Subscribe to Our Youtube Channel
Related Manuals for EINHELL BT-FW 100
Summary of Contents for EINHELL BT-FW 100
- Page 1 Original operating instructions Flux Cored Welding Set Art.-Nr.: 15.752.20 I.-Nr.: 11022 BT-FW...
- Page 3 k, l, m...
-
Page 7: Table Of Contents
Table of contents: Page 1. Safety regulations 2. Layout and items supplied 3. Intended use 4. Technical data 5. Before starting the equipment 6. Operation 7. Cleaning, maintenance and ordering of spare parts 8. Disposal and recycling 9. Troubleshooting 10. Key to symbols... -
Page 8: Safety Regulations
supplied safety shield. Wear gloves and dry safety Important! clothing that are not contaminated by any oil or When using the equipment, a few safety precautions grease to ensure that your skin is not exposed to must be observed to avoid injuries and damage. ultraviolet radiation from the arc. - Page 9 welding. These offer protection from electric sockets must comply with the relevant shocks (idling voltage in the welding circuit), regulations (VDE 0100). To comply with these harmful radiation (Heat and UV radiation) and regulations, only fuses or circuit breakers from glowing metal and slag spatter. suitable for the cross-section of the cables may 6.
-
Page 10: Layout And Items Supplied
protected. Unauthorized persons are to be kept 3. Intended use away from the welding work. 2. The walls in the immediate vicinity of stationary The flux cored welding set is designed for self- workplaces should not have a light color or a shielding flux cored welding using suitable wire. -
Page 11: Before Starting The Equipment
5. Before starting the equipment 5.3 Fitting the wire spool (Fig. 1, 2, 3, 14 – 22) The wire spool is not supplied. 5.1 Assembly (Fig. 7-13) 5.3.1 Wire types Various welding wires are required for different 5.1.1 Fitting the carrying strap (1) applications. -
Page 12: Operation
two guide grooves. Turn the feed roller (G) over 6. Operation if necessary or replace it. (Fig. 19). Position the feed roller holder (F) again and 6.1 Setting secure it. Since the welding set must be set to suit the specific Remove the gas nozzle (Fig. -
Page 13: Cleaning, Maintenance And Ordering Of Spare Parts
When the arc is burning, the welding set will feed 7.3 Ordering replacement parts: wire into the weld pool. When the weld nugget is Please provide the following information on all orders large enough, move the burner slowly along the for spare parts: required edge. -
Page 14: Troubleshooting
9. Troubleshooting Fault Cause Remedy Feed roller does not turn Power supply not connected Check connection Wire feed controller set to 0 Check setting Feed roller turns, but does not feed Incorrect roller pressure (see 5.3.3) Check setting any wire Roller brake set too firmly (see Check setting 5.3.3) -
Page 15: Key To Symbols
10. Key to symbols EN 60974-1 European standard for Do not store or use the arc welding sets and equipment in wet or welding power supplies damp conditions or in with limited on time the rain. Standardized operating Single-phase mains voltage connection Mains voltage... - Page 16 t For EU countries only Never place any electric tools in your household refuse. To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its implementation in national laws, old electric tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g.
- Page 17 The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of ISC GmbH. Technical changes subject to change...
- Page 19 t GUARANTEE CERTIFICATE Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card.
- Page 20 EH 03/2013 (01)
Need help?
Do you have a question about the BT-FW 100 and is the answer not in the manual?
Questions and answers