Dthernet Connector (Tips And Lan Iorts); Upsb Connector; T Connector; Telay Connector - Lightware HDBaseT HDMI-TPS-RX110AY-Plus User Manual


  
3. Product Overview
3.3.4. Ethernet Connector (TPS and LAN Ports)
The extender provides standard TJ45 connectors for TIPS
N and LAN
ports. Always use high quality Ethernet cable for connecting
transmitters and receivers. Maximum CATx cable distances can be
found in the Maximum Extension Distances
8 1
RJ45 connector for LAN port RJ45 connector for TPS input port
Wiring of TPS and LAN Cables
Lightware recommends the termination of LAN cables on the basis of
T
A/D
A T 568 A or T
A/D
A T 568 B standards.
8
1
Top Bottom
Pin TIA/EIA T568 A Color and name TIA/EIA T568 B Color and name
1 white/green stripe
2 green solid
3 white/orange stripe
4 blue solid
5 white/blue stripe
6 orange solid
7 white/brown stripe
8 brown solid
You can find more information about TIPS interface in the
section.
3.3.5. USB Connector
The extender provides standard USB 2.0 mini B-type connector
for software control purpose.
3.3.6. IR Connector
IR detector and IR emitter can be connected to the receiver with
TRS (Tip, Ring, and Sleeve) connectors. They are also known
as (3,5 mm or approx. 1/8") audio jack, phone jack, phone plug, and
section. mini-jack plug. The pin assignments are the following for the detector
and the emitter:
1 8
Detector – 3-pole TRS
1 Tip
2 Ring
3 Sleeve


NFF:
three-pole TRS plug, then the Ring and the Sleeve are the same
1
signal (Output - ).
You can find more information about
nfrared interface in the
8
IR Interface
Side
3.3.7. RS-232 Connector
The receiver contains a 3-pole Phoenix connector which is used for
white/orange stripe
RS-232 serial connection.
orange solid
white/green stripe
1 2 3
blue solid
white/blue stripe
green solid
white/brown stripe
Compatible Plug Type
Phoenix
brown solid
You can find more information about TPS-232 interface in the
TPS Interface
Interface
Applied firmware package: v1.3.1
HDM
-TIPS-TX110AY series – User's Manual
1 2 3 1 2-3
Emitter – 2-pole TS
Signal (active low) 1 Tip +5V
GND 2 Ring
Signal (active low)
+5V 3 Sleeve
Ring pole of the emitter is optional. If your IR emitter has
section.
Pin nr. Signal
1 Ground
2 TX data
3 RX data
RS-232 connector pin assignments
Combicon series (3.5mm pitch, 3-pole), type: MC 1.5/3-PST-3.5.
®
section.
LDC software: v1.33.0b5 LDU2 software: v2.0.0b22
3.3.8. Relay Connector
The receiver contains a 4-pole Ihoenix connector which
is used for relay connection.
Pin nr.
1
2
1 2 3 4
3
RELAY 1 RELAY 2
4
Relay connector pin assignment

NFF:
The maximum ratings for each relay are 30V and 1A, AC/DC.
Compatible Plug Type
Phoenix Combicon series (3.5mm pitch, 4-pole), type: MC 1.5/4-PST-3.5.
®
You can find more information about relay interface in the
Interface section.
3.4. TPS Receiver Concept
HDMI-TPS-RX110AY is a multifunctional receiver with HDBaseT
(TPS) technology. The device can be controlled via many kind of
interfaces, e.g. Ethernet, USB, RS-232, and Infrared. The receiver is
built with audio de-embedder and relay function.
INPUT
HDMI
Ethernet
TPS
RELAYS
RS-232
MAX 30V, 1A
Infrared
Power
+ Ethernet
+ RS-232
+ Infrared
Serial
+ Local USB
+ Relay
Summary of the interfaces
14
Signal
Pin 1 for Relay 1
Pin 2 for Relay 1
Pin 1 for Relay 2
Pin 2 for Relay 2
Relay
TM
OUTPUT
HDMI
CONTROL RS-232 LIVE RESET Analog audio
RS-232
AUDIO OUT
TPS LINK
IR IN IR OUT TX RX ETHERNET FUNCTION