CYBEX ONYX User Manual page 13

- The canopy is adjustable to various positions. The Canopy has a height
adjustment and a forward rotation function. To rotate open the zip
located at the top of the canopy.
The canopy has a fully ratcheting function to create complete coverage.
Simply pull on the front of the canopy to the desired position. The height can
be easily adjusted by simply sliding the canopy up or down the frame. The
entire canopy can also be tilted forward. For maximum coverage, unzip the
extra panel on top of canopy and pull forward.
- The canopy flap at the rear of the stroller can be rolled up and fixed with a
velcro fastener, if required.
11. USING THE HARNESS SYSTEM
a) To fasten the harness system insert left and right side fasteners into the
central harness buckle.
b) To tighten the belts pull the strap on the front of the central harness buckle.
c) To release the belt system press the release button located on the seat in
front of the belt lock while pulling at the shoulder belts.
d) To release the fasteners squeeze the grooves on left and right side of the
central harness buckle.
e) Adjust the length of the crotch strap with the corresponding slider.
WARNING: ALWAYS USE THE CROTCH STRAP IN
COMBINATION WITH THE WAIST BELT.
12. ADJUSTING THE HARNESS SYSTEM FOR NEWBORNS
a) Release the loops at the end of the shoulder straps from the triangle in the
belt system, situated at the bottom of the backrest under the seat cover.
b) Completely pull the shoulder straps out of the holes in the backrest.
c) Feed the shoulder straps through the two bottom holes. Make sure to
feed the straps back through the holes in the backrest mechanism and
re-attach them to the triangle.
d) To adjust the length of the shoulder straps to newborns please attach the
inner loop of the shoulder strap ends to the triangular ring. Switch back
to the upper holes as soon as the shoulder straps do no longer fit over the
child´s shoulders.
13. REMOVING THE HEADHUGGER AND SHOULDER PADS
(TOPAZ ONLY)
Remove the headhugger as soon as the headhugger does no longer fit over
the child´s shoulders.
a) Remove the velcros of the headhugger on the top left and right side on
the back of the seat cover.
b) Release the loops at the end of the shoulder straps from the triangle in the
belt system, situated at the bottom of the backrest under the seat cover.
c) Completely pull the shoulder straps out of the holes in the backrest.
14. REMOVING THE SEATCOVER
a) Slightly fold the stroller to reduce tension.
b) Remove the canopy from the stroller, if attached.
c) Take the seat cover's hooks (3) off the frame on left and right side
d) Open the press buttons (4) of the straps connected to the seat side panels
and the basket rear tube.
e) Open the flaps (5) which are fixed with velcro over the tubes, one on each
side.
f) Feed the strap with the slider (6) of the central harness buckle through the
hole in the seat fabric.
g) Feed the loops on the end of the shoulder straps through the triangle in
the backrest (7).
h) Feed the shoulder straps through the holes in the seat fabric (8).
i) Open the press buttons which are on the left and the right side from the
seat on the bottom from the fabric.
j) Pull the seat cover over the belt shifting button on the seat.
k) Slide the fabrics from the seat base tubes.
l) Reverse this procedure to refit the seat cover and the harness. Make sure
that the seat tubes slide back into the pockets inside the seat cover.
15. RECLINING THE LEG REST
a) Press the leg rest on both front edges and push down.
b) Simply lift the leg rest to put it back to the starting position.
16. RECLINING THE SEAT
a) Pull the recline lever at the back of the seat in order to recline the backrest
to the 4 different positions.
b) To raise lift the complete backrest up to required position.
17. CARRYING THE STROLLER
- Pull the flexible carring handle on right rear tube and lift the stroller.
18. ATTACHING THE RAINCOVER (OPTIONAL)
a) Extend the rain cover over the stroller like shown in the image
b) To fit the rain cover fasten the velcro strips around the frame at the top
and bottom on both sides of the buggy.
19. WARRANTY
The following warranty applies solely in the country where this product
was initially sold by a retailer to a customer. The warranty covers all
manufacturing and material defects, existing and appearing, at the date of
purchase or appearing within a term of two (2) years from the date of
5