Related Manuals for EINHELL BT-EW 160
Summary of Contents for EINHELL BT-EW 160
- Page 1 Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 1 Operating Instructions Welding Set Art.-Nr.: 15.460.41 I.-Nr.: 01018 BT-EW...
- Page 2 Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 2...
- Page 3 Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 3...
- Page 4 Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 4...
-
Page 5: Items Supplied
Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 5 Repairs and/or maintenance work may only be Important! carried out by qualified personnel. When using the equipment, a few safety precautions Use only the power cables and welding cables must be observed to avoid injuries and damage. supplied. -
Page 6: Proper Use
Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 6 Important! dazzling and burns, the arc also gives off If the supply mains and circuits are overloaded, other UV radiation. Without proper protection, this consumers may suffer interference during the invisible ultraviolet radiation causes very painful welding work. -
Page 7: Symbols And Technical Data
Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 7 conductive materials to insulate your body against 4. SYMBOLS AND TECHNICAL DATA the floor, walls, conductive parts of the machine and the like. EN 60974-6 European standard for arc welding sets and welding power supplies with If you use small welding transformers for welding in limited on time (Part 6). -
Page 8: Welding Preparations
Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 8 5. Assembly Instructions 7. Welding preparations See Figure 5-12. Connect the earth terminal (-) (2) direct to the part to be welded or to the support on which the part is resting. Ensure that the earth terminal (-) is in direct 6. -
Page 9: Overheating Guard
Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 9 Important! Always use tongs to remove spent electrodes and to move parts that you have just welded. Please note that the electrode holder (1) must always be put down so that it is insulated after you have completed the welding work. - Page 10 Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 10 Service Contact: Cerathai Co. Ltd. 2332, 2334, 2336 Ladphrao 114 Ladphrao Road, Wangthong Lang Bangkok 10310 The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only Technical changes subject to change with the express consent of ISC GmbH.
- Page 11 Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 11...
- Page 12 Anleitung_BT_EW_160_SPK7:_ 09.07.2008 15:11 Uhr Seite 12 EH 07/2008 (01)