Table of Contents
Advertisement
WARNING
For your own safety, read and understand all warnings and
operating instructions before using any tool or equipment.
WARNING
The 1" belt sander can be used for processing wood and
metal products. However, combining both wood dust and
metal filings can create a FIRE HAZARD. Make certain dust
collector is free of wood dust deposits before processing
metal products.
WARNING
Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contain chemicals
known to the State of California to cause cancer, birth defects
or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other
masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures vary, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area and work
with approved safety equipment. Always wear OSHA/NIOSH
approved, properly fitting face mask or respirator when using
such tools.
WARNING
Failure to follow these rules may result in serious personal
injury. Remember that being careless for even a fraction of a
second can result in severe personal injury.
WORK PREPARATION
• Wear proper apparel. Do not wear loose clothing, gloves,
neckties, rings, bracelets or other jewelry which may get
caught in moving parts of the tool.
• Nonslip protective footwear is recommended. Wear
protective hair covering to contain long hair.
• Wear eye and hearing protection. Always use safety
glasses. Eye protection equipment should comply with
ANSI Z87.1 standards. Hearing equipment should comply
with ANSI S3.19 standards.
• Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly. Never operate power tools when
tired, intoxicated or when taking medications that cause
drowsiness.
WORK AREA PREPARATION
• Keep work area clean. Cluttered work areas and benches
invite accidents.
• Work area should be properly lighted.
• Do not use the machine in a dangerous environment. The
use of power tools in damp or wet locations or in rain can
cause shock or electrocution.
• Three-prong plug should be plugged directly into properly
grounded, three-prong receptacle.
• Use the proper extension cord. Make sure your extension
cord is in good condition. It should have grounding prong
and should be of the correct gauge.
GENERAL SAFETY RULES
• Keep children and visitors away. Your shop is a potentially
• Make your workshop childproof with padlocks, master
• It should have a grounding prong and should be of the
TOOL MAINTENANCE
• Turn the machine "OFF", and disconnect the machine from
• Maintain all tools and machines in peak condition. Keep
• Follow instructions for lubricating and changing
• Check for damaged parts. Check for alignment of moving
• Poorly maintained tools and machines can further damage
• A guard or any other part that is damaged should be
TOOL OPERATION
• Avoid accidental start-up. Make sure that the tool is in the
• Use the right tool for your job. Do not force your tool or
• Disconnect tool when changing parts. Always use
• Don't force the workpiece on the machine. Damage to the
• Never leave tool running unattended. Turn the power off
• Do not overreach. Loss of balance can make you fall into a
• Never stand on tool. Injury could occur if the tool tips, or if
• Know your tool. Learn the tool's operation, application and
• Use a proper extension cord of the correct gauge. Your
• Handle workpiece correctly. Keep hands away from
• Turn tool off if it jams.
• Always support the workpiece against the table or backstop
• Always feed workpiece against the direction of the sanding
Think safety! Safety is a combination of operator common
sense and alertness at all times when tool is being used.
Do not attempt to operate tool until it is completely
assembled according to the instructions.
dangerous environment. Children and visitors can be
injured.
switches or remove switch keys to prevent any
unintentional use of power tools.
correct gauge.
the power source prior to inspection.
tools sharp and clean for best and safest performance.
accessories.
parts, binding, breakage, mounting and any other condition
that may affect tool's operation.
the tool or machine and/or cause injury.
repaired or replaced. Do not perform makeshift repairs.
"OFF" position before plugging in.
attachment to do a job for which it was not designed.
manufacturer recommended belts and disc.
machine and/or injury may result.
and do not leave tool until it comes to a complete stop.
working machine, causing injury.
you accidentally contact the cutting tool.
specific limitations before using it.
extension cord should have a grounding prong, and should
be in good condition.
moving parts.
when sanding.
rotation. To maintain control, properly support long or wide
work-pieces.
CAUTION
WARNING
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
1
1
Advertisement
Table of Contents
