Advertisement
INSTALLATION INSTRUCTIONS
IMPORTANT: READ ALL INSTRUCTIONS THOROUGHLY AND CAREFULLY PRIOR TO INSTALLATION OF LINEAR
SERIES FIXTURES AND RETAIN FOR FUTURE REFERENCE.
•
A WIRE HARNESS ELECTRICALLY CONNECTS EACH SECTION VIA QUICK CONNECTORS.
•
EACH CONNECTOR IS KEYED, IT WILL ONLY FIT ONE WAY.
•
EACH FIXTURE HAS A "JUMPER" ON ONE END OF THE WIRING HARNESS. IT IS FACTORY INSTALLED.
•
THE "JUMPER" MUST BE REMOVED FROM THE END OF ONE FIXTURE BEFORE THE NEXT FIXTURE IS CONNECTED. DISPOSE OF PROPERLY.
•
THE "JUMPER" MUST REMIAN CONNECTED TO THE WIRING HARNESS ON ONE END OF THE FIXTURE RUN.
•
MAX 15 LINKED FIXTURES PER POWER DROP.
•
CONNECT EACH SECTION TO THE OTHER USING THE QUICK CONNECTORS. PLUG QUICK DISCONNECT FROM ONE SECTION INTO QUICK DISCONNECT ON
THE NEXT SECTION. REPEAT UNTIL ALL FIXTURES ARE CONNECTED. REMEMBER THE "JUMPER" MUST REMAIN CONNECTED TO THE WIRING HARNESS
ON ONE END OF THE FIXTURE RUN.
•
THE LED LIGHT COVER NEED NOT BE REMOVED FOR INSTALLATION OF EACH SUBSEQUENT LNK FIXTURE.
11. TURN ON ELECTRICITY AT THE CIRCUIT BREAKER, PANELBOARD, OR FUSE BOX.
12. REMOVE PLASTIC FILM FROM LENS.
13. TURN ON ELECTRICITY AT THE CIRCUIT BREAKER, PANELBOARD, OR FUSE BOX.
LNKING FIXTURES WITH OCC/CTRL OPTIONAL ACCESSORIES (LNK):
THE OCC/CTRL-LNK ACCESSORIES MAY BE INSTALLED ANYWHERE IN THE RUN OF LINKING FIXTURES.
THE OCC/CTRL-LNK ACCESSORIES WILL CONTROL THE LIGHTS IN THE ENTIRE RUN IN WHICH IT IS CONNECTED. UNLESS THE SENSOR STOP (LS-SNSRSTOP)
ACCCESSORY IS USED.
ALL "JUMPERS" MUST BE REMOVED FROM ALL LNK FIXTURES WHEN USING AN OCC/CTRL-LNK ACCESSORY. DISPOSE OF PROPERLY.
1.
WIRE LNK AS ABOVE. See LINKING FIXTURES (LNK):
2.
LINKING SECTIONS TOGETHER:
•
THE LED LIGHT COVER NEED NOT BE REMOVED FOR INSTALLATION OF THE ACCESSORY OCC/CTRL.
•
EACH OCC/CTRL-LNK ACCESSORY COMES WITH THE MECHANICAL JOINING PIECE (LS-MJP) INSTALLED ON ONE END AND AN END CAP ON THE OTHER.
•
A WIRE HARNESS ELECTRICALLY CONNECTS EACH ACCESSORY TO THE FIXTURE SECTION VIA QUICK CONNECTOR(S).
•
EACH CONNECTOR IS KEYED, IT WILL ONLY FIT ONE WAY.
•
EACH FIXTURE HAS A "JUMPER" ON ONE END OF THE WIRING HARNESS. IT IS FACTORY INSTALLED.
•
ALL "JUMPERS" MUST BE REMOVED FROM ALL LNK FIXTURES WHEN USING AN OCC/CTRL-LNK ACCESSORY. DISPOSE OF PROPERLY.
