Perkins 4006-23 Operation And Maintenance Manual page 41

SEBU9077-01
(Table 14, contd)
Pour Point °C
Sulfur %mass
Kinematic Viscosity (4) "MM
Water and sediment % weight
Water % weight
Sediment % weight
Gums and Resins (5) mg/100mL
mm
Lubricity correctedwear
scar diameter at 60 °C
(140 °F). (6)
-
Fuel cleanliness (7)
(1) In order to insure minimum cetane number of 40 a distillate diesel fuel should have minimum cetane index of 44 when ASTM D4737 test
method is used. A fuel with a higher cetane number is recommended to operate at a higher altitude or in cold weather.
(2) Density range allowed includes summer and winter diesel fuel grades. Fuel density varies depending on the sulfur level where high sulfur
fuels have higher densities. Some unblended alternative fuels have lower densities which are acceptable, if all the other properties meet this
specification.
(3) Regional regulations, national regulations, or international regulations can require a fuel with a specific sulfur limit. Consult all applicable reg-
ulations before selecting a fuel for a given engine application. LSD fuel with less than 0.05 percent (≤ 500 ppm (mg/kg)) sulfur is strongly rec-
ommended for use in these engine models. Diesel fuel with more than 0.05 percent (≥ 500 ppm (mg/kg)) sulphur can be used only where
allowed by legislation. Fuel sulfur levels affect exhaust emissions. High sulfur fuels also increase the potential for corrosion of internal compo-
nents. Fuel sulfur levels above 0.05% may significantly shorten the oil change interval. For additional information, refer to General lubricant
Information.
(4) The values of the fuel viscosity are the values as the fuel is delivered to the fuel injection pumps. Fuel should also meet the minimum viscos-
ity requirement and the fuel should meet the maximum viscosity requirements at 40° C (104° F) of either the "ASTM D445" test method or
the "ISO 3104" test method. If a fuel with a low viscosity is used, cooling of the fuel may be required to maintain 1.4 cSt or greater viscosity at
the fuel injection pump. Fuels with a high viscosity might require fuel heaters to lower the viscosity to 4.5 cSt at the fuel injection pump.
(5) Follow the test conditions and procedures for gasoline (motor).
(6) The lubricity of a fuel is a concern with low sulfur and ultra low sulfur fuel. To determine the lubricity of the fuel, use the "ISO 12156-1 or ASTM
D6079 High Frequency Reciprocating Rig (HFRR)" test. If the lubricity of a fuel does not meet the minimum requirements, consult your fuel
supplier. Do not treat the fuel without consulting the fuel supplier. Some additives are not compatible. These additives can cause problems in
the fuel system.
(7) Recommended cleanliness level for fuel as dispensed into machine or engine fuel tank is "ISO 18/16/13 or cleaner as per ISO 4406. Refer to
the "Contamination Control Recommendations for Fuels" in this chapter.
NOTICE
Operating with fuels that do not meet the Perkins rec-
ommendations can cause the following effects: Start-
ing difficulty, poor combustion, deposits in the fuel
injectors, will reduce service life of the fuel system.
Deposits in the combustion chamber will reduce serv-
ice life of the engine.
Engines that are manufactured by Perkins are certi-
fied with the fuel that is prescribed by the United
States Environmental Protection Agency. Engines
that are manufactured by Perkins are certified with
the fuel that is prescribed by the European Certifica-
tion and other regulatory agencies. Perkins does not
certify diesel engines on any other fuel.
6 °C (10°F)
Minimum below ambient
temperature
(3)
2
/S (cSt)" The viscosity of the fuel that
is delivered to the fuel injec-
tion pump. "1.4 minimum
and /4.5 maximum"
0.05% maximum
0.05% maximum
0.05% maximum
10 mg per 100 mL
maximum
0.46 maximum
"ISO"18/16/13
"D97"
"D5453 or /D26222"
"D445"
"D1796"
"D1744"
"D473"
"D381"
"D6079"
"7619"
Note: The owner and the operator of the engine has
the responsibility of using the fuel that is prescribed
by the Environmental Protection Agency (EPA) and
other appropriate regulatory agencies.
Diesel Fuel Characteristics
Perkins Recommendations
Cetane Number
Fuel that has a high cetane number will give a shorter
ignition delay. A high cetane number will produce a
better ignition quality. Cetane numbers are derived
for fuels against proportions of cetane and
heptamethylnonane in the standard CFR engine.
Refer to "ISO 5165" for the test method.
41
Maintenance Section
Fuel Specifications
"ISO 3016"
"ISO 20846" or "ISO 20884"
"ISO 3405"
"ISO 3734"
No equivalent test
"ISO 3735"
"ISO 6246"
"ISO 12156-1"
"ISO 4406"