Related Manuals for REMKO RXW 261
Summary of Contents for REMKO RXW 261
- Page 1 REMKO RXW RXW 261, RXW 351, RXW 521, RXW 681 Wall units Operation · Technology · Spare parts Issue GB – U01 Downloaded from AC-Manual.com Manuals...
- Page 2 Downloaded from AC-Manual.com Manuals...
-
Page 3: Table Of Contents
/ operation of the equipment! These instructions are part of the equipment and must always be kept in the vicinity of the installation or on the equipment Made by REMKO Subject to modifications; No liability accepted for errors or misprints! Downloaded from AC-Manual.com Manuals... -
Page 4: Safety Notes
REMKO as this may the equipment. commissioned and returned the cause malfunctions. completed card to REMKO GmbH The equipment or components &... -
Page 5: Transport And Packaging
RXW 351 RXW 521 RXW 681 • The indoor unit can be combined RXS 261H • RXS 351H with REMKO outdoor components • RXS 521H that provide sufficient cooling • RXS 681H output. The outdoor component is Cooling controlled via the regulation of the indoor unit. -
Page 6: Operation
REMKO RXW Operation The indoor unit is easy to operate Manual operation Infrared remote control using an infrared remote control. The indoor units can be put into The infrared remote control This is supplied as standard. The indoor unit beeps to operation manually. - Page 7 2. Cooling mode "TIMER ON“ Button Buttons on the remote control In this mode, the warm room This button is used to program air is cooled to the desired the automatic turn on time temperature. of the unit within the next 24 hours.
-
Page 8: Button Functions
REMKO RXW Button functions A symbol is shown on the display to indicate that the settings are being transferred. Stand by of remote control The stand by readiness of the remote control is signalled by the blinking dot on the remote control. - Page 9 The time can be programmed by pressing the CLOCK button inside the CLOCK Button battery compartment. “CLOCK“ blinks in the display and the current time is set via the HR. and MIN. button. Pressing the CLOCK button again completes the programming, the display no longer blinks. CLOCK HR/MIN CLOCK...
- Page 10 REMKO RXW In dehumidification mode, the target temperature is set to 24 °C. Due DEHUMIDIFICATION MODE to the low temperature of the refrigerant, the dew point of the air on the condenser is lower. The excess moisture in the air is condensed by the vaporiser, the room is dehumidified.
- Page 11 The oscillating function of the air discharge fins can be adjusted with this SWING Button button. This makes it possible to directly switch between an adjusted position and the oscillating function. The air distribution in the room is improved with the swing function. SWING SWING SWING...
-
Page 12: Operation
REMKO RXW TIMER Buttons ON/OFF The regulation turns the unit on and off daily at the programmed time. During operation, all settings and the timer symbol can be seen on the display. During shut down, the display 0->1 and the Timer symbol can be seen. -
Page 13: Shutdown
Contact REMKO GmbH & Co. KG or your contract partner for a list of specialist companies near you. Type of task Checks / maintenance / inspection •... - Page 14 REMKO RXW Cleaning the housing Cleaning the filter 8. Close the front side as described above but in reverse 1. Disconnect the supply voltage 1. Disconnect the power supply to order. the unit. to the equipment. 9. Switch the supply voltage back 2.
-
Page 15: Troubleshooting And Customer Service
Troubleshooting and customer service The equipment and components are manufactured using state-of-the-art production methods and tested several times to verify their correct function. If malfunctions should occur, please check the functions as detailed in the list below. For installations with an indoor unit and outdoor component, refer to the chapter "Troubleshooting and customer service"... - Page 16 REMKO RXW Fault Possible cause Check Remedial measures Filter is dirty / air inlet / outlet Have the filters been cleaned? Clean the filters opening is blocked by by debris Have there been any Doors and windows open / Close doors and windows /...
-
Page 17: Installation Instructions For Qualified Personnel
Installation instructions for qualified personnel Important points prior to Seal off open refrigerant pipes Minimum clearances ■ installation with suitable caps or adhesive strips to avoid the infiltration Observe the minimum clearances For installation of the entire of moisture and never kink or to allow access for maintenance system, observe the operating compress the refrigerant pipes. -
Page 18: Installation
REMKO RXW Installation Connection of refrigerant NOTE Horizontal alignment pipes Installation should only be performed by authorised The on-site connection of the specialists. refrigerant pipes is made at the rear of the unit. Unit installation If necessary, a reduction or... -
Page 19: Condensation Connection
Condensation connection Electrical connection Due to the dew point shortfall, A protected power supply cable If an optional condensation ■ condensation forms on the and asix-core (RXS) or a four- pump is used in conjunction vaporiser during the cooling core (RXM) control cable should with the unit, it may be operation on the indoor unit. -
Page 20: Electrical Connection Diagram
2. Use the remote control to turn on the unit and select the cooling mode, maximum Electrical circuit diagram fan speed and lowest target temperature. RXW 261 to 681 3. Measure and record all the required values in the commissioning report and Vaporiser Swing motor check the safety functions. -
Page 21: Unit Dimensions
Unit dimensions Functional test for RXW 261 / 351 heating mode (only for RXS...H) 1. Switch the supply voltage on. 2. Use the remote control to switch on the unit and select RXW 521 the heating mode, maximum fan speed and highest target temperature. -
Page 22: Unit Illustration
REMKO RXW Unit illustration RXW 261 to RXW 681 We reserve the right to modify the dimensions and constructional design as part of the ongoing technical development process. Spare parts list RXW 261 RXW 351 RXW 521 RXW 681 Designation... -
Page 23: Technical Data
Technical data Series RXW 261 RXW 351 RXW 521 RXW 681 Operating mode Wall unit for cooling and heating Nominal cooling output 2,69 3,59 5,27 6,84 Nominal heating output 2,96 4,24 6,31 7,72 Energy efficiency class, cooling Energy efficiency ratio EER... - Page 24 REMKO - Our field staff are more than just salesmen: above all, they must advise our clients in the areas of air conditioning and heating technology.