Advertisement
INSTALLATION INSTRUCTIONS
IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR
SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.
FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN DEATH, SERIOUS INJURY OR SIGNIFICANT PROPERTY DAMAGE.
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH APPLICABLE BUILDING AND ELECTRICAL CODES, BY A QUALIFIED PERSON WHO IS FAMILIAR WITH THE CONSTRUCTION
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES
•
FULLY INSPECT LENS AND HOUSING OF THE FIXTURE PRIOR TO INSTALLATION. IF
DAMAGED, NOTIFY FACTORY.
•
TO AVOID ELECTRIC SHOCK: DISCONNECT ELECTRICAL POWER (LINE POWER)
BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•
VERIFY SUPPLY VOLTAGE IS SAME AS RATED FIXTURE VOLTAGE. THE ELECTRICAL
RATINGS OF THE FIXTURE ARE CLEARLY INDICATED ON THE PRODUCT LABEL.
•
BE CAUTIOUS OF ANY SHARP EDGES. WEAR PROPER SAFETY GEAR (SUCH AS
GLOVES AND SAFETY GLASSES) WHILE HANDLING.
CAUTION - RISK OF PERSONAL INJURY
ACCOUNT FOR SMALL PARTS AND DESTROY PACKING MATERIAL, AS THESE MAY BE
HAZARDOUS TO CHILDREN
CAUTION - RISK OF FIRE
•
MINIMUM 90º C SUPPLY CONDUCTORS.
•
NOT INTENDED FOR RECESSED INSTALLATION IN CEILINGS OR SOFFITS.
WARNING -
•
RISK OF FIRE OR ELECTRIC SHOCK—LUMINAIRE WIRING AND ELECTRICAL PARTS MAY
BE DAMAGED WHEN DRILLING FOR INSTALLATION OF RETROFIT ASSEMBLY
HARDWARE. CHECK FOR ENCLOSED WIRING AND COMPONENTS.
AVERTISSEMENT - RISQUE D'INCENDIE OU DE CHOC ÉLECTRIQUE. CÂBLAGE DU
LUMINAIRE ET PIÈCES ÉLECTRIQUES PEUVENT ÊTRE ENDOMMAGÉS LORS DU FORAGE
POUR L'INSTALLATION DU KIT DE CONVERSION À DEL. VÉRIFIER LE CÂBLAGE ET LES
COMPOSANTS CLOS
•
IF AC INPUT WIRING PASSES THROUGH FIXTURE HOUSINGS IN CONTINUOUS RUN
INSTALLATIONS, MAX AMBIENT ON ALL FIXTURES CONTAINING A FACTORY
INSTALLED BATTERY BACK UP SYSTEM IS 40°C.
THESE INSTRUCTIONS DO NOT ATTEMPT TO COVER ALL INSTALLATION AND MAINTENANCE SITUATIONS. FOR MORE INFORMATION OR QUESTIONS REGARDING THE INSTALLATION
OR USE OF THE ESSENTIALS FIXTURE, CALL 913-851-3000 OR EMAIL AT LIGHTING.TECH@FLEX.COM.
MAINTENANCE
LINEAR STRP FIXTURES SHOULD BE DRY DUSTED PERIODICALLY. THE FROSTED LENS CAN BE CLEANED WITH DAMP OR DRY CLOTH. NO SPECIAL CLEANER REQUIRED.
TROUBLESHOOTING
TURN ELECTRICITY OFF AT THE MAIN CIRCUIT BREAKER, PANELBOARD, FUSE BOX OR DISCONNECT. DO NOT ATTEMPT TO TROUBLESHOOT WITH THE POWER ON.
ISSUE 1 - LIGHT DOES NOT COME ON
1.
VERIFY THAT POWER IS BEING DELIVERED TO THE FIXTURE. CHECK ALL UPSTREAM CIRCUIT BREAKERS, FUSES AND DISCONNECTS TO ENSURE THEY ARE ON AND IN PROPER
WORKING ORDER.
2.
CONFIRM ALL ELECTRICAL CONNECTIONS ARE COMPLETE AND CONTINUOUS.
3.
IF THE ISSUE REMAINS UNRESOLVED, CONTACT FLEX LIGHTING SOLUTIONS.
ISSUE 2 - ONE OR MORE LEDS ARE OUT WHILE OTHERS REMAIN ON
1.
DETERMINE IF REPLACEMENT IS DESIRED. AFTER ONE OR MORE LEDS FAILS, THE FIXTURE MAY CONTINUE TO OPERATE NORMALLY, ALTHOUGH WITH A REDUCED LUMEN OUTPUT.
2.
IF REPLACEMENT FIXTURE IS DESIRED, CONTACT FLEX LIGHTING SOLUTIONS.
WARRANTY SUPPORT
PHONE: +1 913-851-3000
EMAIL: LIGHTING.TECH@FLEX.COM
FLEXLIGHTINGSOLUTIONS.COM
WARNING
:
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
RISQUES INHÉRENTS
CAUTION - RISK OF ELECTRIC SHOCK
•
WARNING -
LIGHTING.TECH@FLEX.COM
•
SUITABLE FOR DAMP LOCATIONS.
CONVIENT AUX EMPLACEMENTS HUMIDES.
•
SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 45 °C.
PEUT ÊTRE UTILISÉ À UNE TEMPÉRATURE AMBIANTE N'EXCÉDANT PAS
45°C.
MODELS USING THROUGH WIRE (LNK) AND/OR EMERGENCY BACK-UP -
SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 40 °C.
MODÈLES UTILISANT UN FIL DE SUSPENSION (LNK) ET / OU DE
SAUVEGARDE D'URGENCE - PEUT ÊTRE UTILISÉ À UNE TEMPÉRATURE
AMBIANTE N'EXCÉDANT PAS 40°C.
•
USE INDOORS ONLY.
•
TURN POWER OFF BEFORE SERVICING -- SEE INSTRUCTIONS.
•
PROPERLY GROUND FIXTURE.
•
ENSURE NO BARE WIRES ARE EXPOSED OUTSIDE THE ELECTRICAL
CONNECTIONS.
•
TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING
TO EDGES OR OTHER SHARP OBJECTS.
•
ONLY THOSE OPEN HOLES INDICATED IN THE PHOTOGRAPHS ANDOR
DRAWINGS MAY BE MADE OR ALTERED AS A RESULT OF KIT
INSTALLATION. DO NOT LEAVE ANY OTHER OPEN HOLES IN AN
ENCLOSURE OF WIRING OR ELECTRICAL COMPONENTS.
SEULS LES OUVERTURES INDIQUÉES DANS LES PHOTOS ET/OU LES
DESSINS PEUVENT ÊTRE FAITS OU MODIFIÉS À LA SUITE DE
L'INSTALLATION DU NÉCESSAIRE. IL EST INTERDIT DE LAISSER D'AUTRES
OUVERTURES DANS UN BOÎTIER DE CÂBLAGE OU DE COMPOSANTS
ÉLECTRIQUES.
888-799-5002 option 3 or 913-851-3000 option 3
LS1 SERIES
11-27-18
Advertisement
