Related Manuals for REMKO RXD 260
Summary of Contents for REMKO RXD 260
- Page 1 REMKO RXD RXD 260, RXD 350, RXD 520, RXD 680, RXD 1200 Ceiling cassettes Operation · Technology · Spare parts Issue GB – T10...
-
Page 3: Table Of Contents
/ operation of the equipment! These instructions are part of the equipment and must always be kept in the vicinity of the installation or on the equipment Made by REMKO Subject to modifications; No liability accepted for errors or misprints! -
Page 4: Safety Notes
REMKO as this may the equipment was purchased the equipment. cause malfunctions. and commissioned and returned these papers to REMKO GmbH &... -
Page 5: Transport And Packaging
• RXS 261H system and condensation pan. • RXS 351H The indoor unit can be combined • RXS 521H with REMKO outdoor components • RXS 681H that provide sufficient cooling • RXS 1200H output. The outdoor component is Cooling controlled via the regulation of the... -
Page 6: Operation
REMKO RXD Operation The indoor unit is easy to operate Manual operation Infrared remote control using an infrared remote control. This is supplied as standard. The The indoor units can be started The infrared remote control indoor unit beeps to acknowledge manually. - Page 7 Buttons on the remote control "SWING" Button Buttons on the remote control This button switches on the "POWER" button oscillating fins to provide Press this button to start the improved air distribution in the unit. room. It can also be used to lock the fins.
- Page 8 REMKO RXD Button functions A symbol is shown on the display to indicate that the settings are being transferred. Press the POWER button to activate/deactivate the indoor unit. The POWER Button programmed settings and adjustment values before the unit was turned off will appear in the display.
-
Page 9: Operation
Press the MODE button to change to another mode. A total of 5 modes MODE Button are available: 1. Automatic Automatic selection of cooling or heating operation 2. Cooling Cooling mode, predominantly used during summer 3. Dehumidification Dehumidifying mode, used in summer or winter 4. - Page 10 REMKO RXD Press the MODE button once or repeatedly to switch to dehumidifying Mode DRy mode. Use this mode to dehumidify the room in an unregulated fashion. After pressing the DRY button, select the desired temperature and fin position. It is not possible to set the fan speed. The fan is switched off at certain intervals to lower the temperature at the cooling battery.
- Page 11 The TIME-ON/-OFF buttons are used to program the switch-on/off time, TIME Buttons the TIME-SET button to set the time. Switch-on time Press the TIME-ON or TIME-OFF button to activate the timer. The clock display then disappears. The timer symbol for the switch-on/off time will flash.
-
Page 12: Shutdown
4. Switch the supply voltage back Contact REMKO GmbH & Co. KG or your contract partner for a list of specialist companies near you. Type of task Checks / maintenance / inspection •... - Page 13 Air filter for indoor unit 9. Switch the supply voltage back Guard on cover Clean the air filter at intervals of no more than 2 weeks. Reduce this 10. Switch the unit back on. interval if the air is especially dirty. Cleaning the filter Cleaning the condensation pump...
-
Page 14: Troubleshooting And Customer Service
REMKO RXD Troubleshooting and customer service The equipment and components are manufactured using state-of-the-art production methods and tested several times to verify their correct function. If malfunctions should occur, please check the functions as detailed in the list below. For installations with an indoor unit and outdoor component, refer to the chapter "Troubleshooting and customer service"... -
Page 15: Installation Instructions For Qualified Personnel
Error and operational malfunction indicated by flashing code Cause Required action (red) (yellow) (green) Fan at max. speed Normal operating condition Fan at medium speed Normal operating condition Fan at low speed Normal operating condition flashes Heating mode: Warm-up phase Wait approx. -
Page 16: Installation
REMKO RXD Service openings should be Installation material Selection of the installation ■ provided in the suspended location ceiling to allow maintenance The indoor unit is fastened using The indoor unit is designed access to the control box. 4 threaded rods (provided by the for horizontal mounting in customer) at the side mounts. - Page 17 The refrigerant pipes are unit and the underside of the cover. connected to the RXD 260-520 on fastening surface. Connect the angled side of the unit and on the refrigerant pipes, electrical the RXD 680-1200 in the middle cables and condensation pipe of the longer side.
- Page 18 REMKO RXD Connections to adjacent room Connections to adjacent room and fresh air intake and fresh air intake Fresh air intake The indoor unit has been designed to allow the cooling of a second Connection to room as well as the intake of fresh adjacent room air.
- Page 19 Connection to adjacent room Observe the regional The air at the outdoor air intake ■ ■ regulations concerning air should be sucked in through The indoor unit can also be used treatment. a dust filter at a maximum to cool an adjacent room through rate of 2.5 m/s to prevent the a duct system, e.g.
-
Page 20: Condensation Connection
REMKO RXD Condensation connection If the temperature falls below the condensation runs directly The condensation pipe should ■ dew point, condensation will form into a sewer pipe, fit a trap to have a fall of min. 2 %. on the cooling fins during cooling prevent any unpleasant odours. -
Page 21: Electrical Connection Diagram
Make the following electrical Make the connection as follows: connections: 1. Open the control box cover by Connecting the unit removing the fixing screws and 1. Connect the control cable from lifting off the cover (Fig. 12). the outdoor component 2. -
Page 22: Electrical Circuit Diagram
REMKO RXD Electrical circuit diagram RXD 260 - 520 Air circulation sensor Vaporiser sensor Sensor Swing motor 1-4 Defrost Wired remote control Jumper Jumper Display Transformer Condensation float switch Condensation pump motor RXD 680 - 1200 Air circulation sensor Vaporiser sensor... -
Page 23: Commissioning
Unit dimensions RXD 260, RXD 350 RXD 520 RXD 260 to 520 RXD 680, RXD 1200 1220 1110 All values in mm We reserve the right to modify the dimensions and constructional design as part of the ongoing technical development process. -
Page 24: Product Illustration
REMKO RXD Exploded view RXD 260 to 520 We reserve the right to modify the dimensions and constructional design as part of the ongoing Spare parts list technical development process. Designation RXD 260 RXD 350 RXD 520 Air inlet guard... - Page 25 Exploded view RXD 680 / RXD 1200 We reserve the right to modify the dimensions and constructional design as part of the ongoing technical development process. Spare parts list Designation RXD 680 RXD 1200 Air inlet guard 1106678 1106678 Air filter 1106665 1106665 Cover...
-
Page 26: Technical Data
REMKO RXD Technical data Series RXD 260 RXD 350 RXD 520 RXD 680 RXD 1200 Operating mode Ceiling cassette for combined cooling/heating Nominal cooling output 2,69 3,59 5,27 6,84 12,48 Nominal heating output 2,96 4,24 6,31 7,72 13,23 Energy efficiency class, cooling... - Page 27 Notes...
- Page 28 REMKO, a partner who helps solve problems. Sales REMKO not only has a well- established sales network at home and abroad, it also employs highly trained sales specialists. REMKO Our field staff are more...