•
EITHER THE END CAP OR THE MECHANICAL JOINING PIECE (LA-MJP) INCLUDED ON THE OCC/CTRL ACCESSORY WILL BE DISPOSED OF UPON INSTALLATION,
DEPENDING ON CONFIGURATION. DISPOSE OF PROPERLY.
3.
REMOVE ENDCAP OR MECHANICAL JOINING PIECE (LS-MJP) FROM THE END OF FIXTURE YOU WISH TO JOIN TO THE ACCESSORY. REMOVE THE SCREWS AND
ALSO DEPRESS THE TABS HOLDING IN THE END CAP. DISPOSE OF PROPERLY.
4.
MAKE FINAL ELECTRICAL CONNECTIONS BY CONNECTING EACH SECTION TO THE OTHER USING THE QUICK CONNECTORS.
•
INSERT THE ACCESSORY OCC/CTRL INTO THE END OF THE FIXTURE.
•
REPEAT UNTIL ALL FIXTURES ARE CONNECTED.
5.
TURN ON ELECTRICITY AT THE CIRCUIT BREAKER, PANELBOARD, OR FUSE BOX.
LINKING FIXTURES (LNK) WITH SENSOR STOP FEATURE (SNSRSTOP):
•
SENSOR STOP (LS-SNSRSTOP) IS A WIRE HARNESS ELECTRICALLY CONNECTS EACH ACCESSORY TO THE FIXTURE SECTION VIA QUICK CONNECTOR(S).
•
EACH SENSOR STOP (LS-SNSRSTOP) CONNECTOR IS KEYED, IT WILL ONLY FIT ONE WAY.
THE SENSOR STOP (LS-SNSRSTOP) ALLOWS POWER TO GO THROUGH, NOT THE CONTROL SIGNAL FROM THE OCC/CTRL-LNK ACCESSORY.
THE SENSOR STOP FEATURE (LS-SNSRSTOP) ALLOWS CONTROL TO BE SPLIT AMONG LINKED (LNK) FIXTURES CONNECTED IN A CONTINUOUS RUN. SOME MAY BE
CONTROLLED BY THE OCC/CTRL-LNK ACCESSORY WHILE THE OTHERS ARE NOT, STILL ALLOWING POWER TO BE SENT TO THE OTHER FIXTURES.
EXAMPLE: THERE IS A 10 FIXTURE RUN DOWN AN AISLE, AND YOU WANT THE FIRST FIVE FIXTURES TO BE ON THE ALL THE TIME, BUT HE LAST FIVE TO BE
CONTROLLED BY AN OCCUPANCY SNESOR PLACED IN THE MIDDLE OF THE ROW.
MULTIPLE LS-OCC##-LNK ACCESSORIES MAY BE USED IN A SINGLE CONTINUOUS RUN. WHEN ANY SENSOR IS TRIGGERED, THE ENTIRE ROW WILL BE CONTROLLED.
CONTROLLED FIXTURES MUST BE IN SEQUENCE WITH THE OCCDIM##-LNK OR LS-CTRL-LNK ACCESSORY IN INSTALLATION. ONLY ONE SENSOR PER ROW PERMITTED.
1.
WIRE LNK AS ABOVE. SEE LNKING FIXTURES WITH OCC/CTRL OPTIONAL ACCESSORIES (LNK):
2.
DURING THE INSTALLATION PLACE THE SENSOR STOP ACCESSORY (SNSRSTOP) AT THE LAST FIXTURE YOU WANT TO CONTROL.
•
PLUG SENSOR STOP (LS-SNSRSTOP) QUICK DISCONNECT FROM ONE SECTION INTO QUICK DISCONNECT ON THE NEXT SECTION.
•
CONTINUE INSTALLING FIXTURES UNTIL COMPLETE.
3.
TURN ON ELECTRICITY AT THE CIRCUIT BREAKER, PANELBOARD, OR FUSE BOX.
FLEXLIGHTINGSOLUTIONS.COM
SENSOR STOP
LIGHTING.TECH@FLEX.COM
888-799-5002 option 3 or 913-851-3000 option 3
LS1 SERIES
JUMPER
11-27-18
Advertisement
