IFM SmartLine AC3218 Operating Instructions Manual

IFM SmartLine AC3218 Operating Instructions Manual

As-i module

Advertisement

Quick Links

Operating instructions
AS-i SmartLine module
UK
AC3218
AC3219

Advertisement

Table of Contents
loading

Summary of Contents for IFM SmartLine AC3218

  • Page 1 Operating instructions AS-i SmartLine module AC3218 AC3219...
  • Page 2: Table Of Contents

    Contents 1 Preliminary note ���������������������������������������������������������������������������������������������������3 1�1 Explanation of symbols ����������������������������������������������������������������������������������3 2 Safety instructions �����������������������������������������������������������������������������������������������3 3 Functions and features ����������������������������������������������������������������������������������������4 4 Addressing �����������������������������������������������������������������������������������������������������������4 4�1 Addressing with the AC1154 addressing unit�������������������������������������������������4 5 Installation������������������������������������������������������������������������������������������������������������5 5�1 Installation of the device ��������������������������������������������������������������������������������5 5�2 Removal of the device �����������������������������������������������������������������������������������5 6 Electrical connection ��������������������������������������������������������������������������������������������6 6�1 Wiring�������������������������������������������������������������������������������������������������������������6 6�2 Connection analogue module AC3218 (0���20 mA) ���������������������������������������7...
  • Page 3: Preliminary Note

    1 Preliminary note Technical data, approvals, accessories and further information at www�ifm�com� 1.1 Explanation of symbols ► Instructions > Reaction, result → Cross-reference Important note Non-compliance may result in malfunction or interference� Information Supplementary note� 2 Safety instructions • Read this document before setting up the product and keep it during the entire service life�...
  • Page 4: Functions And Features

    3 Functions and features The slave receives data via the AS-Interface and converts them into analogue output signals� The AS-i module operates as a slave with bidirectional data transfer in the AS-i network� The data transfer from the host to the slave is asynchronous according to the AS-i profile S-7�3 and the AS-i specification V2�11�...
  • Page 5: Installation

    5 Installation 5.1 Installation of the device ► Install the device on a 35 mm DIN rail� ► Leave enough space between the unit and the top and bottom of the control cabinet to enable air circulation and to avoid excessive heating� ►...
  • Page 6: Electrical Connection

    6 Electrical connection The unit must be connected by a qualified electrician� The national and international regulations for the installation of electrical equipment must be adhered to� ► Disconnect power� ► Connect the unit� 6.1 Wiring AC3218 AC3219 actuator supply +24 V C1���C4 analogue output current (AC3218) V1���V4...
  • Page 7: 6�2 Connection Analogue Module Ac3218 (0

    6.2 Connection analogue module AC3218 (0...20 mA) 6.2.1 Connection of an actuator without separate voltage supply A 2-wire actuator is connected via the terminals C1���C4 and 0 V� C1...C4 The terminals O+ and O- are not used with actuators without separate voltage supply�...
  • Page 8: 6�2�3 Connection Of An Actuator With Separate 24 V Supply

    6.2.3 Connection of an actuator with separate 24 V supply An actuator with separate supply is I/U+ C1...C4 connected to the external 24 V via the terminals O+ and O-� The signal can be I/U- taken from the terminals C1���C4 and 0 V� 1: Analogue module 2: Actuator with separate supply 6.2.4 Electrical connection 0 V terminal...
  • Page 9: 6�3 Connection Analogue Module Ac3219 (0

    AC3xx8 1: Frequency converter ► As a remedy, use two current output modules� 6.3 Connection analogue module AC3219 (0...10 V) 6.3.1 Connection of an actuator with intrinsic supply V1...V4 An actuator with intrinsic supply (e�g� a voltmeter) is connected via the terminals V1���4 and O-�...
  • Page 10: 6�3�2 Connection Of An Actuator With Separate 24 V Supply

    6.3.2 Connection of an actuator with separate 24 V supply An actuator with separate supply is connected to the external 24 V via the terminals O+ and O-� The signal can be V1...V4 I/U+ taken from the terminals V1���V4 and 0 V� I/U- The terminals O- and 0 V must be con- nected to each other via a link�...
  • Page 11: Measuring Range

    8 Measuring range ► The measuring ranges, the states of the LEDs and their meaning are indicated in the following tables� 8.1 Analogue module AC3218 Range Units Units LEDs Meaning 0...20 mA dec. hex. O1...O4 analo- 0���20 mA 0000���20000 0000���4E20 nominal range 20�001���...
  • Page 12: Operation

    9 Operation ► Check the safe functioning of the unit� Display by LEDs: LED AS-i green lights AS-i voltage supply OK LED AUX green lights External voltage supply 24 V OK LEDs O1���O4 yellow light Analogue signal within the measuring range or no actuator connected�...
  • Page 13: Scale Drawing

    11 Scale drawing 25,4...

This manual is also suitable for:

Smartline ac3219

Table of Contents