Modifications 0.1 Preliminary version 0.2 Preliminary version, change of the fan plug from 3 to 4-pin, OCT UPS, OCT LED inserted, graphics for LEDs changed, mechanical drawings updated 0.3 Interface assignment added 0.4 Isolated BAseCon plug added CB6464 Version: 0.4...
All the components are supplied in particular hardware and software configurations appropriate for the application. Modifications to hardware or software configurations other than those described in the documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG. Personnel qualification This description is only intended for trained specialists in control, automation and drive engineering who are familiar with the applicable national standards.
Two variants are available, variant 1 being equipped with a Q170 chipset and variant 2 with an H110 chipset. Internally both variants of the CB6464 have two M.2 (B) sockets (2280), while variant 1 additionally has a BAseCon140 connector. Various signals, which are listed in the respective chapter, are led out via the internal plug connector depending on the chipset in use.
Overview List of features CB6464 120x120-Board CPU Intel® Core™ i3 / Core™ i5 / Core™ i7 Intel® Pentium® Intel® Celeron® Memory 2x SO-DIMM260 1.2V DDR4-2133 Maximum memory extension 32GB I/O on front panel 2x DisplayPort++ (connection of an HDMI adapter for a HDMI signal is possible) 4x GB LAN...
ACPI-Spezification Version 3.0 www.acpi.info ATA/ATAPI-Spezification Version 7 Rev. 1 www.t13.org USB-Spezificationen www.usb.org SM-Bus-Spezification Version 2.0 www.smbus.org Intel®-chip description Intel® Atom™ Processor E3800 Product Family datasheet www.intel.com Intel®-chipd description i210 Datasheet www.intel.com SMSC®-chip description SCH3114 Datasheet (NDA erforderlich) Version: 0.4 CB6464...
Page 13
Overview www.smsc.com American Megatrends® Aptio™ Text Setup Environment (TSE) User Manual www.ami.com American Megatrends® Aptio™ 4.x Status Codes www.ami.com CB6464 Version: 0.4...
M.2 cards can easily and simply be inserted by plugging them into the slot and fixing them with a screw. The M.2 socket of the CB6464 supports Key B. Different signals are supported depending on the chipset in use. The table in chapter M.2 lists all the interfaces supported, depending on the chipset in use.
USB 2.0 connection. Limitations in the maximum cable length are also no rarity. All of these interface-specific requirements are to be taken from the re- spective specifications and observed accordingly. CB6464 Version: 0.4...
External connections Connector Map The plug connections on the component side of the CB6464 board are summarized in the illustration below. The function of the respective connector can be taken from the table below the illustration, as can the page of the manual on which further information about this connection can be read.
Internal: BAseCon140 (Q170 only) [} 24] P500/501 FAN Internal: Battery [} 29] BT1200* Battery Internal: FAN [} 28] *not depicted (see bottom of board) The numbers in brackets correspond to the inscription of the external interfaces on the front housing of the industrial pc. CB6464 Version: 0.4...
UPS-OCT (One Cable Technology), i.e. the signal for the UPS is also transmitted to the board via this cable. Fig. 3: CB6464 Vin 90° plug As the plug is a 90° plug, the plug symbol in the illustration is oriented to what you see when you look at the board from the side (instead of from above).
The Ethernet port integrated in the chipset is usually suitable for real-time Ethernet applications with cycle times > 1 ms (without distributed clocks). Fig. 4: CB6464 LAN 90° plug As the plug is a 90° plug, the plug symbol in the illustration is oriented to what you see when you look at the board from the side (instead of from above).
External connections Front panel: USB 3.0 A-D (X106 - X109) The CB6464 provides four USB 3.0 ports, which are implemented as combination connectors with 4 connectors. The USB channels support the USB 3.0 specification. All necessary settings for USB can be made in the BIOS.
The interface additionally provides HDMI/DVI signals that can be used with aid of an adapter. Please consult your distributor with regard to a suitable adapter. Fig. 6: CB6464 Display Port 90° plug As the plug is a 90° plug, the plug symbol in the illustration is oriented to what you see when you look at the board from the side (instead of from above).
