 45: Selecting The Blue Led Illumination Level

    Highlight Yes and press T. The TV will turn off automatically after a few seconds. After the TV turns off, unplug the TV power cord and then plug it in again to complete the reset process. System Information Press YES to confirm. After the TV turns off, unplug it and plug it back in to complete the reset.
  • Page 46: Chapter 6: Using The Tv's Features

    Chapter 6: Using the TV’s features Selecting the video input source to view To select the video input source to view: Press + on the remote control or TV control panel. And then either: a) Press 0–8; or b) Repeatedly press Bb on the remote control and then press T to change the input;...
  • Page 47: Labeling The Video Input Sources

    Labeling the video input sources You can label each video input source according to the type of device you connected to each source, from the following preset list of labels: – – (default label) • Audio Receiver • Cable • Compact Disc •...
  • Page 48: Tuning Channels

    Tuning channels Tuning channels using the ™ Channel Browser ™ The Channel Browser provides an easy navigation interface for all your channels and inputs. This feature allows you to: Navigate the contents of all of your inputs. • Keep a list of your favorite channels (see “Favorites •...
  • Page 49: Setting The Channel Tuning Mode

    Elements of the Channel Browser ™ History TVLAND ABCHD Current list (History, ANT, Inputs, Favorites, or CE-Link) Input type Channel or input currently being viewed Channel or input that is currently highlighted in the browser Channels stored in the History List Channel labels To toggle among the available lists: , press B or b to toggle...
  • Page 50: Tuning To The Next Programmed Channel

    To set the Channel Tuning Mode: Press Y and open the Setup menu. Highlight Installation and press T. (A new set of Installation menu icons will appear, as shown below.) Open the Terrestrial menu, highlight Channel Tuning Mode, and then press B b to select your desired mode.
  • Page 51: Selecting The Picture Size

    Selecting the picture size You can view many program formats in a variety of picture sizes—Natural, TheaterWide 1, TheaterWide 2, TheaterWide 3, Full, 4:3 HD and Native. Note: The “picture size” illustrations are examples only. The format of the image (in any of the picture sizes) will vary depending on the format of the signal you are currently watching.
  • Page 52 TheaterWide 3 picture size (for letter box programs with subtitles) The picture is stretched wider to fill the width of the screen, • but only slightly stretched taller. The top and bottom edges are hidden. To view the hidden • areas (such as subtitles or captions), see “Scrolling the ®...
  • Page 53: Scrolling The Theaterwide Picture (Theaterwide 2 And 3 Only)

    Scrolling the TheaterWide (TheaterWide 2 and 3 only) You can set separate scroll settings for the TheaterWide 2 and TheaterWide 3 modes for each input. To set the scroll settings: Press Y and open the Video menu. Highlight Theater Settings and press T. Video Mode Sports...
  • Page 54: Selecting The Cinema Mode (480I And 1080I Signals)

    Selecting the cinema mode (480i and 1080i signals) When you view a DVD (3:2 pulldown processed) from a DVD player connected to the VIDEO 1, VIDEO 2, ColorStream HD-1, ColorStream HD-2 (component video), or HDMI inputs on the TV, smoother motion can be obtained by setting the Cinema Mode to Film.
  • Page 55: Adjusting The Picture Quality

    Adjusting the picture quality You can adjust the picture quality (Contrast, Back Light, DynaLight™, Brightness, Color, Tint, and Sharpness) to your personal preferences. Pressing C Selection Contrast lower Back Light* darker DynaLight** On/Off Brightness darker Color paler Tint reddish Sharpness softer * Back Light This feature adjusts the brightness of the entire screen.
  • Page 56: Using The Closed Caption Mode

    Using the closed caption mode Base closed captions The closed caption mode has two options: Captions—An on-screen display of the dialogue, narration, • and sound effects of TV programs and videos that are closed captioned (usually marked “CC” in program guides). Text—An on-screen display of information not related to •...
  • Page 57: Cc Selector

    CC Selector You can use the CC Selector to temporarily override the default analog caption mode (set in Base CC Mode) for a particular channel. However, once you change to another analog channel, the closed caption setting will automatically change back to the current Base CC Mode setting. You can also use the CC Selector to select digital closed caption services (if available).
  • Page 58: Selecting Stereo/Sap Broadcasts

