Gem-P800 Commands - NAPCO GEM-P800 Installation Instructions Manual

WI850D GEM-P800 Installation Instructions
value of 1234, program the 4-digit User 1 Code
through Dealer Programming [95]. User 1 Arm/
Disarm code is also used to program User
Codes 2 - 8. By default, the User 1 code cannot
be re-programmed by the user.
If it is necessary to change the User 1 code, it
can be changed through downloading or Dealer
keypad programming. From Dealer Program
Mode, change the User 1 Code Lockout ([96-2]
LED=OFF) to disabled.
Your User 1 Code can be used to enter the User
Program Mode, where you can program other
User Codes. The following explains how you
will use this Code to program or erase additional
User Codes.
Entering User Program Mode
1. Enter
A 8
2. Enter User 1 Code (
1234
D
3. Press
,
ARMED STATUS AND
's
BLE LED WILL FLASH CONTINUOUSLY
KEYPAD WILL BEEP
G E M I N I
1
H
A 1 is displayed indicating
User 1 Code is programmed
and 2-8 are blank.
Zone LED Meaning
OFF User Arm/Disarm Code not programmed
Flashing User Arm/Code is currently being programmed
Steady User Arm/Disarm Code has been programmed
TABLE
5
Z L D
ONE ED EFINITION
10
While in User Program Mode, Zones 1 through 8
will light to indicate any User Codes presently
programmed. Follow the example below to pro-
gram User 2's code to 1923.
User Mode Programming Example:
1.Press
Zone 2 LED will Flash.
2.Enter
continue to flash until the 4th digit is en-
tered. The keypad will beep 4 times con-
firming a valid entry (Zone LED steady).
Deleting a User Code
Press the User number to be deleted, the key-
pad will beep twice and the zone LED will be
flashing indicating the user has been selected.
Press
user will now be OFF.
)
Exiting User Program Mode
(Default)
When you are done programming or erasing
H
SYSTEM TROU- User Codes, press
.
Status, and
4 .
TIMES
can test your new User Code. IMPORTANT:
You MUST exit User Program Mode before
testing your new User Code.

GEM-P800 Commands

User Commands
A1
Enter this command to turn on the Bell, keypad
sounder and keypad LED's for 2 seconds. The
-U P M
SER ROGRAM ODE
, keypad will beep twice and
2
, Zone 2 LED will
1923
, and the LED associated with the
F
to exit. The Armed,
C
H lights will stop flashing, and you
Bell Test
battery is tested during a Bell Test, and auto-
matically every *24 hours to ensure proper bat-
tery operation under load. The Alarm output
requires a battery in order to supply the speci-
fied output. If the battery cannot sustain the
load, a low battery indication will be displayed.
A battery test is also performed on power-up
after a 3 minute delay.
*A battery test occurs every 4 hours when
Household Fire [96-3] has been selected.
D
Easy Arm
Press this key to arm the panel. To disarm the
panel a valid Arm/Disarm code must be entered.
Requires Easy Exit/Easy Arm [21-2] to be en-
abled.
Interior
E
Enter this command to bypass all Exit/Entry Fol-
lower Zones or Home/Away Zones (only if the
system is programmed exclusively for Home/
Away with Delay zones).
Instant
F
Enter this command before or after arming to
remove the entry delay on Entry/Exit Zones.
The keypad ARMED LED will flicker rapidly.
Faulting a Exit/Entry Zone will result in an imme-
diate alarm.
Chime ON/OFF
A5
Enter this command to turn chime ON/OFF.
The Keypad will chime on any zone that has not