Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for baracuda gotcha EP34 Series
Summary of Contents for baracuda gotcha EP34 Series
- Page 1 EP34-- EP35-- Owner's Manual...
-
Page 2: Table Of Contents
If the original dealer does not perform warranty service, please visit www.baracuda.com.au to locate an independent service company near you. If you are unable to locate a service company,please call our Baracuda Customer Service at 1300 784 423. -
Page 3: Section 1. Important Safety Instructions
• Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge trimmers and other equipment. • To reduce the risk of electrical shock, do not use the robotic cleaner or control box if the cord is worn or damaged. Contact Baracuda Customer care Service 1300 784 423 immediately for proper servicing and replacement of the damaged cord. -
Page 4: Section 2. Getting Started
(WxDxH) during transport. Weight of Cleaner 7 kg • If there are missing parts or damage, Filtration All-purpose filter canister. (200 contact Baracuda Technical Support: micron) 1300 784 423 Power Supply IP45 Robotic Cleaner IPX8 Cleaner Control Unit This cleaner is a double-insulated product. A double-... -
Page 5: Connecting The Floating Cable To The Control Box
Section 2. Getting Started Connecting the Floating Cable to the Control Box WARNING Failure to comply with the following warnings Align: Key with can result in permanent injury, electrocution or Notch drowning. PREVENT ELECTRICAL SHOCK • Keep the control unit at least five 3.5m from the edge of the pool. -
Page 6: Section 3. Operation
• Baracuda recommends only three cleaning cycles per week. The Baracuda robotic cleaner includes a safety feature that automatically stops the cleaner if it is powered on but not submerged in water. For pools equipped... -
Page 7: Stopping The Cleaner And Removing From The Pool
Section 3. Operation Stopping the Cleaner Rinsing the Cleaner and Removing from the Pool Rinse the cleaner after every cleaning cycle. Use slightly soapy clean water, then rinse generously Press Start/Stop button on control unit to with clean water. Do not use solvents such as interrupt operation. -
Page 8: Storing The Cleaner
Section 3. Operation Grasp the handle and lift up to remove the filter canister (Figure 8). Figure 10. Rinse the Filter Canister Let the lid and filter canister dry. Replace lid on the canister and then replace canister back into the cleaner body. Plug the power cord back into the control unit and store the cleaner out of direct sunlight for next use. -
Page 9: Section 4. Maintenance
To maintain cleaner performance at its best you need to replace the brush as soon as one of the wear indicators has been reached (even if the blade wear is not even). Baracuda recommends that you replace the brush every two (2) years. H0670800... -
Page 10: Replacing The Track
1 Flash Unplug the floating cable from LED flashes once the control unit and reconnect. with one second If the problem persists, contact interval. Baracuda Customer Service at 1300 784 423 2 Flashes Turn cleaner wheels to ensure LED flashes twice they are not jammed. with one second Check brushes for debris. -
Page 11: General Troubleshooting
Unit is turned OFF. Turn the tracks then disconnect the control unit and wait at least 20 secocds before reconnecting. If the problem persists, contact Baracuda Customer Service at 1300 784 423 Cable is tangling in the Too much cable length in the water. - Page 12 (see Warranty Card inside the pack). Happy Swimming! For more information visit www.baracuda.com.au or call 1300 784 423 Baracuda is a registered trademark of Zodiac Group Australia Pty Ltd ABN 87 002 641 965 219 Woodpark Rd, Smithfield, NSW 2164 Australia Tel: 1300 784 423 www.baracuda.com.au...
Need help?
Do you have a question about the gotcha EP34 Series and is the answer not in the manual?
Questions and answers
Where can I buy new tracks and brushes for a Gotcha pool cleaner