Table of Contents
Advertisement
Quick Links
Installation and Operation Instructions
f i r e - p a r t s . c o m
Immediately call your gas supplier from a neighbor's phone,
If you can't reach your gas supplier, call the fire department.
vapors and liquids in the vicinity of this or any other appliance
maintenance can cause injury, property damage or loss of life
READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
AGDVT-38
ARCHGARD INDUSTRIES LTD.
7116 Beatty Dr., Mission BC, V2V 6B4
Marquis AGDVT-38D Natural Gas
Marquis AGDVT-38DP Propane
Direct Vent Gas Fireplace
Decorative Gas Appliance
Not a source of heat. Not for use with solid fuel.
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switches.
Do not use any phone in your building.
follow the gas supplier's instructions.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable
Improper installation, adjustment, alteration, service or
Canada
WARNING:
for:
23/10/97
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Archgard Marquis AGDVT-38D
Summary of Contents for Archgard Marquis AGDVT-38D
- Page 1 ARCHGARD INDUSTRIES LTD. 7116 Beatty Dr., Mission BC, V2V 6B4 Canada Installation and Operation Instructions for: Marquis AGDVT-38D Natural Gas Marquis AGDVT-38DP Propane Direct Vent Gas Fireplace Decorative Gas Appliance Not a source of heat. Not for use with solid fuel.
-
Page 2: Table Of Contents
TABLE OF CONTENTS GENERAL INFORMATION SPECIFICATIONS CAUTION LOCATING YOUR FIREPLACE FRAMING DIMENSIONS CLEARANCE TO COMBUSTIBLES VENT LOCATION CAUTION GENERAL VENTING SPECIFICATIONS f i r e - p a r t s . c o m INSTALLATION INSTRUCTIONS FAN INSTALLATION OPERATION INSTRUCTIONS LIGHTING INSTRUCTIONS TURNING OFF GAS APPLIANCE MAINTENANCE AND CLEANING... -
Page 3: General Information
GENERAL INFORMATION CAUTION Due to high temperatures, the appliance should be The AGDVT-38D & AGDVT-38DP are Natural Gas / located out of traffic and away from furniture and Propane zero-clearance direct vent type fireplaces. They draperies. have been tested to CGA 2.22/Interim requirement #41, CGA I.R. -
Page 4: Locating Your Fireplace
LOCATING YOUR FIREPLACE This fireplace may be installed in any location that is free of plumbing, electrical wiring and heating or air conditioning ducts. Select a location that is accessible for venting. (See terminal locations) DIAGRAM 2 f i r e - p a r t s . c o m DIAGRAM 3 FRAMING DIMENSIONS For cold climate installation, it is recommended that the... -
Page 5: Clearance To Combustibles
VENT LOCATION CLEARANCE TO COMBUSTIBLES Once you have established the fireplace location using Back = 0” (0mm) to standoffs the Allowed Terminal Locations, then you can frame in Left side = 0” (0mm) to standoffs the vent outlet as per diagram. Right side = 0”... -
Page 6: Caution
8” rigid galvanized SPECIFICATIONS outer vent. Use Marquis AGDVT-38D or AGDVT-38DP vent components only. f i r e - p a r t s . c o m All vent pipes must maintain a minimum of 1” clearance to combustibles on sides and bottom, and 3”... - Page 7 rise. Max. of 5 -90 elbows (one 90 elbow = two slip over flex and secure to provide clearance between elbows) inside flue pipe and outside vent pipe. Note: Use 8” dia. rigid outer vent pipe above the roof line. GENERAL VENTING SPECIFICATIONS The AGDVT-38 was designed for various installation (CON’T)
-
Page 8: Installation Instructions
Mill-Pac on flex pipe and 8” collar to seal. Secure termination to outside wall and seal around termination kit wall plate. See Diagram 2. INSTALLATION INSTRUCTIONS 12) Position 4 logs on the grate inside the firebox as shown (logs are notched for position). -
Page 9: Fan Installation
OPERATION INSTRUCTIONS FAN INSTALLATION For your safety read before lighting This fan kit (FK-38) is listed for use with Archgard WARNING: If you do not follow these instructions AGDVT 38 fireplace. Check with your local building exactly, a fire or explosion may result code before installation to ensure compliance. -
Page 10: Turning Off Gas Appliance
For correct flame pattern, first remove the glass front. Use a 1/4” hex head screw driver and turn the cover sleeve to the proper opening. The flame should burn blue and yellow as diagram shows. Tighten the hex 5) Wait five (5) minutes to clear out any gas. If you head screw and then put the glass front back on. -
Page 11: Maintenance And Cleaning
If the glass needs to be replaced, this should be Brass Louvre Kit BRLK-38 done by a qualified service person. Black Square Door BLSD-38 Face Assembly F-38 Note: If the glass is broken, carefully remove as outlined below and take it to an authorized Archgard dealer or the manufacturer. -
Page 12: Allowed Termination Locations
ALLOWED TERMINATION LOCATIONS f i r e - p a r t s . c o m... -
Page 13: Notes
NOTES f i r e - p a r t s . c o m... - Page 14 f i r e - p a r t s . c o m MADE IN CANADA...
Need help?
Do you have a question about the Marquis AGDVT-38D and is the answer not in the manual?
Questions and answers