Viega 8351.1 Instructions For Use Manual
  1. Manuals
  2. Brands
  3. Viega Manuals
  4. Plumbing Product
  5. 8351.1
  6. Instructions for use manual

Viega 8351.1 Instructions For Use Manual

Flush plate visign for more 101
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Flush plate Visign for More 101
Instructions for Use
for concealed cistern 2H, concealed cistern 2L, concealed cis-
tern 2C
Model
8351.1
en_INT
Year built:
from 07/2007

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 8351.1 and is the answer not in the manual?

Questions and answers

Related Manuals for Viega 8351.1

Summary of Contents for Viega 8351.1

  • Page 1 Flush plate Visign for More 101 Instructions for Use for concealed cistern 2H, concealed cistern 2L, concealed cis- tern 2C Model Year built: 8351.1 from 07/2007 en_INT...
  • Page 2 Flush plate Visign for More 101 2 from 17...

  • Page 3: Table Of Contents

    Table of contents Table of contents About these instructions for use Target groups Labelling of notes About this translated version Product information Intended use 2.1.1 Areas of use Product description 2.2.1 Overview 2.2.2 Technical data Handling Assembly information 3.1.1 Required material and tools Assembly 3.2.1 Prepare cistern...

  • Page 4: About These Instructions For Use

    This restriction does not extend to possible operating instructions. The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.

  • Page 5: About This Translated Version

    About these instructions for use About this translated version This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e.

  • Page 6: Product Information

    2 Product information Intended use 2.1.1 Areas of use Suitable cisterns The flush plate is intended for the actuation of flushes on Viega con- cealed cisterns. Installation is only possible in the following Viega concealed cisterns: Cistern model 2H Cistern model 2L Ascertain which model is installed before mounting.

  • Page 7: Product Description

    Product information Product description 2.2.1 Overview Fig. 1: Component overview 1 - flush plate 2 - basic panel 3 - threaded bolt 4 - Bowden cable unit 2.2.2 Technical data The product exhibits the following technical data: Flush volume The flush volume for the flushes are: Small flush volume: approx.

  • Page 8: Handling

    Handling 3 Handling Assembly information 3.1.1 Required material and tools Tool The following tools are required for mounting: flat screwdriver knife (cutter) Assembly 3.2.1 Prepare cistern The following work stages and diagrams differ depending on the cistern being used. The relevant steps are marked accordingly.
  • Page 9 Handling Score the revision shaft along the edge of the tiles with a knife. Angle the knife to do this so that the cut is made flush to the surface of the wall. Cut the corners of the revision shaft vertically through to the wall surface.
  • Page 10 Handling INFO! Only for assembly of the flush plate in cistern 2H or on the front of cistern 2L. Press the bow backwards from the mounting of the mechanism. INFO! Only for assembly of the flush plate on the top of cistern Press the bow backwards from the mounting of the mechanism.
  • Page 11 Handling INFO! Only with the cistern 2H. Remove and keep spacer. Remove and dispose of the bow from the drain valve. Flush pipelines (cistern 2H) Requirements: The revision shaft is shortened in such a way that it is flush with the surface.
  • Page 12 Handling Loosen flexible hose on the filling valve (SW 19). Open the corner valve for a few seconds to rinse the pipe. Re-close corner valve. Connect the flexible hose onto the filling valve (SW 19). Open corner valve. Flush plate Visign for More 101 12 from 17...
  • Page 13 Handling Flush pipelines (cistern 2L) Requirements: The revision shaft is shortened in such a way that it is flush with the upper edge of the tiles. Mechanism and bow have been removed. Close corner valve. Loosen flexible hose on the filling valve (SW 19). Open the corner valve for a few seconds to rinse the pipe.

  • Page 14: Mount Flush Actuation

    Handling Connect the flexible hose onto the filling valve. Open corner valve. 3.2.2 Mount flush actuation Mount Bowden cable unit Push the Bowden cable unit onto the drain valve from the left. The Bowden cable unit must be felt to click into place on the drain valve.

  • Page 15: Mounting The Flush Plate

    Handling INFO! Only with the cistern 2H. Insert spacer. 3.2.3 Mounting the flush plate Requirements: The flush actuation has been mounted. Insert the threaded bolts left and right into the holders. The threaded anchors must be positioned to the top and bottom. Insert the threaded bolts so deeply that the upper edge of the threaded bolt sticks out approx.

  • Page 16: Commissioning

    Handling Mount Bowden cable unit onto the rear side of the basic panel. INFO! Observe the colour of the adapter! Screw on basic panel. Mount flush plate. INFO! The figure shows model 8331.1 as an example. Commissioning 3.3.1 Setting the flush Flush plate Visign for More 101 16 from 17...

  • Page 17: Error, Faults And Remedy

    Handling Set the flush volume on the drain valve of the cistern. Small flush volume (above): approx. 3–4 litres Large flush volume (below): approx. 6–9 litres Error, faults and remedy Error Cause Remedy WC does not flush Cistern is not yet completely full Wait until the cistern is sufficiently full No water in cistern, corner valve is...

Table of Contents