Internal connections Internal connections Internal: M.2 The CB6464 is equipped with two M.2 sockets, into each of which an M.2-2280 card (Key B) is inserted. Various signals are led out via the socket, depending on the chipset (see table). Q170 H110...
Page 23
Power good RESET# 68 SUSCLK System clock Configuration pin CFG1 70 3.3 V Standby supply voltage S 3.3 V Ground GND 72 3.3 V Standby supply voltage S 3.3 V Ground GND 74 3.3 V Standby supply voltage S 3.3 V Configuration pin CFG2 CB6464 Version: 0.4...
In conjunction with the Q170 chipset, the BAseCon140 connector enables the flexible extension of the IO functions of the CB6464. It provides up to eight PCIe lanes, of which a maximum of four can be multiplexed with SATA 2.0 (3G) and a maximum of four with PCIe lines, as well as a maximum of four PCIe lines with a maximum of four USB 3.0 lines (see table).
Page 25
PCIe Reset active PERST# PEWAKE# PCIe Wake active low low SMBus Clock SMBCLK SMBDAT SMBus Data SMBus Alert active SMB-Alert# 1Wire 1-Wire low PCIe Clock Enable PCKE5/OC4# PCKE6#/ PCIe Lane 6 Clock Lane 5 OC3# Enable 6 - CB6464 Version: 0.4...
Page 26
PE8 RX# Receive - Ground GND GND Ground SATA GP1 GPIO1/ SATAGP2/ SATA GP 2 SATAGP1 GPIO2 SATA GP3 GPIO3/ USB-CC2/ SATA GP4 SATAGP3/ SATAGP4/ USBC-CC1 GPIO4 TwinCAT LED Red GPIO5/ GPIO6/ TwinCAT LED TCLEDR TCLEDG Green Version: 0.4 CB6464...
Page 27
Lane 0 + Lane 1 + DisplayPort DPL0# DPL1# DisplayPort Lane 0 - Lane 1 - Ground GND GND Ground DisplayPort DPL2 DPL3 DisplayPort 3 + Lane 2 + DisplayPort DPL2# DPL3# DisplayPort 3 - Lane 2 - CB6464 Version: 0.4...
The module has two 4-pin fan connections. This enables fans with a supply voltage of 12 V to be connected directly to the module. A signal is also available for monitoring the fan speed. Fig. 7: CB6464 FAN Pin assignment of fan connector: Pin...
Accordingly, no additional actions are necessary for the connection of an RTC battery. The battery must be connected directly. Fig. 8: CB6464 Bat Synchronism of the RTC The quartz of the RTC reacts to temperature fluctuations. Therefore, correct synchronism of the...
LED’s LED’s LED: Powercontroller There is a RGB LED on the board with which status messages of the power controller are output by means of colors and flashing intervals. Fig. 9: CB6464 PWRCTRL-LED Color Interval Meaning None Steadily lit System in error state White...
LED’s LED: SATA A further RGB LED indicates the hard disk activity. Fig. 10: CB6464 SATA-LED Color Interval Meaning Red Flashing Acitvity (access) CB6464 Version: 0.4...
LED’s LED: TwinCAT Fig. 11: CB6464 TwinCAT-LED Color Interval Meaning Green Steadily lit TwinCAT Run Mode Blue Steadily lit TwinCAT Config Mode Red Steadily lit TwinCAT stop Adaptation of the status codes It is possible to adapt the status codes (e.g. as TwinCAT LED). To do this, the system colors can be changed with the aid of an SMB command.
LED’s LED: UPS-OCT There is a RGB LED on the board with which the transmission quality of the UPS-OCT signals is indicated by means of colors and flashing intervals. Fig. 12: CB6464 OCT-LED Color Interval Meaning None Steadily lit No UPS-OCT connected Blue...
None Total Memory None Memory Frequency None System Date Here the systemdate can be changed. System Time Here the systemtime can be changed. *PCH Typ Automatic indication of variant: CB6464 V1 → Q170 CB6464 V2 → H110 Version: 0.4 CB6464...