    Selecting stereo/SAP broadcasts The multi-channel TV sound (MTS) feature allows you to output high-fidelity stereo sound. MTS also can transmit a second audio program (SAP) containing a second language, music, or other audio information (when provided by individual stations). When the TV receives a stereo or SAP broadcast, the word “STEREO”...
  • Page 59: Using The Stablesound ® Feature

    Using the StableSound ® feature The StableSound ® feature limits the highest volume level to prevent extreme changes in volume when the signal source changes (for example, to prevent the sudden increase in volume that often happens when a TV program switches to a commercial).
  • Page 60: Using The Locks Menu

    Using the Locks menu The Locks menu includes the Enable Rating Blocking, Edit Rating Limits, Channels Block, Input Lock, Front (control) Panel Lock, Game Timer, and New PIN Code features. You can use these features after entering the correct PIN code. Entering the PIN code Press Y and highlight the Locks menu icon.
  • Page 61: Blocking Tv Programs And Movies By Rating (V-Chip)

    Done • The additional rating system is not designed, transmitted, or controlled by the TV or Toshiba, nor is the availability of an additional rating system determined or controlled by Toshiba. Similarly, the rating of programs in an additional rating system is not determined, transmitted, or controlled by the TV or Toshiba.
  • Page 62: Blocking Channels

    Independent rating system for broadcasters Ratings Description and Content themes Mature Audience Only (This program is specifically designed to be viewed by adults and therefore may TV-MA be unsuitable for children under 17.) L) Crude or indecent language S) Explicit sexual activity V) Graphic violence Parents Strongly Cautioned (This program contains some material that many parents would find...
  • Page 63: Unlocking Programs Temporarily

    To block all channels at once: Highlight Block All in step 5 on previous page and then highlight Done and press T. To unblock all locked channels at once: Highlight Allow All in step 5 on previous page and then highlight Done and press T.
  • Page 64: Using The Gametimer

    ® Using the GameTimer You can use the GameTimer to set a time limit for playing a video game (30–120 minutes). When the GameTimer expires, the TV enters Input Lock mode and locks out the input source for the video game device. ®...
  • Page 65: Using The Pc Settings Feature

    Using the PC settings feature You can view an image from a PC on the TV screen. When a PC is connected to the TV's PC IN terminal, you can use the PC Settings feature to make adjustments to the image. If the edges of the picture are cut off, readjust the Horizontal Position and Vertical Position.
  • Page 66: Setting The Sleep Timer

    Using CE-Link This is a new feature that uses CEC technology and allows you to control Toshiba CE-Link compatible devices from the TV remote via HDMI connection (- page 20). When the Enable CE-Link item in the CE-Link setup menu (- page 68) is set to On, individual CE-Link functions also set to On will be activated.
  • Page 67: Ce-Link Input Source Selection

    CE-Link Player Control menu functions: Press C and open the THINC Applications menu. Press B or b to highlight CE-Link Player Control and press T. THINC Applications CE-Link Player Control Channel Browser Favorites Browser Press B or b to select the item you want to control and press T.
  • Page 68: Using The Hdmi Settings Feature

    To set the CE-Link Setup: Press Y and open the Setup menu. Highlight CE-Link Setup and press T. Setup Installation CE-Link Setup Sleep Timer HDMI Settings PC Settings Blue LED Illumination High Power-On Mode Power-Saving Press B or b to highlight Enable CE-Link. CE-Link Setup Enable CE-Link TV Auto Input Switch...
  • Page 69: Displaying Tv Status Information

    Displaying TV status information To display TV status information using RECALL: Press E on the remote control. The following information will display (if applicable): Current input (ANT, VIDEO 1, etc.) • If ANT is the current input, either “CABLE” (for cable TV) •...
  • Page 70: Chapter 7: Using The Tv's Advanced Features

    Chapter 7: Using the TV’s advanced features Using the advanced picture settings features Using dynamic contrast When dynamic contrast is set to Low, Middle, or High, the TV will detect changes in the picture quality that affect the appearance of your contrast settings and then automatically adjust the video.
  • Page 71: Selecting The Color Temperature

    Selecting the color temperature You can change the quality of the picture by selecting from three preset color temperatures (Cool, Medium, and Warm), as described below. Mode Picture Quality Cool blueish Medium neutral Warm reddish To select the color temperature: Press Y and open the Video menu.
  • Page 72: Using Mpeg Noise Reduction

