ZIEHL-ABEGG FE2owlet-ECQ Assembly Instructions Manual
Ec-fans with top efficiency, motor size u
Hide thumbs
Also See for FE2owlet-ECQ:
- Assembly instructions manual (24 pages) ,
- Assembly instructions manual (24 pages)
Related Manuals for ZIEHL-ABEGG FE2owlet-ECQ
Summary of Contents for ZIEHL-ABEGG FE2owlet-ECQ
- Page 1 FE2owlet-ECQ Motor size U EC-fans with top efciency Assembly instructions Keep for reference! L-BAL-F062-GB 1547 Index 003 Part.-No. 00702389-GB...
-
Page 2: Table Of Contents
Assembly instructions FE2owlet-ECQ Content General notes .......... - Page 3 Assembly instructions FE2owlet-ECQ Service work ..........
-
Page 4: General Notes
We do not accept any liability for possible errors or omissions in the information con- tained in data, illustrations or drawings provided. ZIEHL-ABEGG SE is not liable for damage due to misuse, incorrect use, improper use or as a consequence of unauthorized repairs or modifications. -
Page 5: Safety Instructions
• Do not connect built-in fans to open flue pipes of gas and other firing devices. • The designated use of ZIEHL-ABEGG fans with VDE certification (see rating plate) assumes connection in a device or via a control unit. •... -
Page 6: Explanations Of Symbols
Assembly instructions FE2owlet-ECQ Safety instructions 2.3 Explanations of symbols Safety instructions are highlighted with warning triangles and are depicted according to the degree of hazard as follows. Attention! General hazardous area. Death or severe injury or significant property damage can... -
Page 7: Work On The Device
ZIEHL-ABEGG.These parts were specifically designed for the device. There is no guarantee that parts from non-original sources are designed and manufactured in correspondence with load and safety requirements. Parts and optional equipment not supplied by ZIEHL-ABEGG are not approved by ZIEHL-ABEGG for use. L-BAL-F062-GB 1547 Index 003 Part.-No. -
Page 8: Operator's Obligation Of Diligence
12100) or other structural protective measures. 3.2 Functional description ECQ motors from ZIEHL-ABEGG are highly efficient, electronically commuted motors (EC) with an integrated controller. They are designed exclusively for driving axial fans. The motors are designed for continuous operation (S1-operation) and are thermally protected. -
Page 9: Motor Protection
3.4 Note on the ErP directive ZIEHL-ABEGG SE wishes to point out that, based on the directive (EU) no. 327/2011 of the Commission of 30th of March 2011 for enforcing directive 2009/125/EC (hereinafter referred to as ErP directive), the operational area of certain fans within the EU is bound by certain prerequisites. -
Page 10: Disposal / Recycling
Assembly instructions FE2owlet-ECQ Mounting 3.6 Disposal / recycling Disposal must be carried out professionally and in an environmentally friendly way in accordance with the respective national legal stipulations. Separate the materials by type and in an environmentally friendly way. "... -
Page 11: Connection Lead & Terminal Box
Assembly instructions FE2owlet-ECQ Mounting 4.2 Connection lead & terminal box Information In demanding environments (wet areas, open air installation) all connections must incorporate water drainage curves. To ensure that water cannot penetrate through to the controller housing from the connections install a terminal box lower than the motor. -
Page 12: Connection Of The Motor
Assembly instructions FE2owlet-ECQ Mounting 4.4 Connection of the motor Danger due to electric current • The mains voltage must comply with the EN 50160 quality characteristics and the defined standard voltages in IEC 60038! • Connect fan only to electrical circuits that can be disconnected with an all-pole isolating switch. -
Page 13: Start-Up
Assembly instructions FE2owlet-ECQ Start-up Danger due to electric current • Connection to the 3 ~ 230 V line between two phases is not permitted! • A dangerous voltage (maximum line voltage) is applied at the black connecting wire (speed control input) when it is not used (speed 1). Therefore this wire must be connected to a terminal for insulation. -
Page 14: Diagnostics / Faults
Assembly instructions FE2owlet-ECQ Diagnostics / Faults 6 Diagnostics / Faults 6.1 Trouble shooting Type of error Possible cause Adjustment Fan does not No line voltage Check line voltage run (anymore) line failure Under - or overvoltage Short circuit winding Replace fan Thermal protection has trig- Check for free air passages;... -
Page 15: Service Work
• Bolted-on or pressed on impellers and/or wings may only be replaced by authorised ZIEHL-ABEGG SE staff. The manufacturer shall not be liable for damage caused through improper repair work. •... -
Page 16: Cleaning
Assembly instructions FE2owlet-ECQ Enclosure 7.2 Cleaning Danger due to electric current • Voltage supply for motor must be interrupted and secured against restoration! • Do not use any aggressive cleaning agents when cleaning. • Make sure that no water gets into the inside of the motor and electronics. -
Page 17: Ec Declaration Of Incorporation
Assembly instructions FE2owlet-ECQ EC Declaration of Incorporation For motors with one speed and corresponding quality mark rating plate) Authorization: FILE No. UL 1004-7 E347018 Electronically-Protected Motor - Component For motors with three speeds and corresponding quality mark rating plate) Authorization: FILE No. - Page 18 Assembly instructions FE2owlet-ECQ EC Declaration of Incorporation EN ISO Safety of machinery; safety distances to prevent danger zones being 13857:2008 reached by the upper limbs Note: The maintenance of the EN ISO 13857:2008 relates only to the installed accidental contact protection, provided that it is part of the scope of delivery.
-
Page 19: Manufacturer
If you have any questions about how to use our products or if you are planning special applications, please contact: ZIEHL-ABEGG SE Heinz-Ziehl-Straße D-74653 Künzelsau Phone 07940/16-0 Fax 07940/16-300 info@ziehl-abegg.de 8.4 Service address Please refer to the homepage at www.ziehl-abegg.com for a list of our subsidiaries worldwide. L-BAL-F062-GB 1547 Index 003 Part.-No. 00702389-GB 19/19...