GRAUPNER S8474 Manual
  1. Manuals
  2. Brands
  3. GRAUPNER Manuals
  4. Control Unit
  5. S8474
  6. Manual
GRAUPNER S8474 Manual

GRAUPNER S8474 Manual

Pdb + sbec module, voltage, current, capacity, telemetry
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Manual
PDB + SBEC Module
Voltage, Current, Capacity, Telemetry
No. S8474

Advertisement

Table of Contents
loading

Related Manuals for GRAUPNER S8474

Summary of Contents for GRAUPNER S8474

  • Page 1 Manual PDB + SBEC Module Voltage, Current, Capacity, Telemetry No. S8474...
  • Page 2 2 / 2 S8474_PDB_SBEC_V_1_jh...

  • Page 3: Table Of Contents

    Index Introduction ................4 Service Centre ...............4 Intended use .................5 Package content ..............5 Technical Data ...............5 Declaration of conformity ............5 Symbols explication ...............6 Safety notes ................6 Montage and connections .............7 Programming the alarm threshold ..........7 Programming the User Setup ..........9 Ext. Switch ................10 Indication in the transmitter telemetry display .......10 Meaning of the red LED signals ...........10 Notes on environmental protection ........11...

  • Page 4: Introduction

    PDB + SBEC Module and first of all to safely control your models. If you experience any trouble during operation, take the instruc- tions to help or ask your dealer or Graupner Service Centre. Due to technical changes, the information may be changed in this manual without prior notice.

  • Page 5: Intended Use

     Dimensions - 35 x 35 x 7 mm  Weight - 25 grams Declaration of conformity S8474 PDB + SBEC Graupner/SJ declares that the product is conform to EU norms. EMC 2004/108/EC: EN 61000-6-3: 2007+A1:2011 EN 61000-6-1:2007 5 / 12...

  • Page 6: Symbols Explication

    Symbols explication Always observe the information indicated by this warning sign. Particularly those which are additionally marked with the words CAUTION or WARNING. The signal word WARNING indicates the potential for serious injury, the signal word CAUTION indicates possibility of lighter injuries. The signal words Note and Attention indicate potential damages to objects.

  • Page 7: Montage And Connections

    The update port allows the receiver update even with connected module. To update the PDB + SBEC Module please read the instruction before you use the "Firmware_upgrade_studio“ on www.graupner.de. Moreover the BEC voltage can be used to power for example an FPV camera. Update port...
  • Page 8 The following parameters can be set separately for all displays: Warning Time: here you can set for each display if and how long the alarm should be active for a specific value. Repeat Time: here you can set how often an alarm should be active when a specific value is reached.

  • Page 9: Programming The User Setup

    Page 5 Max Power Voltage        Here you can set the alarm threshold for maximum voltage.        The alarm threshold can be set between 0 and 25.0 V in steps ...

  • Page 10: Ext. Switch

    Ext. Switch Here you can set the 3 switch outputs.      The value is settable between high and low.             low indicates that the output is switched off (0 V) high indicates that the output is switched on (3 V) Factory setting: low Use example: to switch the video channel on the transmitter the...

  • Page 11: Notes On Environmental Protection

    The present construction or user manual is for informational pur- poses only and may be changed without prior notice. The cur- rent version can be found on the Internet at www.graupner.de on the relevant product page. In addition, the company Graupner has no responsibility or liability for any errors or inaccuracies that may appear in construction or operation manuals.

Table of Contents