Related Manuals for REMKO RXS H Series
Summary of Contents for REMKO RXS H Series
- Page 1 REMKO RXS H RXS 261 H, RXS 351 H, RXS 521 H, RXS 681 H, RXS 1200 H Combined - outdoor components Operation · Technology · Spare parts Issue GB - W06...
-
Page 3: Table Of Contents
These instructions are part of the equipment and must always be kept in the vicinity of the installation or on the equipment This operating manual is a translation of the German original, Version W-06 Made by REMKO Subject to modifications; No liability accepted for errors or misprints! -
Page 4: Safety Notes
REMKO as this may maintenance work or cleaning the equipment was purchased and cause malfunctions. the equipment. commissioned and returned the... -
Page 5: Intended Use
The unit can be installed outdoors The outdoor component can be Winter controllers, floor brackets, or indoors. The latter requires the combined with REMKO indoor wall brackets and refrigerant pipes fulfilment of certain conditions. units that provide sufficient are available as accessories. -
Page 6: Combinations
REMKO RXS H Combinations Cooling / heating 261H 351H 521H 681H 1200H • RXW 261 • RXW 351 • RXW 521 • RXW 681 • RXD 260 • RXD 350 • RXD 520 • RXD 680 • RXD 1200 •... -
Page 7: Operation
• • Check function of compressor collection points. • • Check fan is functioning correctly Contact REMKO GmbH & Co. KG • • Dirt on liquefier or your contract partner for a list of specialist companies near you. • •... -
Page 8: Troubleshooting And Customer Service
REMKO RXS H Troubleshooting and customer service The unit has been manufactured using state-of-the-art production methods and tested several times to ensure its correct function. If malfunctions should occur, please check the unit as detailed in the list below. For installations with an indoor unit and outdoor component, refer to the chapter "Troubleshooting and customer service"... -
Page 9: Installation Instructions For Qualified Personnel
Installation instructions for qualified personnel Important points prior to Only open the stop valves Wall openings ■ installation for the refrigerant pipes after installation has been fully The wall breakthrough must ■ Observe the manuals for completed. have a diameter of min. ■... - Page 10 REMKO RXS H Selecting the installation Wind Snow location If the unit is being installed in The unit should be wall-mounted The outdoor component is windy areas, ensure that the in areas of heavy snowfall. designed for horizontal and warm outlet air discharges in the...
-
Page 11: Installation
Installation Ensure a continuous and unobstructed air flow from outside, ■ NOTE preferably using sufficiently large air intakes. Installation should only be performed by authorised Comply with any regulations and conditions affecting the statics of ■ specialists. the building. If necessary, fit acoustic installation. The following instructions describe the installation of the refrigerant circuit and the assembly Of... - Page 12 REMKO RXS H 8. Remove the factory-fitted 14. Fit appropriate heat insulation Supplementary information to both installed refrigerant protective caps and union nuts for installation lines, including the connectors. on the stop valve connections. These should be used during When combining the outdoor ■...
-
Page 13: Tightness Check
Tightness check Condensation Electrical connection connection A mains supply cable and six-core Once all the connections have If the temperature falls below control cable must be laid to the been established, the pressure the dew point, condensation will outdoor component and indoor gauge station is attached as form on the cooling fins in heating unit respectively. -
Page 14: Electrical Connection Diagram
REMKO RXS H Proceed as follows to connect the 4. Feed both cables through the Connecting the outdoor component cable: edge protection rings on the fixed connection panel. 1. Remove the cover from the unit. 5. Terminate the cables as shown on the electrical connection 2. -
Page 15: Electrical Circuit Diagram
Electrical circuit diagram Before Commissioning RXS 261H-681H After the tightness check has been successfully completed, Liquefier fan connect the vacuum pump via the pressure gauge station to the valve connections on the Reverse flow valve outdoor component (see chapter "Tightness check") Compressor Connect the outdoor component contactor... -
Page 16: Add Refrigerant
REMKO RXS H Commissioning Add refrigerant CAUTION NOTE Note that the employed Commissioning should only be refrigerant is always filled in performed by specially trained liquid form! personnel and documented after the certificate has been NOTE issued. CAUTION Check the overheating to... - Page 17 Functional test of the indoor 5. Set the target temperature Final tasks ■ unit and all program sequences. on the indoor unit using the remote control. This should be Use the remote control to set ■ Check of the surface set to a value lower than the the target temperature to the ■...
-
Page 18: Unit Dimensions
REMKO RXS H Unit dimensions RXS 261H / RXS 351H RXS 521H RXS 681H RXS 1200H All values in mm We reserve the right to modify the dimensions and constructional design as part of the ongoing technical development process. Technical data... -
Page 19: Product Illustration
Product illustration Spare parts list Designation RXS 261H RXS 351H RXS 521H RXS 681H RXS 1200H From number of series 810W6001-... 811W6001-... 812W6001-... 813W6001-... 814W5008-6999 Front panel 1107800 1107813 1107826 1107838 1107850 Fan blade, liquefier 1107864 1107864 1107864 1107839 1107851 Fan motor, liquefier 1107865 1107865... - Page 20 REMKO, a partner who helps solve problems. Sales REMKO not only has a well- established sales network at home and abroad, it also employs highly trained sales specialists. REMKO Our field staff are more...