Options Port Configuration NIC Configuration Submenu see: NIC Configuration [} 39] Blink LEDs Port Configuration Information UEFI Driver None Adapter PBA None Chip Type None PCI DEcice ID None PCI Address None Link Status None MAC Address None Version: 0.4 CB6464...
Disabled / 1 M / 2 M / 4 M / 8 M / 16 M / 32 M / 64 M / 128 M PFMMIO 32 bit Resources Padding Disabled / 1 M / 2 M / 4 M / 8 M / 16 M / 32 M / 64 M / 128 M CB6464 Version: 0.4...
Option ROM execution Network Do not launch / UEFI / Legacy Storage Do not launch / UEFI / Legacy Video Do not launch / UEFI / Legacy Other PCI devices Do not launch / UEFI / Legacy Version: 0.4 CB6464...
Disabled / Enabled Cinfigured as eSATA None Spin Up Device Disabled / Enabled Topology Unknown / ISATA / Direct Connect / FLEX / M2 SATA Port X Dev Slp Disabled / Enabled DITO Configuration Disabled / Enabled Version: 0.4 CB6464...
2048x1536 LVDS / 1366x768 LVDS Panel Scaling Auto / Off / Force Scaling Backlight Control PWM Inverted / PWM Normal Active LFP Noe DP / eDP Port-A Panel Color Depth 18 Bit / 24 Bit Backlight Brightness 0..255 Version: 0.4 CB6464...
Second LAN Controller Enabled / Disabled Third LAN Controller Enabled / Disabled Forth LAN Controller Enabled / Disabled M.2-Slot X None CLKRUN#logic Enabled / Disabled State After G3 S0 State / S5 State Compatible Revision ID Enabled / Disabled CB6464 Version: 0.4...
Boot mode select Legacy / UEFI / Dual Fixed Boot Order Priorities Boot Option #1-19 Here the range of boot media to be used can be set. Advanced Fixed Boot Order Submenu see: Fixed Boot Order Parameters [} 62] Parameters CB6464 Version: 0.4...
Mechanical drawings Mechanical drawings Dimensional notation All dimensions are in mil (1 mil = 0.0254 mm). Data in square brackets are in mm. 10.1 PCB: Holes Fig. 13: MZ MH CB6464_G3 CB6464 Version: 0.4...
5 up to 9 Hz, 3.5 mm amplitude 9 up to 500 Hz, 10 m/s², for wrapped boards Note on impact and vibration resistance The specifications for impact and vibration resistance refer only to the motherboard itself without heat sink, memory module, cabling, etc. Version: 0.4 CB6464...
It is the end customer's responsibility to ensure that the die temperature of the processor does not exceed 100 °C! Continuous overheating can destroy the board! If the temperature exceeds 100 °C, the ambient temperature needs to be reduced. Ensure sufficient air cir- culation if necessary. CB6464 Version: 0.4...
Support and Service 12.1 Beckhoff Support Beckhoff Support offers you comprehensive technical assistance, helping you not only with the application of individual Beckhoff products, but also with other, wide-ranging services: • world-wide support • design, programming and commissioning of complex automation systems •...
Codes are explained in the document "Aptio™ 5.x Status Codes" from American Megatrends®, which is available from the website http://www.ami.com. In addition, the following OEM POST Codes are output: Code Description BIOS-API started PCA9535 started PWRCTRL firmware started CB6464 Version: 0.4...
AT compatibility. If interrupts have to be exclusively available on the ISA side, they must be reserved through the BIOS setup. Exclusivity is neither given nor possible on the PCI side. Address Function IRQ0 Timer IRQ1 IRQ2 IRQ3 IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 Version: 0.4 CB6464...
36-39 Reserved 5C-5D NCT7491 60-6F Reserved for DDR4 70-73 POST Code output 88-89 Slave address defined by BIOS 92-93 I210 default A0-A7 Reserved for DDR4 B0-B3 Power controller (access via BIOS-API) B8-BB Power controller (access via BIOS-API) Version: 0.4 CB6464...