    Using MPEG noise reduction The MPEG noise reduction feature allows you to reduce visible interference caused by MPEG compression. Choices for MPEG noise reduction are Off, Low, Middle, and High. Off is automatically selected when this feature is disabled (“grayed out”). To select the MPEG noise reduction level: Press Y and open the Video menu.
  • Page 73: Using The Xvycc Selection Feature

    The Select Standard Color window will be displayed. Press B or b to highlight the color you want to adjust, and then press T. Select Standard Color Base Colors Green Blue Yellow Magenta Cyan The Color Adjustment window will be displayed. Press B to freeze the picture.
  • Page 74: Using The Game Mode Feature

    Using the Game Mode feature You can use the Game Mode feature for shorter frame delays when playing a video game requiring split-second timing between the on-screen display and input from the controller (such as music creation and high-action games). This feature is more effective for 480i and 1080i input signals.
  • Page 75: Chapter 8: Troubleshooting

    Chapter 8: Troubleshooting General troubleshooting Before calling a service technician, please check this chapter for a possible cause of the problem and some solutions you can try. Black box on-screen The closed caption feature is set to one of the Text modes •...
  • Page 76 The V-Chip feature is available for the U.S. V-Chip • system only (- page 61). No CE-Link operation • The CE-Link feature is available for Toshiba CE-Link compatible devices. • Make sure the HDMI cables with the HDMI Logo ) are used.
  • Page 77: Led Indications

    If, after trying the solutions, the problem still exists: In the U.S., call TACP Consumer Solutions at 1-800-575-5469. • In Canada, locate the nearest Toshiba authorized service depot by directing your web browser to; click • “Home Entertainment,” and then click “Support.”...
  • Page 78: Chapter 9: Appendix

    3 V(p-p), 3.5 mm mono socket PC INPUT: 15-Pin D-sub Analog RGB Dimensions 40RF350U: Width: 36-7/8 inches (934 mm) Height: 25 inches (632 mm) Depth: 12 inches (302 mm) 46RF350U: Width: 42-1/4 inches (1,070 mm) Height: 28-1/8 inches (713 mm)
  • Page 79: Acceptable Signal Formats For Pc In And Hdmi Terminals

    Acceptable signal formats for PC IN and HDMI terminals PC IN signal formats Note: Depending on the connected PC, the following status may occur; incorrect display, false format detection, picture position failure, blur, or judder. But this is not a malfunction of your TV. Format Resolution 640 ×...
  • Page 80: Limited United States Warranty

    Limited United States Warranty for LCD Televisions 26” and Larger Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS LCD TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.
  • Page 81: Limited Canadian Warranty

    Toshiba modifications to the Television; h. Service of a Television on which the TOSHIBA label or logo, rating label or serial number have been defaced or removed; On-site service and repair of the Television; and...
  • Page 82 If, after following all of the operating instructions in this manual and checking the “Troubleshooting” section, you find that service is needed: (1) To find the nearest ASP, visit TCL’s web site at, or call toll free 1-800-268-3404 (2) Present your bill of sale or other proof of purchase to the ASP.
  • Page 83 A copy of the GPL source code in this product may be obtained by contacting Toshiba Consumer Solutions at (800)631-3811. There will be a charge to cover the costs of providing the source code. A copy of the LGPL source code in this product may be obtained by contacting Toshiba Consumer Solutions at (800)631-3811.
  • Page 84: Index

    Index Antenna cable ... 13 ... 39 Antenna input configuration ... 58 Audio quality adjustments Audio system connection ... 21 ... 53 Auto aspect Auto Input ... 41 ... 69 Auto power off Back of the TV ... 12 ... 56 Base closed captions Blocking channels ...
  • Page 85 Warranty ... 81 Canada U.S..80 WOW:SRS 3D ... 74 ... 74 WOW:SRS Focus WOW:SRS TruBass ... 74 ... 73 xvYCC Selection...
  • Page 86 MANUFACTURED BY CableClear, ColorStream, GameTimer, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C. Channel Browser, SurfLock, DynaLight, ColorMaster, TheaterLock, and THINC are trademarks of Toshiba America Consumer Products, L.L.C. REGZA is a registered trademark of Toshiba Corporation.

This manual is also suitable for:

Regza 46rf350u